| Age | Commit message (Collapse) | Author |
|---|
|
Move
arch/arm/cpu/arm926ejs/davinci/* -> arch/arm/mach-davinci/*
Signed-off-by: Masahiro Yamada <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
In f0c3a6c we stopped setting gd in board_init_f, but later had to
revert to due problems on certain platforms. As davinci does not look
to have these problems, we can drop the setting here and rely upon
crt0.S to do it.
Cc: Peter Howard <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This commit introduces a Kconfig symbol for each ARM CPU:
CPU_ARM720T, CPU_ARM920T, CPU_ARM926EJS, CPU_ARM946ES, CPU_ARM1136,
CPU_ARM1176, CPU_V7, CPU_PXA, CPU_SA1100.
Also, it adds the CPU feature Kconfig symbol HAS_VBAR which is selected
for CPU_ARM1176 and CPU_V7.
For each target, the corresponding CPU is selected and the definition of
SYS_CPU in the corresponding Kconfig file is removed.
Also, it removes redundant "string" type in some Kconfig files.
Signed-off-by: Georges Savoundararadj <[email protected]>
Acked-by: Albert ARIBAUD <[email protected]>
Cc: Masahiro Yamada <[email protected]>
|
|
CONFIG_SPL should not be enabled for boards that do not have SPL.
CONFIG_SUPPORT_SPL introduced by this commit should be "select"ed
by boards with SPL support and CONFIG_SPL should depend on it.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.
We can delete the ones in arch and board Kconfig files.
This commit can be easily reproduced by the following command:
find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
N
s/\n[[:space:]]*string//
}
'
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Davinci board select menu to davinci/Kconfig.
Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="davinci").
Signed-off-by: Masahiro Yamada <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Cc: Heiko Schocher <[email protected]>
Cc: Sandeep Paulraj <[email protected]>
|
|
The definitions inside emif_defs.h concern davinci nand driver and
should be in it's header. So create header file for davinci nand
driver and move definitions from emif_defs.h and nand_defs.h to it.
Acked-by: Vitaly Andrianov <[email protected]>
Signed-off-by: Ivan Khoronzhuk <[email protected]>
[trini: Fixup more davinci breakage]
Signed-off-by: Tom Rini <[email protected]>
|
|
Make funtions static which are locally used in file
and remove the declaration from header file.
Signed-off-by: Manish Badarkhe <[email protected]>
|
|
- add davinci driver to new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Vitaly Andrianov <[email protected]>
Signed-off-by: Murali Karicheri <[email protected]>
Acked-by: Heiko Schocher <[email protected]>
|
|
This commit changes the working directory
where the build process occurs.
Before this commit, build process occurred under the source
tree for both in-tree and out-of-tree build.
That's why we needed to add $(obj) prefix to all generated
files in makefiles like follows:
$(obj)u-boot.bin: $(obj)u-boot
Here, $(obj) is empty for in-tree build, whereas it points
to the output directory for out-of-tree build.
And our old build system changes the current working directory
with "make -C <sub-dir>" syntax when descending into the
sub-directories.
On the other hand, Kbuild uses a different idea
to handle out-of-tree build and directory descending.
The build process of Kbuild always occurs under the output tree.
When "O=dir/to/store/output/files" is given, the build system
changes the current working directory to that directory and
restarts the make.
Kbuild uses "make -f $(srctree)/scripts/Makefile.build obj=<sub-dir>"
syntax for descending into sub-directories.
(We can write it like "make $(obj)=<sub-dir>" with a shorthand.)
This means the current working directory is always the top
of the output directory.
Signed-off-by: Masahiro Yamada <[email protected]>
Tested-by: Gerhard Sittig <[email protected]>
|
|
Note1:
In arch/arm/cpu/arm926ejs/spear/Makefile
START := start.o
was changed
extra-$(CONFIG_SPL_BUILD) := start.o
because spear/start.o is only used for SPL.
Note2:
START := start.o
was missing from arch/arm/cpu/arm926ejs/mxs/Makefile.
This commit simply adds
extra-$(CONFIG_SPL_BUILD) := start.o
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
in arch_cpu_init() uart2 is fix enabled, without reference the
setting from CONFIG_SYS_NS16550_COM1. Use the setting from
CONFIG_SYS_NS16550_COM1 for enabling the console.
Signed-off-by: Heiko Schocher <[email protected]>
Cc: Albert ARIBAUD <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Christian Riesch <[email protected]>
|
|
emac_pins_rmii pinmux
Signed-off-by: Heiko Schocher <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <[email protected]>
|
|
Move pinmux configurations for the DA830 SoCs from board file
to the arch tree so that it can be used for all da830 based devices.
Also, avoids duplicate pinmuxing in case of NAND.
Signed-off-by: Vishwanathrao Badarkhe, Manish <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Acked-by: Christian Riesch <[email protected]>
|
|
this is needed to bring UART0 out of reset but this function
currently only exists for dm644x/355/365/646x when da850 (at
least am1808 also need it).
Signed-off-by: Eric Bénard <[email protected]>
|
|
Note this is a tree-wide change affecting multiple architectures.
At present we use __bss_start, but mostly __bss_end__. This seems
inconsistent and in a number of places __bss_end is used instead.
Change to use __bss_end for the BSS end symbol throughout U-Boot. This
makes it possible to use the asm-generic/sections.h file on all
archs.
Signed-off-by: Simon Glass <[email protected]>
|
|
The issue got introduced in a cleanup by Manjunath Hadli in commit
826e99136e2bce61f3f6572e32d7aa724c116e6d. The eth_getenv_enetaddr_by_index
method will validate the MAC addr and if none is set in the environment
0 will be returned. Set the MAC from the eeprom if no valid address
is found in environment.
Signed-off-by: Holger Hans Peter Freyther <[email protected]>
|
|
Move this field into arch_global_data and tidy up.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this field into arch_global_data and tidy up.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this field into arch_global_data and tidy up.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this field into arch_global_data and tidy up.
Signed-off-by: Simon Glass <[email protected]>
|
|
The reset procedure works on watchdog timer while before it was modifying
TIMER_1 registers.
Tested on DM365.
Signed-off-by: Davide Bonfanti <[email protected]>
|
|
- Convert the non-relocation part of board_init_f to spl_board_init, turn on CONFIG_SPL_BOARD_INIT in the configs.
- Remove duplicated code.
- Add spl_boot_device() that returns the statically chosen boot device.
Signed-off-by: Tom Rini <[email protected]>
|
|
We can safely use the same reset code written in C for both Davinci and
C6X platforms. In addition the C version of the code is marginally
smaller on Davinci.
Tested-by: Matt Porter <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Also enable the ohci port on hawkboard. These additions result in an
increased u-boot size -- adjust the same accordingly in the board's
config.
Move the usb header for da8xx platforms under arch-davinci.
Signed-off-by: Sughosh Ganu <[email protected]>
|
|
For the DA8xx family of SoCs, the set_cpu_clk_info() function was not
initialising the DSP frequency, leading to 'bdinfo' command output such as:
[...snip...]
ARM frequency = 300 MHz
DSP frequency = -536870913 MHz
DDR frequency = 300 MHz
This commit provides a separate implementation of set_cpu_clk_info() for
the DA8xx SoCs that initialises the DSP frequency to zero (since
currently the DSP is not enabled by U-Boot on any DA8xx platform). The
separate implementation is justified because there is no common code
between DA8xx and the other SoC families. It is now much easier to
understand the flow of the two separate functions.
Signed-off-by: Laurence Withers <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Hadli, Manjunath <[email protected]>
Cc: Heiko Schocher <[email protected]>
|
|
Replace a magic number for the DDR2/mDDR PHY clock ID with a proper
definition. In addition, don't request this clock ID on DA830 hardware,
which does not have a DDR2/mDDR PHY (or associated PLL controller).
Signed-off-by: Laurence Withers <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Prabhakar Lad <[email protected]>
|
|
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
Tested-by: Sughosh Ganu <[email protected]>
|
|
follow section 15.2.13.1 (Initializing Following Device Power Up or Reset) of
OMAP-L138 DSP+ARM Processor Technical Reference Manual
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
Acked-by: Christian Riesch <[email protected]>
Tested-by: Christian Riesch <[email protected]>
|
|
DA850/OMAP-L138 does not support strict MMC/SD boot mode. SPL will
be in SPI flash and U-Boot image will be in MMC/SD card. SPL will
do the low level initialization and then loads the u-boot image
from MMC/SD card.
Define CONFIG_SPL_MMC_LOAD macro in the DA850/OMAP-L138
configuration file to enable this feature.
Tested-by: Christian Riesch <[email protected]>
Signed-off-by: Lad, Prabhakar <[email protected]>
Signed-off-by: Rajashekhara, Sudhakar <[email protected]>
Signed-off-by: Hadli, Manjunath <[email protected]>
|
|
initialize baudrate, flags, data and serial initialization,
only when CONFIG_SPL_LIBCOMMON_SUPPORT is defined.
Tested-by: Christian Riesch <[email protected]>
Signed-off-by: Lad, Prabhakar <[email protected]>
Signed-off-by: Rajashekhara, Sudhakar <[email protected]>
Signed-off-by: Hadli, Manjunath <[email protected]>
Acked-by: Christian Riesch <[email protected]>
|
|
This patch adds support for MMC/SD on DA850/OMAP-L138.
Tested-by: Christian Riesch <[email protected]>
Signed-off-by: Lad, Prabhakar <[email protected]>
Signed-off-by: Rajashekhara, Sudhakar <[email protected]>
Signed-off-by: Hadli, Manjunath <[email protected]>
|
|
Previously, only the low 5 bits (NCH) were being transfered
from DDRVTPR to DDRVTPIOCR, the bits 5-9 where zeroed.
VTP_RECAL should be bit 15, not 18.
The only mainline board affected by this change is davinci_sonata.
The other Davinci boards define CONFIG_SKIP_LOWLEVEL_INIT.
However, if the program that loads u-boot on these boards
copied the code from u-boot, they will need fixed as well.
Signed-off-by: Troy Kisky <[email protected]>
Please get tested by acks before applying, where tested by
means an overnight memory test.
Thanks
Troy
|
|
davinci_dm6467Tevm
In commit 2d575e46859dd9127a9cec731ace77523e6ea2ab a separate header
file was introduced for the DM6467T EVM, include/configs/davinci_dm6467Tevm.h.
The substantial difference between the davinci_dm6467evm and the
davinci_dm6467Tevm configuration is a single bit in the hardware revision
that is passed to the Linux kernel and davinci_dm6467evm has
REFCLK_FREQ = 27000000 where as davinci_dm6467Tevm.h has a
REFCLK_FREQ = 33000000.
This patch removes include/configs/davinci_dm6467Tevm.h. Instead the
include/configs/davinci_dm6467evm.h configuration is used for DM6467T EVMs and
renamed CFG_REFCLK_FREQ to CONFIG_REFCLK_FREQ and CONFIG_REFCLK_FREQ is defined
in boards.cfg.
Signed-off-by: Prabhakar Lad <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
check for the return status for eth_getenv_enetaddr_by_index()
and eth_setenv_enetaddr() functions and print appropriate message
on failure.
Signed-off-by: Manjunath Hadli <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Mike Frysinger <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Acked-by: Mike Frysinger <[email protected]>
|
|
This patch moves hawkboard to the new spl infrastructure from the
older nand_spl one.
Removed the hawkboard_nand_config build option -- The spl code now
gets compiled with hawkboard_config, after building the main u-boot
image, using the CONFIG_SPL_TEXT_BASE. Modified the README.hawkboard
to reflect the same.
Signed-off-by: Sughosh Ganu <[email protected]>
Signed-off-by: Heiko Schocher <[email protected]>
Cc: Heiko Schocher <[email protected]>
Cc: Christian Riesch <[email protected]>
Cc: Sudhakar Rajashekhara <[email protected]>
Cc: Tom Rini <[email protected]>
Acked-by: Christian Riesch <[email protected]>
|
|
The low level initialization code in
arch/arm/cpu/arm926ejs/davinci/lowlevel_init.S was written for
DM644X SoCs only. This patch makes the lowlevel_init function in this
file a dummy function for SoCs other than DM644X.
Signed-off-by: Christian Riesch <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Sergey Kubushyn <[email protected]>
Acked-by: Heiko Schocher <[email protected]>
Tested-by: Heiko Schocher <[email protected]>
|
|
add support for printing various clock frequency info found
in SOC such as ARM core frequency, DSP core frequency and DDR
frequency as part of bdinfo command.
Signed-off-by: Manjunath Hadli <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
remove the macro CONFIG_DISPLAY_CPUINFO as it is no longer
required. This is because clock info will be printed as part
'bdinfo' command and also remove support print_cpuinfo() as it will
no longer be called.
Signed-off-by: Manjunath Hadli <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
The Buffer Logic of VPSS is Not Reset by System Reset Pin, see
http://www.ti.com/lit/er/sprz316b/sprz316b.pdf chapter Advisory 1.2.1
on page 9. Add workaroundcode proposed in the errata.
Signed-off-by: Heiko Schocher <[email protected]>
Cc: Sandeep Paulraj <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
The OMAP-L138 has a pre-divider available on PLL0.
Add support to da850_lowlevel.c for configuring PLL0's pre-divider. This is
to achieve certain OPP's -- e.g. the 372MHz OPP used also by Linux.
Signed-off-by: Ben Gardiner <[email protected]>
Cc: Christian Riesch <[email protected]>
CC: Heiko Schocher <[email protected]>
Cc: Sandeep Paulraj <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Albert ARIBAUD <[email protected]>
Acked-by: Heiko Schocher <[email protected]>
Acked-by: Christian Riesch <[email protected]>
|
|
This patch fixes a build warning for the cam_enc_4xx board introduced by
commit d6ec0c0dfc70447cf615ae80a952da81f73f16b4:
spl.c:35:13: warning: 'gdata' defined but not used
spl.c:36:13: warning: 'bdata' defined but not used
Signed-off-by: Christian Riesch <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Heiko Schocher <[email protected]>
|
|
This code adds an SPL for booting from SPI flash on DA850 SoCs.
Signed-off-by: Christian Riesch <[email protected]>
Cc: Heiko Schocher <[email protected]>
Cc: Sandeep Paulraj <[email protected]>
Cc: Tom Rini <[email protected]>
Acked-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Manfred Rudigier <[email protected]>
|
|
Signed-off-by: Christian Riesch <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Heiko Schocher <[email protected]>
Cc: Wolfgang Denk <[email protected]>
|
|
move the board/davinci/common/misc.c file to
arch/arm/cpu/arm926ejs/davinci/misc.c, so all
davinci boards can use this functions.
Signed-off-by: Heiko Schocher <[email protected]>
Cc: Sandeep Paulraj <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Albert ARIBAUD <[email protected]>
Cc: Christian Riesch <[email protected]>
|
|
Signed-off-by: Heiko Schocher <[email protected]>
Acked-by: Tom Rini <[email protected]>
Cc: Sandeep Paulraj <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Albert ARIBAUD <[email protected]>
Cc: Christian Riesch <[email protected]>
|
|
This patch replaces the pinmux configuration code in
arch/arm/cpu/arm926ejs/davinci/da850_lowlevel.c by the code from
arch/arm/cpu/arm926ejs/davinci/pinmux.c.
Signed-off-by: Christian Riesch <[email protected]>
Cc: Sandeep Paulraj <[email protected]>
Acked-by: Heiko Schocher <[email protected]>
|
