| Age | Commit message (Collapse) | Author |
|---|
|
TARGET namespace is for machines / boards / what-have-you that
building U-Boot for. Simply replace from TARGET to ARCH
make things more clear and proper for ALL SoCFPGA.
Signed-off-by: Brian Sune <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
# Conflicts:
# drivers/ddr/altera/Makefile
|
|
For successful reset staggering pulse operation, reset pulse
override bit is set. Port overcurrent bit 1, which in reality
reflects PIPE power present signal is set to avoid giving
false information of Vbus status to HPS controller.
Signed-off-by: Naresh Kumar Ravulapalli <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
API declarations
The QSPI mailbox API function declarations (mbox_qspi_close and
mbox_qspi_open) in mailbox_s10.h were guarded by CONFIG_CADENCE_QSPI
preprocessor conditional. This prevented their prototypes from being
visible to code that may use the stub implementations when
CONFIG_CADENCE_QSPI is disabled.
Remove the CONFIG_CADENCE_QSPI preprocessor conditional so these functions
are always declared, regardless of the configuration. This avoids potential
build or linkage errors when stubs are used.
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Agilex5 FPGA switch section in the handoff data is larger by 32 bytes
than the default value as these extra sections contains I3C0 and I3C1
register offsets and values with 4 bytes each.
This requires 4 more times of reading the FPGA switch section of the
handoff data to fully populate the handoff data table in the memory
during runtime.
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
This is for new platform enablement for Agilex7 M-series.
Add DDR driver for Agilex7 M-series. This driver is designed to support
DDR and HBM memory. The official HBM handoff is not ready yet, therefore
hardcoded handoff is used for HBM driver validation on mUDV board.
Signed-off-by: Tingting Meng <[email protected]>
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Agilex7 M-series reuse the clock driver from Agilex.
Signed-off-by: Tingting Meng <[email protected]>
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Handoff settings updated for new platform Agilex7 M-series.
Signed-off-by: Tingting Meng <[email protected]>
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Add platform related files for new platform Agilex7 M-series.
Signed-off-by: Tingting Meng <[email protected]>
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
SPL checks for a magic word in the system manager's scratch
register to determine if an L2 reset has occurred. If detected,
SPL places all slave CPUs (CPU1–3) into WFI mode. The master
CPU (CPU0) then initiates a warm reset by writing to the RMR_EL3
system register and also enters WFI mode.
This warm reset flow is handled entirely within the HPS. The
function `socfpga_sysreset_request()` triggers the warm
reset, and upon SPL re-entry, the updated `lowlevel_init_soc64.S`
handles the necessary initialization.
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
The DDR data rate must be set correctly in the DDRIOCTRL
register according to the Actual Clock Frequency (ACF) value.
By enabling the reading of ACF value from bit 18 of the boot
scratch register during initialization, the DDR data rate is
able to be configured accurately.
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
The boot scratch cold reg 8 is shared between DBE, DDR init progress
update and Linux EDAC. This patch defines how the bits are used by
respective features above and their macro names used in U-Boot.
Signed-off-by: Tien Fong Chee <[email protected]>
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Refactor system manager initialization by searching for system manager
alias in Agilex5 device tree instead of manually passing node name to
the device model calling function
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Agilex5 FSBL is required to disable the power of unused peripheral SRAM
blocks to reduce power consumption.
Introducing a new power manager driver for Agilex5 which will be called
as part of Agilex5 SPL initialization process.
This driver will read the peripheral handoff data obtained from the
bitstream and will power off the specified peripheral's SRAM from the
handoff data values.
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
All the source code of secure_vab.c and secure_vab.h are from Intel
and Altera. Updating the license to use either GPL-2.0 or
BSD-3-Clause because this copy of code may be used for open source
and internal project.
Signed-off-by: Naresh Kumar Ravulapalli <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Use consistent lowercase hex prefix style in arch/*
Signed-off-by: E Shattow <[email protected]>
|
|
Enable reset support for FPGA2SDRAM bridge for Stratix10, as well as
FPGA2SoC and SoC2FPGA bridges for all SoC64 families.
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Add reset manager registers in preparation for F2S bridge reset
support as well as the mask support to enable/disable the bridges.
Mask value:
BIT0: soc2fpga
BIT1: lwhps2fpga
BIT2: fpga2soc
These bridges are available only in Stratix10:
BIT3: f2sdram0
BIT4: f2sdram1
BIT5: f2sdram2
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Introducing a new mailbox command "HPS_STAGE_NOTIFY" to notify Secure
Device Manager (SDM) on the stage of HPS code execution.
Generally, there are three main code execution stages: First Stage Boot
Loader (FSBL) which is U-Boot SPL, Second Stage Boot Loader (SSBL) which
is U-Boot, and the Operating System (OS) which is Linux.
This enables the user to query the SDM for HPS error details.
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Adding DDR driver support for Agilex5 series.
Signed-off-by: Tingting Meng <[email protected]>
|
|
Board ID is exported as environment variable for use to boot Linux with FIT
configuration.
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Signed-off-by: Tien Fong Chee <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Agilex5 supports both HPS handoff data and DDR handoff data.
Existing HPS handoff functions are restructured to support both existing
devices and Agilex5 device.
Signed-off-by: Tien Fong Chee <[email protected]>
|
|
There are 5 L4 watchdogs and one SDM triggered warm reset bit
in Agilex5 reset manager "stat" register where bit 16:20 for L4
watchdogs. Assigning value 1 to these bits in the register address
will initiate SDM to trigger warm reset.
Introducing new warm reset mask for Agilex5 to trigger warm reset
to all five L4 watchdogs.
Signed-off-by: Tien Fong Chee <[email protected]>
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Initial creation of new system manager driver.
Add supports for the SOCFPGA System Manager Register block which
aggregates different peripheral function into one area.
On 64 bit ARM parts, the system manager only can be accessed during
EL3 mode, this driver model provide user the high level access
to system register and abstract user from low level access.
The base address of system manager can be retrieved
using DT framework through the System Manager driver.
Signed-off-by: Tien Fong Chee <[email protected]>
Signed-off-by: Boon Khai Ng <[email protected]>
|
|
Currently the FPGA reconfig status only return a single error status
which make the debugging of FPGA reconfiguration hard.
This patch is to expose the error status, major error code and
minor error code, for the FPGA reconfig to upper layer app.
Signed-off-by: Boon Khai Ng <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
This commit is to fix the system manager watchdog mode setting to support
until mode_4 for Agilex5. This changes can refer to system manager register
map on wddbg fields.
In Agilex7 it is not detected as an issue because Agilex7 only have 4 watchdog
until mode_3 and it is already been set correctly for it to halt on any CPU in
debug mode. However, in Agilex5 this fix is needed in order to enable the watchdog
pause feature for mode_4 when entering debug mode. If 0xF is not been set on mode_4,
the Watchdog Timers will not halt on any CPU. As by default value, the pause signal
does not assert when any CPU is in debug mode and the watchdog continue to count.
Signed-off-by: Muhammad Hazim Izzat Zamri <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Use the new symbol to refer to any 'SPL' build, including TPL and VPL
Signed-off-by: Simon Glass <[email protected]>
|
|
Drop all duplicate newlines. No functional change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This file has many "Linux" style types in it, add <linux/types.h>
Signed-off-by: Tom Rini <[email protected]>
|
|
Remove <common.h> from all mach-socfpga files and when needed add missing
include files directly.
Signed-off-by: Tom Rini <[email protected]>
|
|
This patch is to enable Agilex5 platform for Intel
product. Changes, modification and new files are
created for board, dts, configs and makefile to
create the base for Agilex5.
Signed-off-by: Jit Loon Lim <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Fix compilation issue with overlapping lwip and march defines.
Signed-off-by: Maxim Uvarov <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Double peripheral RBF configuration are needed on some devices or boards
to stabilize the IO configuration system.
Signed-off-by: Tien Fong Chee <[email protected]>
Signed-off-by: Sin Hui Kho <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
This patch triggers warm reset to recover the MPFE NoC from corruption
due to high frequency transient clock output from HPS EMIF IOPLL at
VCO startup after peripheral RBF is programmed.
Signed-off-by: Tien Fong Chee <[email protected]>
Signed-off-by: Sin Hui Kho <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
The romcode_initswstate register need to be set with FSBL_IMAGE_IS_VALID
value if the current FSBL image is found valid, otherwise BootROM will
look for next subsequent valid FSBL image when warm reset is triggered.
Signed-off-by: Tien Fong Chee <[email protected]>
Signed-off-by: Sin Hui Kho <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
The DDR subsystem in Diamond Mesa is consisted of controller, PHY,
memory reset manager and memory clock manager.
Configuration settings of controller, PHY and memory reset manager
is come from DDR handoff data in bitstream, which contain the register
base addresses and user settings from tool.
Configuration settings of memory clock manager is come from the HPS
handoff data in bitstream, however the register base address is defined
in device tree.
The calibration is fully done in HPS, which requires IMEM and DMEM
binaries loading to PHY SRAM for running this calibration, both
IMEM and DMEM binaries are also part of bitstream, this bitstream
would be loaded to OCRAM by SDM, and configured by DDR driver.
Signed-off-by: Siew Chin Lim <[email protected]>
Signed-off-by: Tien Fong Chee <[email protected]>
|
|
Add clock manager for N5X.
Signed-off-by: Siew Chin Lim <[email protected]>
|
|
Move cm_get_mpu_clk_hz function declaration from individual device's
clock manager header file to common clock_manager.h.
Signed-off-by: Siew Chin Lim <[email protected]>
|
|
N5X support both HPS handoff data and DDR handoff data.
Existing HPS handoff functions are restructured to support both existing
devices and N5X device.
Signed-off-by: Siew Chin Lim <[email protected]>
Signed-off-by: Tien Fong Chee <[email protected]>
|
|
Reuse base_addr_soc64.h for Intel N5X device, the address is the
same as Agilex.
Signed-off-by: Siew Chin Lim <[email protected]>
|
|
Rename to common file name to used by all SOC64 devices and change
"_S10_" to "_SOC64_" in base_addr_soc64.h.
Signed-off-by: Siew Chin Lim <[email protected]>
|
|
Add function to send mailbox command via SMC to get usercode from SDM.
Signed-off-by: Siew Chin Lim <[email protected]>
Reviewed-by: Ley Foon Tan <[email protected]>
|
|
Changed to store QSPI reference clock in kHz instead of Hz in
boot scratch cold0 register for Stratix10 and Agilex.
This patch is in preparation for Intel N5X SDRAM driver
support. Reserved 4 bits for Intel N5X SDRAM driver,
and there will be 28 bits to store QSPI reference clock.
Due to limited bits, QSPI reference clock frequency is
converted to kHz from Hz.
Signed-off-by: Siew Chin Lim <[email protected]>
Signed-off-by: Tien Fong Chee <[email protected]>
|
|
Move duplicated function cm_get_qspi_controller_clk_hz to clock_manager.c.
Signed-off-by: Siew Chin Lim <[email protected]>
Signed-off-by: Tien Fong Chee <[email protected]>
Reviewed-by: Ley Foon Tan <[email protected]>
|
|
Restructure Stratix10 and Agilex handoff code to used by
all SOC64 devices, in preparation to support handoff for
Diamond Mesa.
Remove wrap_pinmux_config_s10.c. Add wrap_handoff_soc64.c
which contains the generic function to parse the handoff
data.
Update system_manager_soc64.c to use generic handoff
function in wrap_handoff_soc64.c.
Signed-off-by: Siew Chin Lim <[email protected]>
Reviewed-by: Ley Foon Tan <[email protected]>
|
|
Rearrange sequence of macros in handoff_soc64.h without any functionality
change. In preparation for Stratix10 and Agilex handoff function
restructuring.
Signed-off-by: Siew Chin Lim <[email protected]>
|
|
Rename handoff_s10.h to handoff_soc64.h. Changed macros prefix from
S10_HANDOFF to SOC64_HANDOFF.
Signed-off-by: Siew Chin Lim <[email protected]>
|
|
Prepare v2021.04-rc4
|
