| Age | Commit message (Collapse) | Author |
|---|
|
A few Rockchip ARMv7 SoCs use 0x60000000 as DRAM base address instead of
the more common 0x0 DRAM base address used on AArch64 SoCs.
Add default options that should work for these ARMv7 SoCs. Same offsets
as before are used, just below 64 MiB. Hex values have also been padded
to improve alignment.
Signed-off-by: Jonas Karlman <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
The stack-pointer addresses used with ROCKCHIP_COMMON_STACK_ADDR expect
that DRAM is initialized by TPL or ROCKCHIP_EXTERNAL_TPL, that SPL has
access to full DRAM and SPL is loaded to/executed from start of DRAM.
Add depends on to ensure use of the ROCKCHIP_COMMON_STACK_ADDR symbol
does not cause problem for any board not using TPL and back-to-BROM
loading of SPL.
Signed-off-by: Jonas Karlman <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
The Kconfig symbol ROCKCHIP_COMMON_STACK_ADDR currently imply the
TPL_ROCKCHIP_COMMON_BOARD option when TPL=y. This is inconvenient for a
SoC with very limited SRAM to use a custom tpl.c together with the
common stack addresses.
Move any imply TPL_ROCKCHIP_COMMON_BOARD to under the SoC symbol, where
it belongs. Add the missing imply to RK3328 and PX30 use a SoC specific
tpl.c and only expect imply TPL_LIBGENERIC_SUPPORT.
Signed-off-by: Jonas Karlman <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
I don't see a reason why this should only be enabled on a per-board
basis. The rng IP is inside the SoC and doesn't seem to rely on anything
external to it, therefore let's enable it on the SoC DTSI and remove the
now empty px30-evb-u-boot.dtsi.
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Nothing is calling the function rk_board_init() and the io-domain driver
can handle the functions intended purpose based on information from DT.
Cleanup by removing the unused rk_board_init() function and re-sort
included headers.
Signed-off-by: Jonas Karlman <[email protected]>
Reviewed-by: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Jiaxun Yang <[email protected]> says:
This is a huge series which promoted MIPS/Boston target into a
usable state, with fixes to drivers and general framework issues
I found in this process.
I also converted the target to OF_UPSTREAM.
This target is covered by QEMU, to test on QEMU:
```
make boston64r6el_defconfig
make
qemu-system-mips64el -M boston -cpu I6500 -bios ./u-boot.bin -nographic
```
Link: https://lore.kernel.org/r/[email protected]
|
|
We can now boot with upstream devicetree.
Reviewed-by: Sumit Garg <[email protected]>
Signed-off-by: Jiaxun Yang <[email protected]>
Reviewed-by: Daniel Schwierzeck <[email protected]>
|
|
This is a PC-like platform board.
Enable drivers for most on-board devices to make it useful.
Signed-off-by: Jiaxun Yang <[email protected]>
Reviewed-by: Daniel Schwierzeck <[email protected]>
|
|
Some drivers need this header.
Provide this dummy header as riscv did.
Signed-off-by: Jiaxun Yang <[email protected]>
Reviewed-by: Daniel Schwierzeck <[email protected]>
|
|
In-line ECC support was added for LPDDR by reserving the last one-eighth
of the memory space for ECC data. Full memory initialization using the
BIST MEM INIT mailbox command, based on address and size, is required to
correctly generate ECC data and enable proper ECC logic verification.
Signed-off-by: Tingting Meng <[email protected]>
|
|
Cache allocation for dirty writes in the CCU system cache was disabled
for performance optimization.
Signed-off-by: Tingting Meng <[email protected]>
|
|
LMB_ARCH_MEM_MAP is enabled, and lmb_arch_add_memory() is introduced to
correctly handle memory reservations for the second and third DDR
memory banks.
Signed-off-by: Tingting Meng <[email protected]>
|
|
MMU mapping regions were added for the second and third DDR memory banks.
Signed-off-by: Tingting Meng <[email protected]>
|
|
As of 2025, Altera is now a standalone company prior to
being a subsidiary of Intel Corporation.
Update CPU info printout naming from Intel to Altera.
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
|
|
Use GPIO hogging method in device tree to set SDIO_SEL pin (portb3)
direction as output with value 0 after power-on reset.
This is to ensure stable 0V voltage reading from SDIO_SEL GPIO pin
after board init.
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
The use of both "imply SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION" and
"imply SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION_TYPE" here is wrong as
those are both part of the same choice statement. Furthermore you cannot
select/imply something from a choice statement, it must be a "default ...
if ..." construct within the choice statement in question.
Signed-off-by: Tom Rini <[email protected]>
|
|
Vendor Authorized Boot flow configurations are enabled for boards
based on Agilex5 SoCFPGA. Also, required changes are made to the
SoCFPGA make file for building and linking relevant secure source
code files.
Signed-off-by: Naresh Kumar Ravulapalli <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Load and entry addresses are corrected for Agilex5 SoCFPGA board
which would enable to generate the kernel itb file with the right
addresses.
Signed-off-by: Naresh Kumar Ravulapalli <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Send out "HPS_STAGE_NOTIFY" mailbox command to the
Secure Device Manager (SDM) in SPL to inform SDM on
FSBL execution.
This is necessary for the SDM to recognize that the
FSBL stage has begun its execution and should be
made as early as possible in the FSBL process.
Therefore, the mailbox will initialize and send out
the notification right after the completion of timer
initialization.
Signed-off-by: Mahesh Rao <[email protected]>
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Enable reset support for FPGA2SDRAM bridge for Stratix10, as well as
FPGA2SoC and SoC2FPGA bridges for all SoC64 families.
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Add reset manager registers in preparation for F2S bridge reset
support as well as the mask support to enable/disable the bridges.
Mask value:
BIT0: soc2fpga
BIT1: lwhps2fpga
BIT2: fpga2soc
These bridges are available only in Stratix10:
BIT3: f2sdram0
BIT4: f2sdram1
BIT5: f2sdram2
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Introducing a new mailbox command "HPS_STAGE_NOTIFY" to notify Secure
Device Manager (SDM) on the stage of HPS code execution.
Generally, there are three main code execution stages: First Stage Boot
Loader (FSBL) which is U-Boot SPL, Second Stage Boot Loader (SSBL) which
is U-Boot, and the Operating System (OS) which is Linux.
This enables the user to query the SDM for HPS error details.
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-at91
Second set of u-boot-at91 features for the 2025.07 cycle:
This feature set includes the addition of sam9x60 usb gadget, and a fix
for sama5d2 SPL.
|
|
MIPS_RELOCATION_TABLE_SIZE=0x8000 is too small to enable UNIT_TEST.
Increase it by 50 % (16 KiB).
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
Since commit f98cd471f06b ("clk: clk-composite: Resolve parent clock by
name") the StarFive VisionFive 2 board fails to boot.
Before that patch the SPL debug UART showed warnings like:
clk_register: failed to get pll0_out device (parent of perh_root)
clk_register: failed to get pll0_out device (parent of qspi_ref_src)
clk_register: failed to get pll0_out device (parent of usb_125m)
clk_register: failed to get pll0_out device (parent of gmac_src)
clk_register: failed to get pll0_out device (parent of gmac1_gtxclk)
clk_register: failed to get pll0_out device (parent of gmac0_gtxclk)
The &pllclk clock needs to be enabled early.
Fixes: f98cd471f06b ("clk: clk-composite: Resolve parent clock by name")
Suggested-by: Marek Vasut <[email protected]>
Tested-by: Yao Zi <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
The PIT timer needs to be available early in the SPL phase,
otherwise SPL fails to boot and only prints:
Could not initialize timer (err -96)
Fix this problem by passing 'bootph-all' to the sama5d2 PIT node.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Enable USB gadget usb0 node support.
Signed-off-by: Zixun LI <[email protected]>
Reviewed-by: Eugen Hristev <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
|
|
Add the USB gadget DT node for the sam9x60 SoC's.
Signed-off-by: Zixun LI <[email protected]>
Reviewed-by: Eugen Hristev <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
|
|
CU_CLKOUT0 can be driven by two input clocks: a 25 MHz and a 50 MHz source.
Currently, the 25 MHz option is not selectable due to an incorrect mux
configuration where the 50 MHz clock is duplicated in the parent list.
This patch fixes the mux setup, allowing proper selection of the 25 MHz
clock source for MCU_CLKOUT0.
Similar configuration is already correctly implemented in AM62 clock
data for 'hsdiv4_16fft_main_2_hsdivout1_clk10', where MCU_CLKOUT0
parent switching behaves as expected.
Link: http://downloads.ti.com/tisci/esd/latest/5_soc_doc/am62px/clocks.html#clocks-for-board0-device
Signed-off-by: Parth Pancholi <[email protected]>
Reviewed-by: Bryan Brattlof <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-microblaze
AMD/Xilinx/FPGA changes for v2025.07-rc1
AMD/Xilinx:
- Synchronize enums around tcm_mode
- Access bootmode registers via firmware interface
- Setup default values for DEBUG_UART
- Fix dfu alt buffer clearing
- Convert loadpdi command to fpga
- Fix board detection code
- Minor defconfig updates
Versal:
- Wire multi_boot register
Versal Gen 2:
- Enable missing drivers
- Wire i2c FRU decoding at start
- Wire saving variables to different locations
- Disable default DEBUG_UART
- Wire USB/UFS boot and fix access via firmware interface
- Minor fixes
ZynqMP/Kria:
- Enable mkfwumdata
- Topic board update
- Enhance binman configurations
- Kria usb update
BuR:
- Add multiple Zynq based boards
cadence_ospi:
- Enable device reset
fpga:
- Add support for loading bitstream for Altera SoCs
|
|
Add SNAND node to Airoha AN7581 EVB DTS to enable support for attached
SNAND flash.
Signed-off-by: Christian Marangi <[email protected]>
|
|
Add eMMC nodes with the fixed regulator and fixed clock. It's also
needed to assign the clock and set it to 200MHz as it's set to 150Mhz by
default.
Signed-off-by: Christian Marangi <[email protected]>
|
|
Add Ethrnet nodes for Airoha AN7581 EVB board.
Signed-off-by: Christian Marangi <[email protected]>
|
|
Add pending Chip SCU node for clock node.
Signed-off-by: Christian Marangi <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-marvell
CI: https://dev.azure.com/sr0718/u-boot/_build/results?buildId=390&view=results
- mvebu_espressobin_ultra-88f3720_defconfig: disable SATA
- helios4: enable ddr odt0 on write for both chip-select
- clearfog,helios4: disable sdhci sdma
- mvebu/bubt: Correct usage of IS_ENABLED() macro
- mvebu: Correct SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR usage
|
|
This commit adds support for the brcp1, brsmarc2, brcp150 and brcp170
boards. This boards are based on the Xilinx Zynq SoC.
Signed-off-by: Bernhard Messerklinger <[email protected]>
Acked-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
u-boot.itb name is coming via CONFIG_SPL_FS_LOAD_PAYLOAD_NAME and it's
change will affect SD boot mode that's why start to use it.
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/0f037e62e2d8486c0f68f204b45705be9e996ba7.1744039048.git.michal.simek@amd.com
|
|
The source code for the versal loadpdi command and the
CONFIG_CMD_VERSAL configuration has been removed. It now utilizes
the fpga load <dev> <address> <length> command to load secure &
non-secure pdi images.
Signed-off-by: Prasad Kummari <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
Add support for loading the secure & non-secure pdi images and PL
bitstream on the Versal Gen2 platform. The FPGA driver is enabled
to load the bitstream in PDI format on the AMD Versal Gen2 device.
PDI is the new programmable device image format for Versal Gen2,
and the bitstream for the Versal Gen2 platform is generated exclusively
in this format.
With the enhanced SMC format in TF-A ensuring transparent payload
forwarding for Versal Gen2, the u-boot driver must now handle the
word swapping of PDI address that was previously done in TF-A for
this API. The source code for the Versal2 loadpdi command and the
CONFIG_CMD_VERSAL2 configuration has been removed. It now utilizes
the fpga load <dev> <address> <length> command to load secure &
non-secure pdi images.
Signed-off-by: Prasad Kummari <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
Add support for loading the secure & non-secure pdi images and
PL bitstream on the Versal NET platform. The FPGA driver is enabled
to load the bitstream in PDI format on the AMD Versal NET device.
PDI is the new programmable device image format for Versal NET,
and the bitstream for the Versal NET platform is generated exclusively
in this format.
The source code for the versalnet loadpdi command and the
CONFIG_CMD_VERSAL_NET configuration has been removed. It now utilizes
the fpga load <dev> <address> <length> command to load secure &
non-secure pdi images.
Signed-off-by: Prasad Kummari <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
Update the firmware driver UFS APIs zynqmp_pm_ufs_* to directly
read/write to the pmc_iou_slcr and efuse_cache registers. Replace
these raw reads/writes with the xilinx_pm_request() API with the
correct arguments once the PM related changes are done.
Signed-off-by: Venkatesh Yadav Abbarapu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/ee2d1ad2e07e96f1948ab6ffe8f3c50a3b8f9be9.1742462001.git.michal.simek@amd.com
|
|
Adjust configuration and devicetree so the topic-miami board actually
boots.
Replace the custom scripting and just use distro_boot. Override the
standard zynq routines.
The board attempts to boot from SD card first, and falls back to booting
UBIFS from the QSPI NOR flash.
Signed-off-by: Mike Looijmans <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
Added extended support for retrieving the PMC muti boot mode
register via the firmware interface, which is preferred when
U-Boot runs in EL2 and cannot directly access PMC registers
via raw reads. Ideally, all secure registers should be accessed
via xilinx_pm_request(). Introduced the secure
zynqmp_pm_get_pmc_multi_boot_reg() call, which uses
xilinx_pm_request() to read the PMC multi boot mode register.
BootROM increments the MultiBoot register (PMC_MULTI_BOOT) read
address offset by 32 KB and retries. For SD and eMMC boot modes,
it can search up to 8191 FAT files for the identification string.
A 13-bit mask (0x1FFF) is applied to PMC_MULTI_BOOT_MASK to obtain
the correct values in BootROM.
Signed-off-by: Prasad Kummari <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
Add the UFS boot mode support and update the boot_targets with
ufs mode. If the UFS device is not accessible from APU and
running this is detected as a warning, as the device is not
accessible.
Signed-off-by: Venkatesh Yadav Abbarapu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
Turn anonymous enum TCM_LOCK/TCM_SPLIT into enum tcm_mode {}, set
TCM_LOCK as 0 and TCM_SPLIT as 1 to match LOCK and SPLIT macros in
mach-zynqmp/mp.c, and unify all the functions and their parameters
on this one single enum tcm_mode {} instead of a mix of bool and u8.
No functional change intended.
Signed-off-by: Marek Vasut <[email protected]>
Tested-by: Love Kumar <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
As the code is today, we get a warning about "select" statements on
"choice" options not doing anything. However, it also works as intended
because SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is the default option
within that choice statement. To guard against future regressions, make
the choice statement in common/spl/Kconfig have an explicit default if
MVEBU_SPL_BOOT_DEVICE_MMC.
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Fix a couple of typos in mach-mvebu/Kconfig.
Signed-off-by: Chris Packham <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Add the necessary header as <common.h> is removed
Signed-off-by: yan wang <[email protected]>
|
|
Much like what was fixed on the AM62x and AM62Px platforms[0]. The
CU_CLKOUT0 has two (25mhz and 50mhz) mux options however the clock
structure incorrectly duplicated the first 50mhz option twice. Fix this
for the AM62A platforms so the 25mhz option is selectable.
[0] https://lore.kernel.org/all/[email protected]/
Reported-by: Parth Pancholi <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
|
|
When FIT image with multiple dtbs are involved for R5 boot process,
R5 SPL starts off with the first instance of dtb to probe the
eeprom, then once we have identified the type of board, invocation
of setup_multi_dtb_fit will replace the gd->fdt_blob with the proper
board dtb match. However, when we do this, two things happen:
a) Prior to the invocation of setup_multi_dtb_fit, as part of the eeprom
discovery process, i2c controller device is already probed and marked
as exclusive with the match of the very first tisci match (from the
original boot dtb). This list is stored in the info->dev_list of the
first probe.
b) When the second dtb is loaded, tisci is probed again (since this is a
new node) and the new info->dev_list is empty.
At this stage, the exclusive devices such as i2c instances used to
probe the board information is left in the old info->dev_list that is
no longer used actively by the system using the replaced dtb.
As a result of this, the cleanup we intend to do with
ti_sci_cmd_release_exclusive_devices is no longer complete and
leaves the instances such as i2c for eeprom marked used as we scan just
the new info->dev_list.
This creates a problem when Device Manager(DM) firmware starts up later
on in the boot process and identifies that this instance of i2c is
already marked active, so it assumes this can no longer be controlled
by software and is marked internally as reserved and HLOS can no
longer control these instances. This defeated the purpose of
ti_sci_cmd_release_exclusive_devices.
NOTE: This scheme works just fine if the FIT has just a single dtb as
the info->dev_list is upto date.
To fix this, let us make ti_sci_cmd_release_exclusive_devices scan the
all registrations of tisci instances and cleanup all exclusive devices
that have ever been registered.
As part of this, change the prototype of release_exclusive_devices to
drop the handle since that has no further meaning now.
Though this issue was identified on AM64-sk, this can be present in
other builds which use multi-fit-dtb for R5 SPL startup.
Fixes: 9566b777ae0a ("firmware: ti_sci: Add a command for releasing all exclusive devices")
Signed-off-by: Nishanth Menon <[email protected]>
Reviewed-by: Dhruva Gole <[email protected]>
Reviewed-by: Neha Malcom Francis <[email protected]>
|
