| Age | Commit message (Collapse) | Author |
|---|
|
These are common for all K3 based boards. Add the common values as
defaults and remove from each board defconfig
Signed-off-by: Andrew Davis <[email protected]>
Reviewed-by: Bryan Brattlof <[email protected]>
|
|
Judith Mendez <[email protected]> says:
This patch series fixes MMC_HS_52 mode in am654_sdhci driver,
as well as HIGH_SPEED_ENA and UHS_MODE_SELECT for HS modes.
Also add TI_COMMON_CMD_OPTIONS to K3 Sitara board a53 defconfigs.
Link: https://www.ti.com/lit/er/sprz574a/sprz574a.pdf
Link: https://lore.kernel.org/r/[email protected]
|
|
Add TI_COMMON_CMD_OPTIONS config options to Sitara K3 boards at
a53 stage since we rely on most of the commands implied for testing
and debugging purposes. Since all commands are now enabled by
default, remove the redundant CMD_* options in the a53 defconfigs.
Also add MMC_REG & MMC_SPEED_MODE_SET useful commands to
TI_COMMON_CMD_OPTIONS.
Signed-off-by: Judith Mendez <[email protected]>
Reviewed-by: Bryan Brattlof <[email protected]>
|
|
SPL_TEXT_BASE is used as the load address for the main domain SPL on k3
platforms.
Since the config value is the same for every board, this patch sets the
value 0x80080000 as default for all 64-bit ARCH_K3, 0x43c00000 as
default for the R5 cores and deletes the instances of SPL_TEXT_BASE in
individual defconfigs.
Signed-off-by: Anshul Dalal <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Add UBIFS support on top of MTD devices by enabling the required
configs.
Signed-off-by: Santhosh Kumar K <[email protected]>
|
|
Siddharth Vadapalli <[email protected]> says:
This series enables USB DFU and USB Mass Storage functionality for
AM62, AM62-LP, AM62A, AM62P and J722S SoCs.
Link: https://lore.kernel.org/r/[email protected]
|
|
The config fragment "am62x_a53_usbdfu.config" which adds USB DFU support
for AM62x SoC is applicable to the AM62Px SoC as well. Hence, include it
in "am62px_evm_a53_defconfig" in order to enable support for USB DFU
flash and boot. Remove those configs from "am62px_evm_a53_defconfig" which
are present in the "am62x_a53_usbdfu.config" config fragment that is being
included.
Signed-off-by: Siddharth Vadapalli <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
Reviewed-by: Roger Quadros <[email protected]>
|
|
Judith Mendez <[email protected]> says:
Some K3 devices like am62x and am64x have a M4 processor in the MCU
voltage domain. This patch series introduces remoteproc M4 driver which
will be used to load firmware into and start the M4 remote core.
This series also adds support for R5F cores on am64x SoCs in patch 2 and
sets up environment to load FW in remote cores in patch 3,4,5.
This patch series also enables remoteproc drivers by default as per what
remoteproc sybsystem is supported per SoC, thus all remoteproc options
are now deleted in configs/* since they are no longer required.
This patch series was tested on am64x EVM, am62x SK, am62ax SK,
am62px SK boards.
Any additional tested by's are welcome since I was not able to
test any additional boards.
Tested by running the following commands in u-boot prompt:
=> setenv dorprocboot 1
=> run boot_rprocs
Link: https://lore.kernel.org/r/[email protected]
|
|
Now that remoteproc configs are enabled by default in Kconfig
files, remove these configs which are no longer needed to be
defined here in configs/.
Signed-off-by: Judith Mendez <[email protected]>
Reviewed-by: Andrew Davis <[email protected]>
|
|
Set CONFIG_NR_DRAM_BANKS to 2 as we have two banks described in the
memory/ node for lower and higher addressible DDR regions.
This allows use of FDT functions from fdt_support.c to set up and fix up
the memory/ node correctly.
Signed-off-by: Neha Malcom Francis <[email protected]>
Signed-off-by: Santhosh Kumar K <[email protected]>
|
|
Make the raw-mode options depend on SPL_SYS_MMCSD_RAW_MODE in a more
direct way. This makes it easier to understand the options with
'make menuconfig'.
There are three different ways of specifying the offset:
- sector offset
- partition number
- partition type
So make these a choice, so it is more obvious what is going on.
Update existing boards to enable SPL_SYS_MMCSD_RAW_MODE where needed.
Reviewed-by: Sean Anderson <[email protected]>
Reviewed-by: Quentin Schulz <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
This is called to set fdtfile based on evm.c code calling ti_set_fdt_env.
Signed-off-by: Manorit Chawdhry <[email protected]>
|
|
Enable on disk, raw capsule update.
Signed-off-by: Jonathan Humphreys <[email protected]>
|
|
Enable MMC UHS support for to allow to enter the UHS
modes for MMC1.
Signed-off-by: Judith Mendez <[email protected]>
Acked-by: Bryan Brattlof <[email protected]>
|
|
Jonathan Humphreys <[email protected]> says:
Set basic settings needed for System Ready IR ACS testing, for several TI SoC
based platforms: AM64, AM62, AM62p, BeaglePlay, J7, and BeagleboneAI.
For AM64, AM62, and AM62p, also includes some config cleanup. Should be no
functional change.
|
|
This is required to pass SystemReadyIR tests.
Signed-off-by: Jonathan Humphreys <[email protected]>
|
|
This is required to pass SystemReadyIR tests.
Signed-off-by: Jonathan Humphreys <[email protected]>
|
|
Signed-off-by: Jonathan Humphreys <[email protected]>
|
|
Enable MMC_SPEED_MODE_SET config option in defconfig to enable
mmc rescan for various Sitara devices.
Signed-off-by: Judith Mendez <[email protected]>
|
|
Introduce the initial configs needed to support the am62px SoC family
Signed-off-by: Bryan Brattlof <[email protected]>
|
