| Age | Commit message (Collapse) | Author |
|---|
|
The 'default' directive should be before 'help'.
Signed-off-by: Simona Toaca <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Add i.MX93 9x9 Quick Start Board support.
- Two ddr scripts included w/o inline ecc feature.
- SDHC/NETWORK/I2C/UART supported
- PCA9450 supported, default over drive mode
- Documentation added.
Signed-off-by: Peng Fan <[email protected]>
|
|
Use the new symbol to refer to any 'SPL' build, including TPL and VPL
Signed-off-by: Simon Glass <[email protected]>
|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <[email protected]>
|
|
The rank setting flow should be updated to support multi
fsp config.
Signed-off-by: Jacky Bai <[email protected]>
Reviewed-by: Ye Li <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
Update the DDR init flow for multi-setpoint support on i.MX93. A new
fsp_cfg struct need to be added in the timing file to store the diff
part of the DDRC and DRAM MR register for each setpoint.
Signed-off-by: Jacky Bai <[email protected]>
Reviewed-by: Ye Li <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
change the ddr saved info to the last 16KB of the OCRAM.
Signed-off-by: Jacky Bai <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Reviewed-by: Ye Li <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
According to DDRPHY errata, the Rank-to-Rank Spacing and tphy_rdcsgap
specification does not include the Critical Delay Difference (CDD) to
properly define the required rank-to-rank read command spacing after
executing PHY training firmware.
Following the errata workaround, at the end of data training, we get
all CDD values through the MessageBlock, then re-configure the DDRC
timing of WWT/WRT/RRT/RWT with comparing MAX CDD values.
Signed-off-by: Ye Li <[email protected]>
Acked-by: Peng Fan <[email protected]>
|
|
Add Kconfig for enabling reference events counter in DDRC performance
monitor by default
Signed-off-by: Ye Li <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
Since i.MX9 uses same DDR PHY with i.MX8M, split the DDRPHY to a common
directory under imx, then use dedicated ddr controller driver for each
iMX9 and iMX8M.
The DDRPHY registers are space compressed, so it needs conversion to
access the DDRPHY address. Introduce a common PHY address remap function
for both iMX8M and iMX9 for all PHY registers accessing.
Signed-off-by: Ye Li <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
