| Age | Commit message (Collapse) | Author |
|---|
|
Remove DECLARE_GLOBAL_DATA_PTR from files where gd is not used, and
drop the unnecessary inclusion of asm/global_data.h.
Headers should be included directly by the files that need them,
rather than indirectly via global_data.h.
Reviewed-by: Patrice Chotard <[email protected]> #STMicroelectronics boards and STM32MP1 ram test driver
Tested-by: Anshul Dalal <[email protected]> #TI boards
Acked-by: Yao Zi <[email protected]> #TH1520
Signed-off-by: Peng Fan <[email protected]>
|
|
In octeontx_smi_probe if an error is detected then memory that was
allocated is not freed. Small refactor of the code to use a common
return and free memory. Also return -ENOMEM for an allocation failure.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
|
|
In nicvf_cq_handler there is a test for !cqe_count which will return if
true so it is guaranteed that cqe_count will true after that point. This
makes the later test for cqe_count redundant so it can be removed.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
|
|
In nicvf_rcv_pkt_handler there is no need to initialise err as it is
assigned to immediately after. Also the test for !pkt will return if
true meaning that pkt is guaranteed to be true after that code block and
so no need to test for it and the redundant test can be removed.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
|
|
These all end up using the no-op prefetch() defined in linux/list.h,
because the only possible real implementation is in
arch/mips/include/asm/processor.h, which is behing
CONFIG_CPU_HAS_PREFETCH which is nowhere defined.
In order to be able to drop that fallback definition from list.h,
first remove all uses.
Signed-off-by: Rasmus Villemoes <[email protected]>
|
|
Add a mask parameter to control the lookup of the PCI region from which
the mapping can be made.
Signed-off-by: Andrew Scull <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Evolve dm_pci_map_bar() to include an offset and length parameter. These
allow a portion of the memory to be mapped and range checks to be
applied.
Passing both the offset and length as zero results in the previous
behaviour and this is used to migrate the previous callers.
Signed-off-by: Andrew Scull <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
clean up octeontx_smi_probe by using the live-tree API.
Signed-off-by: Tim Harvey <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
|
|
The fdt node offset is apparently not set properly when probed
causing no MDIO busses to be found. Fix this by obtaining the
offset.
Signed-off-by: Tim Harvey <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Revert a change that occured between the Marvell SDK-10.1.1.0
and SDK-10.3.1.1 which broke QSMII phy support.
Signed-off-by: Tim Harvey <[email protected]>
|
|
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
At present ofnode is present in the device even if it is never used. With
of-platdata this field is not used, so can be removed. In preparation for
this, change the access to go through inline functions.
Signed-off-by: Simon Glass <[email protected]>
|
|
Several Octeon drivers operate by setting the sequence number of their
device. This should not be needed with the new sequence number setup. Also
it is not permitted. Drop it.
Signed-off-by: Simon Glass <[email protected]>
|
|
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.
The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.
Signed-off-by: Simon Glass <[email protected]>
|
|
Rename this to be consistent with the change from 'platdata'.
Signed-off-by: Simon Glass <[email protected]>
|
|
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <[email protected]>
|
|
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <[email protected]>
|
|
Adds support for Network Interface controllers found on
OcteonTX SoC platforms.
Signed-off-by: Suneel Garapati <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
