| Age | Commit message (Collapse) | Author |
|---|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <[email protected]>
|
|
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <[email protected]>
Acked-by: Michal Simek <[email protected]>
Tested-by: Michal Simek <[email protected]> #microblaze (MANUAL_RELOC)
|
|
As DM_ETH is required for all network drivers, it's now safe to
remove the non-DM_ETH support code.
Signed-off-by: Tom Rini <[email protected]>
|
|
A DM_ETH driver may use phy_connect() towards a PHY address on an MDIO
bus which is not specified in the device tree, as evidenced by:
pfe_eth_probe
-> pfe_phy_configure
-> phy_connect
When this happens, the PHY will have an invalid OF node.
When ar803x_config() runs, it silently fails at ar803x_of_init(), and
therefore, fails to run the rest of the initialization.
This makes MII_BMCR contain what it had after BMCR_RESET (0x8000) has
been written into it by phy_reset(). Since BMCR_RESET is volatile and
self-clearing, the MII_BMCR ends up having a value of 0x0. The further
configuration of this register, which is supposed to be handled by
genphy_config_aneg() lower in ar803x_config(), never gets a chance to
run due to this early error from ar803x_of_init().
As a result of having MII_BMCR as 0, the following symptom appears:
=> setenv ethact pfe_eth0
=> setenv ipaddr 10.0.0.1
=> ping 10.0.0.2
pfe_eth0 Waiting for PHY auto negotiation to complete......... TIMEOUT !
Could not initialize PHY pfe_eth0
Manually writing 0x1140 into register 0 of the PHY makes the connection
work, but it is rather desirable that the port works without any manual
intervention.
Fixes: fe6293a80959 ("phy: atheros: add device tree bindings and config")
Signed-off-by: Vladimir Oltean <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
|
|
The clock ouput frequency is calculated incorrectly for AR8035 due to
wrong masking of priv->clk_25m_reg and priv->clk_25m_mask.
This same issue has been already fixed in the kernel by:
commit b1f4c209d84057b6d40b939b6e4404854271d797
Author: Oleksij Rempel <[email protected]>
Date: Wed Apr 1 11:57:32 2020 +0200
net: phy: at803x: fix clock sink configuration on ATH8030 and ATH8035
The masks in priv->clk_25m_reg and priv->clk_25m_mask are one-bits-set
for the values that comprise the fields, not zero-bits-set.
This patch fixes the clock frequency configuration for ATH8030 and
ATH8035 Atheros PHYs by removing the erroneous "~".
To reproduce this bug, configure the PHY with the device tree binding
"qca,clk-out-frequency" and remove the machine specific PHY fixups.
Fixes: 2f664823a47021 ("net: phy: at803x: add device tree binding")
Signed-off-by: Oleksij Rempel <[email protected]>
Reported-by: Russell King <[email protected]>
Reviewed-by: Russell King <[email protected]>
Tested-by: Russell King <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Apply the same fix in the U-Boot driver.
Tested on a i.MX6 Hummingboard.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Michael Walle <[email protected]>
Tested-by: Tom Rini <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
The two functions are now exactly the same, remove one of them.
Signed-off-by: Michael Walle <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
We can configure the clock output in the device tree. Disable the
hardcoded one in here. This is highly board-specific and should have
never been enabled in the PHY driver.
If bisecting shows that this commit breaks your board it probably
depends on the clock output of your Atheros AR8035 PHY. Please have a
look at doc/device-tree-bindings/net/phy/atheros.txt. You need to set
"clk-out-frequency = <125000000>" because that value was the hardcoded
value until this commit.
Signed-off-by: Michael Walle <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Add support for configuring the CLK_25M pin as well as the RGMII I/O
voltage by the device tree.
By default the AT803x PHYs outputs the 25MHz clock of the XTAL input.
But this output can also be changed by software to other frequencies.
This commit introduces a generic way to configure this output.
Also the PHY supports different RGMII I/O voltages: 1.5V, 1.8V and 2.5V.
An internal LDO is able to provide 1.5V (default) and 1.8V. The 2.5V
option needs an external supply voltage. This commit adds support to
switch the internal LDO to 1.8V.
Signed-off-by: Michael Walle <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Signed-off-by: Michael Walle <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Provide functions to read and write the Atheros debug registers.
Signed-off-by: Michael Walle <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Signed-off-by: Michael Walle <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
The upper bits are all the OUI.
Signed-off-by: Michael Walle <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Debug register 5 contains TX_CLK DELAY at bit 8 and reserved values at
the other bit positions, just like the other PHYs in the family do.
Therefore, it is not necessary to hardcode the reserved values, but
instead simply follow the read-modify-write procedure from the common
function.
Signed-off-by: Vladimir Oltean <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
To eliminate any doubts about the out-of-reset value of the PHY, that
the driver previously relied on.
If bisecting shows that this commit breaks your board you probably have
a wrong PHY interface mode. You probably want the
PHY_INTERFACE_MODE_RGMII_RXID or PHY_INTERFACE_MODE_RGMII_ID mode.
Signed-off-by: Vladimir Oltean <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Also take the opportunity to use the phy_read_mmd and phy_write_mmd
convenience functions.
Signed-off-by: Vladimir Oltean <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Signed-off-by: Vladimir Oltean <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Delete the extraneous write to debug reg 5 that enables Tx delay
When the driver was originally introduced in commit "6027384a phylib:
Add Atheros AR8035 GETH PHY support", the Tx delay was being
unconditionally enabled.
Then during "2ec4d10b phy: atheros: add support for RGMII_ID, RGMII_TXID
and RGMII_RXID", the author did not notice that code for enabling Tx
delay code was already. Therefore, the if condition for Tx delay has
always been useless for this PHY since this commit introduced it.
Prior to this patch, every AR8035 PHY in U-boot had Tx delay enabled.
After this patch, only those who define the interface as RGMII_TXID or
RGMII_ID will. This is to be expected, but will nonetheless break the
setups of those who didn't know they rely on Tx delay implicitly.
Signed-off-by: Vladimir Oltean <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
We want to be able to include some other system headers in phy.h but
that requires us to have included common.h in the top-level first.
Also, common.h includes config.h as the first thing it does, so don't
include it directly.
Series-to: u-boot
Series-cc: Grygorii Strashko <[email protected]>
Seried-cc: ti
Series-process-log: sort, uniq
Cover-letter:
Prepare for net: phy: prevent uclass_eth device "node" field overwriting
Prepare for [1] so that it doesn't break the build for a bunch of
boards. There are a number of reasons this series broke the build
but none of them depend on changes in the series, so fix up those
situations ahead of applying that series.
[1] https://patchwork.ozlabs.org/cover/940104/
END
Signed-off-by: Joe Hershberger <[email protected]>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Zhao Qiang <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
In the current driver implementation, config() callback is common
for AR8035 and AR8031 phy. In config() callback, driver tries to
configure MMD Access Control Register and MMD Access Address Data
Register unconditionally for both phy versions which leads to
auto negotiation failure in AM335x EVMsk second port which uses
AR8031 Giga bit RGMII phy. Fixing this by adding separate config
for AR8031 phy.
Reviewed-by: Sekhar Nori <[email protected]>
Signed-off-by: Mugunthan V N <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
This adds support for internal delay on RX and TX on RGMII interface for the
AR8035 phy.
This is basically the same Linux driver do. Tested on a Zynq Zturn board (for
which u-boot support in is my tree; first patch waiting ML approval)
Signed-off-by: Andrea Merello <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
In commit <a058052c358c> [net: phy: do not read configuration register on
reset], phy_reset() will clear the BMCR register. Bit 12(AUTO_NEGOTIATION)
is cleared too. It causes auto-negotiation timeout error on Atheros's
PHY AR8033.
To fix this problem, genphy_config_aneg() and genphy_restart_aneg()
needs to be called in ar8035_config() to enable and restart
auto-negotiation.
Signed-off-by: Alison Wang <[email protected]>
Acked-by: Stefan Agner <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Commit 08ad9b068afb88 (" ar8031: modify the config func of ar8031 to
ar8021_config") selected 'ar8021_config' as the configuration function
for AR8031.
The correct would be to use 'ar8035_config' instead as AR8031/AR8035
have the same programming model and even share the same phy driver
in the linux kernel: drivers/net/phy/at803x.c.
Tested on a mx6qsabresd and wandboard, which now can work without
any PHY setup code in the board files.
Signed-off-by: Fabio Estevam <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Function "genphy_parse_link()" used "if (mii_reg & BMSR_ANEGCAPABLE)" before,
but used "if (phydev->supported & SUPPORTED_Autoneg)" now.
So assign "phydev->supported" to "phydev->drv->features" for ar8035
to enable autonegotiation. Then removed the genphy_config_aneg() function.
Signed-off-by: Xie Xiaobo <[email protected]>
|
|
ar8031 has the same config steps with ar8021, so change its
config func to ar8021_config instead of genphy_config.
Signed-off-by: Zhao Qiang <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
There was wrong phy_mask for AR8021 device,
so the AR8021 can't be probed correctly.
Changed it from 0x4fffff to 0x4ffff0.
Signed-off-by: Haijun Zhang <[email protected]>
|
|
With this, fixup a trivial build error of get_effective_memsize needing
to be updated in the new board/freescale/p1010rdb/spl.c
Signed-off-by: Tom Rini <[email protected]>
|
|
Function "genphy_parse_link()" used "if (mii_reg & BMSR_ANEGCAPABLE)" before
while "if (phydev->supported & SUPPORTED_Autoneg)" now.
So assign "phydev->supported" to "phydev->drv->features" for ar8031/8033
to enable autonegotiation.
Signed-off-by: Zhao Qiang <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
commit 626ee1e3 "phylib: update atheros ar803x phy"
leads in failing ethernet on the pxm2 board.
Calling genphy_config() instead of ar8021_config(),
which seems for ar8021 phys not ar803x phys, make
it working again.
Signed-off-by: Heiko Schocher <[email protected]>
Cc: Shengzhou Liu <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Use the same masks as used in the kernel:
https://git.kernel.org/cgit/linux/kernel/git/stable/linux-stable.git/tree/drivers/net/phy/at803x.c?id=refs/tags/v3.12.6
With such changes Ethernet is functional on hummingboard solo.
Signed-off-by: Fabio Estevam <[email protected]>
Acked-by: Stefano Babic <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Patch: 306640
|
|
The masks were ignoring the last 4 bits which didn't allow detection differences
between the ar8031 and ar8035.
Signed-off-by: Jon Nettleton <[email protected]>
Signed-off-by: Fabio Estevam <[email protected]>
Patch: 288018
|
|
The both AR8031 and AR8035 belong to Atheros 803x serial PHY.
So the phy id mask of AR8031 is the same to the phy id mask
of AR8035. The right mask value is 0x4fffff.
This patch has been tested on the P1010 and P1023.
Signed-off-by: Chunhe Lan <[email protected]>
Cc: Joe Hershberger <[email protected]>
Patch: 287748
|
|
AR8035 driver will be never applied because of wrong mask for
AR8031 driver. Fix this.
Signed-off-by: Heiko Schocher <[email protected]>
Reported-by: Pavel Nakonechny <[email protected]>
Cc: Andy Fleming <[email protected]>
Cc: Joe Hershberger <[email protected]>
Patch: 276944
|
|
As AR8031 and AR8033 have same PHY ID 0x4dd074, they use the
common driver. Currently AR8031_driver didn't work for AR8033,
hence updated it to have it work on AR8031/AR8033.
Signed-off-by: Shengzhou Liu <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <[email protected]>
|
|
add atheros ar803x phy, used on the upcoming siemens boards.
Signed-off-by: Heiko Schocher <[email protected]>
Cc: Andy Fleming <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Signed-off-by: Xie Xiaobo <[email protected]>
|
|
bootp.c:44:14: warning: symbol 'dhcp_state' was not declared. Should it be static?
bootp.c:45:15: warning: symbol 'dhcp_leasetime' was not declared. Should it be static?
bootp.c:46:10: warning: symbol 'NetDHCPServerIP' was not declared. Should it be static?
arp.c:30:17: warning: symbol 'NetArpWaitReplyIP' was not declared. Should it be static?
arp.c:37:16: warning: symbol 'NetArpTxPacket' was not declared. Should it be static?
arp.c:38:17: warning: symbol 'NetArpPacketBuf' was not declared. Should it be static?
atheros.c:33:19: warning: symbol 'AR8021_driver' was not declared. Should it be static?
net.c:183:7: warning: symbol 'PktBuf' was not declared. Should it be static?
net.c:159:21: warning: symbol 'net_state' was not declared. Should it be static?
ping.c:73:6: warning: symbol 'ping_start' was not declared. Should it be static?
ping.c:82:13: warning: symbol 'ping_receive' was not declared. Should it be static?
tftp.c:53:7: warning: symbol 'TftpRRQTimeoutMSecs' was not declared. Should it be static?
tftp.c:54:5: warning: symbol 'TftpRRQTimeoutCountMax' was not declared. Should it be static?
eth.c:125:19: warning: symbol 'eth_current' was not declared. Should it be static?
Note: in the ping.c fix, commit a36b12f95a29647a06b5459198684fc142482020
"net: Move PING out of net.c" mistakenly carried the ifdef CMD_PING
clause from when it was necessary to avoid warnings when it was embedded
in net.c.
Signed-off-by: Kim Phillips <[email protected]>
|
|
The tsec driver had a bunch of PHY drivers already written. This
converts them all into PHY Lib drivers, and serves as the first
set of PHY drivers for PHY Lib.
While doing that, cleaned up a number of magic numbers (though
not all of them, as PHY vendors like to keep their numbers as
magical as possible). Also, noticed that almost all of the
vitesse/cicada PHYs had the same config/parse/startup functions,
so those have been collapsed into one.
Signed-off-by: Andy Fleming <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
Acked-by: Detlev Zundel <[email protected]>
|
