| Age | Commit message (Collapse) | Author |
|---|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <[email protected]>
|
|
From the ethernet header is not on aligned, because the length
of the ethernet header is 14 bytes.
Therefore, unaligned access must be done here.
Signed-off-by: Jacky Chou <[email protected]>
|
|
There is no need to perform the endian twice here.
Signed-off-by: Jacky Chou <[email protected]>
Reviewed-by: Dan Carpenter <[email protected]>
|
|
The issue occurs the UAF (use-after-free) to cause double free
when do the realloc function for the pointers during the
reinitialization NC-SI process, and it will cause the memory
management occurs error.
So, nullify these pointers after free.
Signed-off-by: Jacky Chou <[email protected]>
|
|
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
Acked-by: Michal Simek <[email protected]>
Tested-by: Michal Simek <[email protected]> #microblaze (MANUAL_RELOC)
|
|
Add the handling of NC-SI ethernet frames, and add a check at the start
of net_loop() to configure NC-SI before starting other network commands.
Signed-off-by: Samuel Mendoza-Jonas <[email protected]>
Signed-off-by: Joel Stanley <[email protected]>
Reviewed-by: Cédric Le Goater <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
|
|
Move this header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
This introduces support for the NC-SI protocol, modelled as a phy driver
for other ethernet drivers to consume.
NC-SI (Network Controller Sideband Interface) is a protocol to manage a
sideband connection to a proper network interface, for example a BMC
(Baseboard Management Controller) sharing the NIC of the host system.
Probing and configuration occurs by communicating with the "remote" NIC
via NC-SI control frames (Ethernet header 0x88f8).
This implementation is roughly based on the upstream Linux
implementation[0], with a reduced feature set and an emphasis on getting
a link up as fast as possible rather than probing the full possible
topology of the bus.
The current phy model relies on the network being "up", sending NC-SI
command frames via net_send_packet() and receiving them from the
net_loop() loop (added in a following patch).
The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent
field definitions.
[0]: https://github.com/torvalds/linux/tree/master/net/ncsi
[1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h
Signed-off-by: Samuel Mendoza-Jonas <[email protected]>
Reviewed-by: Joel Stanley <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
