| Age | Commit message (Collapse) | Author |
|---|
|
Use dev_phys_to_bus() to convert CPU addresses of DMA descriptors
into bus addresses of DMA descriptors. This is necessary on hardware
which does not have 1:1 mapping between CPU and memory addressed by
the DMA. This has no impact on other hardware which does not need
this conversion.
Signed-off-by: Marek Vasut <[email protected]>
|
|
At the very early stage when PHY ID is being auto-detected, the
PHY device is not yet instantiated and rswitch_etha .phydev is
still NULL. Add missing check for this condition and perform C22
fallback access in this PHY ID auto-detection case.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Add support for the Renesas Ethernet Switch3 (RSW3) controller,
present in R-Car Gen5 SoCs such as R-Car X5H (R8A78000). The
hardware offset differences are handled via driver match data.
The driver newly detects whether the switch prot is connected
to xPCS or not, and if so, turns on MIOC bit 3. This is new on
R-Car X5H. GWCKSC register is also programmed only on X5H. The
rest of the operation is identical to RSwitch2.
Signed-off-by: Marek Vasut <[email protected]>
Signed-off-by: Tam Nguyen <[email protected]>
Signed-off-by: Phong Hoang <[email protected]>
Signed-off-by: Thanh Quan <[email protected]>
Signed-off-by: Hai Pham <[email protected]>
|
|
The MPIC_MDC_CLK clock setting value differs between R-Car S4
and R-Car X5H. Parametrize the value in preparation for R-Car
X5H addition into this driver. No functional change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The GWDCBAC0, GWDCBAC1, FWPBFCSDC, CABPIRM register offsets changed
between R-Car S4 and R-Car X5H. Parametrize their offsets in preparation
for R-Car X5H addition into this driver. No functional change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Inline FWRO, CARO, GWRO, TARO, RMRO macros directly into the
follow up register macros. FWRO, CARO, GWRO, TARO are already
zero, drop them. RMRO is 0x1000, increment all registers which
add RMRO by 0x1000 directly. No functional change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The forwarding engine CSD register offset changed between the
R-Car S4 and R-Car X5H. Parametrize this offset in preparation
for R-Car X5H addition into this driver. Clean up the macro
parameter names and make them more obvious. No functional change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The total port counts differ across variants of this IP in
R-Car S4 and R-Car X5H. Parametrize port count in preparation
for R-Car X5H addition into this driver. No functional change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The COMA, ETHA, GWCA offsets differ across variants of this IP in
R-Car S4 and R-Car X5H. Parametrize these offsets in preparation
for R-Car X5H addition into this driver. No functional change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
This IP does support operating MII and SerDes via different ports.
Currently, the driver assumes that MII and SerDes are always bound
together on the same port, but this may not be the case. Implement
support for controlling MII and SerDes separately.
While the change is extensive, the gist of the change is to pass
pointer to the selected port registers to MII or SerDes functions,
depending on which port and operations should be done on that port.
Each combined ETHA instance contains both MII and SerDes register
pointers, which may not point to the same port, and passes those
registers to MII and SerDes functions respectively to control the
MII or SerDes of each port.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The new version of RSwitch3 in Renesas R-Car Gen5 uses multiple
clock to supply the IP. Convert the driver to bulk clock API to
cater for both single clock of R-Car S4 and multiple clock of
R-Car Gen5. No functional change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Empty RX DMA descriptor must contain .die_dt field set to DT_FEMPTY,
because hardware DMA overwrites this field to non-DT_FEMPTY when data
are received, and the .recv callback tests the content of RX descriptor
.die_dt field to determine whether hardware did receive any data and
updated the .die_dt field, and based on that information, receives a
packet or not. Fix the incorrect RX DMA descriptor initialization to
assure the .recv callback always works correctly.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Remove macros which are not used in the driver. No functional change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Fix indent from multiple spaces to tabs, to be consistent with
coding style and the rest of the driver. No functional change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
In rswitch_probe the error detection after the call to devm_clk_get is
very wrong. It checks the value of ret which is uninitialised at that
point. Instead it should be using the macros for including errors into
pointers.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Add support for mapping C22 register access to C45-only PHYs.
This is mainly useful for 'mii info' command, which performs
C22 only access to determine PHY ID and link state and does
not work well with this driver so far.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Implement C22 PHY access support in addition to C45 PHY access
support which is already present. This is used for PHYs which
do not support C45 access or which are C22 only.
The C22 access can be recognized when devad is set to -1 or
0xffffffff hex, which also matches MDIO_DEVAD_NONE macro. Test
for this special devad value and if it is set this way, perform
C22 access, otherwise perform C45 access.
Based on work by LUU HOAI <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
|
|
The Set Station Management Mode : Clause 45 setting of MFF bit in MPSM
register can be done in rswitch_mii_access_c45() once, instead of this
being done before each rswitch_mii_access_c45() call. Deduplicate the
bit setting into rswitch_mii_access_c45(). No functional change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Use clrsetbits_le32() to make this complicated construct simpler.
No functional change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Update the macro indent, replace multiple spaces with tabs proper.
No functional change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Replace enum rswitch_reg with plain #define REGISTER OFFSET macros.
The enum rswitch_reg was not referenced anywhere, so there was no
benefit of keeping it around. Include register block labels. Turn
all register offsets into lowercase hex values. No functional change.
Rename EATDQDC to EATDQDCR, GWTRC to GWTRCR, GWDCC to GWDCCR, FWPC0
to FWPC, FWPBFC to FWPBFCR, FWPBFCSDC to FWPBFCSDCR because there
are both register names which used to be part of this enum and also
macros with the same name, each used for slightly different purpose.
Make sure there is no collission.
Signed-off-by: Marek Vasut <[email protected]>
|
|
In case an rswitch port is described as disabled in DT, do not
register it as ethernet device in U-Boot. This way, such ports
cannot be accessed from U-Boot command line.
Signed-off-by: Marek Vasut <[email protected]>
|
|
TFTP transfers of large files, for example 128 MiB, can sporadically
get stuck and the transfer slows down considerably.
This happens because the TX DMA descriptor in DRAM becomes out of sync
with the view of the TX DMA descriptor content from the CPU side, which
is viewed through the CPU caches. In order to guarantee these two views
are consistent, the cache over TX DMA descriptor that has possibly been
written by the rswitch hardware must first be invalidated, only then can
the descriptor be cleared and updated by the CPU, and finally the cache
over that area must be flushed back into DRAM to make sure the rswitch
hardware has consistent view of the updated descriptor content.
The very first invalidation operation was missing, which led to sporadic
corruption of the TX DMA descriptor. Fix it, add the missing invalidation
operation.
Reported-by: Enric Balletbo i Serra <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
Tested-by: Enric Balletbo i Serra <[email protected]>
|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <[email protected]>
|
|
This patch adds Ethernet Switch support that found on R-Car S4
(r8a779f0) SoC. This is extracted from multiple patches from
downstream BSP, with additional rework of the network device
registration.
Signed-off-by: Hai Pham <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
Signed-off-by: Phong Hoang <[email protected]>
Signed-off-by: Takeshi Kihara <[email protected]>
[Marek: Rework the driver to support all ports via subdrivers.
Split the driver up, add generic PHY framework support.
Generic code clean ups.]
Reviewed-by: Ramon Fried <[email protected]>
|
