| Age | Commit message (Collapse) | Author |
|---|
|
https://source.denx.de/u-boot/custodians/u-boot-microblaze
AMD/Xilinx/FPGA changes for v2026.04-rc1 v2
microblaze:
- Fix spl_boot_list order
versal2:
- Fix EMMC distro boot setup
- Align distro boot variables with memory layout
zynqmp-phy:
- Sync with Linux kernel driver
zynqmp:
- Add verify_auth command
- DT sync
- Add placing variables to FAT/EXT4
- Enable PCIe driver by default
pcie - xilinx-nwl:
- Fix Link down crash
ufs:
- Align clock/reset with DT binding
# -----BEGIN PGP SIGNATURE-----
#
# iHUEABYIAB0WIQSXAixArPbWpRanWW+rB/7wTvUR9QUCaW3p3wAKCRCrB/7wTvUR
# 9VkwAP4jPRALpM34VpTimNe/iwigIx8hAHxbvkUU0oJ/DW6W8AEAhCSL+ydgreuv
# kKCyNiOF1sm8IrOh4TdtMIFn37d4Dwg=
# =AkKK
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 19 Jan 2026 02:22:55 AM CST
# gpg: using EDDSA key 97022C40ACF6D6A516A7596FAB07FEF04EF511F5
# gpg: Can't check signature: No public key
|
|
This change is imported from Linux driver and tested with SM6125 SoC.
Note, the msm8996_phy_cfg struct is same as sdm660_phy_cfg but
qusb2_phy_cfg::se_clk_scheme_default differs only.
Signed-off-by: Biswapriyo Nath <[email protected]>
Reviewed-by: Casey Connolly <[email protected]>
Reviewed-by: Sumit Garg <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Casey Connolly <[email protected]>
|
|
The power on function for the phy only deasserts the reset, so the phy
might be in a weird state that we don't clean up properly.
Assert the reset in probe() so that when we power on we will have the
phy in a clean state.
Reviewed-by: Neil Armstrong <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Casey Connolly <[email protected]>
|
|
For PCIe and DisplayPort, the phy instance represents the controller's
logical lane. Wait for the instance 0 phy's PLL to lock as other
instances will never lock. We do this in xpsgtr_wait_pll_lock so callers
don't have to determine the correct lane themselves.
The original comment is wrong about cumulative wait times. Since we are
just polling a bit, all subsequent waiters will finish immediately.
Signed-off-by: Sean Anderson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
[ Linux commit 235d8b663ab9e6cc13f8374abfffa559f50b57b6 ]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
The phy "type" is just the combination of protocol and instance, and is
never used apart from that. Store the instance directly, instead of
converting to a type first. No functional change intended.
Signed-off-by: Sean Anderson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
[ Linux commit 6959d2367bc3503ac4ba3eb4ec6584a43150d6b3 ]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
Lanes can use other lanes' reference clocks, as determined by refclk.
Use refclk to determine the clock to enable/disable instead of always
using the lane's own reference clock. This ensures the clock selected in
xpsgtr_configure_pll is the one enabled.
For the other half of the equation, always program REF_CLK_SEL even when
we are selecting the lane's own clock. This ensures that Linux's idea of
the reference clock matches the hardware. We use the "local" clock mux
for this instead of going through the ref clock network.
Signed-off-by: Sean Anderson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
[ Linux commit 687d6bccb28238fcfa65f7c1badfdfeac498c428 ]
Fixes: 1d78d683496 ("phy: zynqmp: Add serdes/psgtr driver")
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
Due to limited available frequency ratios, the reference clock rate may
not be exactly the same as the required rate. Allow a small (100 ppm)
deviation.
Signed-off-by: Sean Anderson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
[ Linux commit 76009ee76e05e30e29aade02e788aebe9ce9ffd2 ]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
The devm alloc functions that we have may follow the Linux kernel model
where allocations are (almost always) automatically free()'d. However,
quite often we don't enable, in full U-Boot, the tracking and free()'ing
functionality. This in turn leads to memory leaks because the driver
author expects that since the functions have the same name as in the
Linux Kernel they have the same behavior. In turn we then get
functionally correct commits such as commit 00e1fed93c8c ("firmware:
ti_sci: Fix memory leaks in devm_ti_sci_get_of_resource") that manually
add these calls. Rather than manually tracking allocations and
implementing free()s, rework things so that we follow expectations by
enabling the DEVRES functionality (outside of xPL phases).
This turns DEVRES from a prompted symbol to a symbol that must be
select'd, and we now remove our non-managed alloc/free functions from
outside of xPL builds.
Reviewed-by: Michael Trimarchi <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Add PHY driver for Multi-Protocol PHY present on Renesas R-Car X5H
R8A78000 SoC. Currently, the PHY driver only supports configuring
the MPPHY for ethernet operation.
Signed-off-by: Thanh Quan <[email protected]>
Signed-off-by: Phong Hoang <[email protected]>
Signed-off-by: Hai Pham <[email protected]> #Fix License-Identifier
Signed-off-by: Marek Vasut <[email protected]>
[Marek: Clean up macros, indent, clock and reset handling in probe,
rename the driver and add r8a78000- into compatible string,
update commit message.]
|
|
Add support for the Ethernet Physical Coding Sublayer (PCS) controller
on R-Car Gen5 SoCs, specifically the Renesas R-Car X5H R8A78000.
The controller is based on the SERDES infrastructure used in previous
R-Car generations, with updates for Gen5 register layout and features.
Because majority of this driver is SoC-specific register programming,
the majority of this driver is different enough from R8A779F0 SerDes
driver to justify its own driver. Deduplication of the remaining bits
of code does not yield any improvement.
Signed-off-by: Hai Pham <[email protected]>
Signed-off-by: Phong Hoang <[email protected]>
Signed-off-by: Tam Nguyen <[email protected]>
Signed-off-by: Thanh Quan <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
[Marek: Add missing clk_bulk_disable() in fail path.
Drop always-true aneg_on setting.
Reduce poll delay from 100s to 100ms.
Use bulk reset operations to finalize reset handling.]
|
|
USB3.0 PHY
This patch adds SPL Kconfig option (SPL_PHY_IMX8MQ_USB) for the i.MX8MQ,
i.MX8MP, i.MX95, and i.MX94 USB3.0 PHY driver, allowing the driver to be
compiled and probed in SPL stage.
Signed-off-by: Alice Guo <[email protected]>
|
|
Import the init sequence for the UFS on SM7150.
Signed-off-by: Danila Tikhonov <[email protected]>
Signed-off-by: Jens Reidel <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Casey Connolly <[email protected]>
|
|
The UFS on SM6350 can reuse the SDM845 configuration, just like in
Linux.
Reviewed-by: Neil Armstrong <[email protected]>
Signed-off-by: Luca Weiss <[email protected]>
|
|
This PHY driver is required by USB_EHCI_MSM and not useful on its own.
Rather than have it be a prompted option, it should (and currently is)
select'd by USB_EHCI_MSM. Remove the prompt for this option and then
correct the dependency chain (it must select PHY).
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Casey Connolly <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Casey Connolly <[email protected]>
|
|
Move the SERDES configuration check after clock and reset initialization
and change it from a hard failure to a skip of WIZ initialization. This
allows the driver to probe successfully when the SERDES has been
pre-configured by a previous boot stage (e.g., ROM or SPL).
This approach aligns with how the Linux kernel handles pre-configured
SERDES, where the driver gracefully skips reinitialization rather than
failing to probe.
Signed-off-by: Hrushikesh Salunke <[email protected]>
|
|
This driver cannot link without access to functions that are defined in
files that are only build on some platforms. Express those requirements
in Kconfig as well.
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
In case the PHY exit callback reports failure, reset init_count to 0 anyway,
so the next attempt at PHY initialization might try to reinitialize the PHY
and restore it to normal operation.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Siddharth Vadapalli <[email protected]>
|
|
Prepare v2025.10-rc4
|
|
The Rockchip TypeC glue driver improperly present itself as a UCLASS_PHY
driver, without ever implementing the required phy_ops.
This is something that in special circumstances can lead to a NULL
pointer dereference followed by a SError crash.
Change the glue driver to use UCLASS_NOP to fix this.
Signed-off-by: Jonas Karlman <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
The Rockchip USB2PHY glue driver improperly present itself as a
UCLASS_PHY driver, without ever implementing the required phy_ops.
This is something that in special circumstances can lead to a NULL
pointer dereference followed by a SError crash.
Change the glue driver to use UCLASS_NOP to fix this.
Signed-off-by: Jonas Karlman <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Change to use syscon_regmap_lookup_by_phandle() helper instead of
finding the syscon udevice and making a call to syscon_get_regmap().
No runtime change is expected with this simplication.
Signed-off-by: Jonas Karlman <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
The init ops for Rockchip COMBPHY driver is more complex than it needs
to be, e.g. declaring multiple init functions that only differ in the
error message.
Simplify the init ops based on code from the Linux mainline driver.
This change also ensure that errors returned from combphy_cfg() and
reset_deassert_bulk() is propertly propagated to the caller. No other
runtime change is expected with this simplication.
Signed-off-by: Jonas Karlman <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Generic PHY reference counting helps ensure driver ops for init/exit and
power on/off are called at correct state. For this to work the PHY
driver must initialize PHY-id to a persistent value in of_xlate ops.
The Rockchip COMBPHY driver does not initialize the PHY-id field, this
typically lead to use of unshared reference counting among different
struct phy instances.
Initialize the PHY-id in of_xlate ops to ensure use of shared reference
counting among all struct phy instances.
Signed-off-by: Jonas Karlman <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
With working shared reference counting for Generic PHY ops there is no
need for the Rockchip USBDP PHY driver to keep its own status (reference
counting) handling.
Simplify the init ops now that shared reference counting is working.
This also removes the unused mode_change handling as part of the
simplication.
No runtime change is expected with this simplication.
Signed-off-by: Jonas Karlman <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Generic PHY reference counting helps ensure driver ops for init/exit and
power on/off are called at correct state. For this to work the PHY
driver must initialize PHY-id to a persistent value in of_xlate ops.
The Rockchip USBDP PHY driver does not initialize the PHY-id field, this
typically lead to use of unshared reference counting among different
struct phy instances.
Initialize the PHY-id in of_xlate ops to ensure use of shared reference
counting among all struct phy instances.
E.g. on a ROCK 5B following could be observed:
=> usb start
starting USB...
[...]
Bus usb@fc400000: 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
=> usb reset
resetting USB...
[...]
rockchip_udphy phy@fed90000: cmn ana lcpll lock timeout
rockchip_udphy phy@fed90000: failed to init usbdp combophy
rockchip_udphy phy@fed90000: PHY: Failed to init phy@fed90000: -110.
Can't init PHY1
Bus usb@fc400000: probe failed, error -110
scanning usb for storage devices... 0 Storage Device(s) found
With shared reference counting this is fixed:
=> usb reset
resetting USB...
[...]
Bus usb@fc400000: 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Signed-off-by: Jonas Karlman <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Add support for the PCIe/USB3 combo PHY used in the RK3528 SoC.
Config values are taken from vendor U-Boot linux-6.1-stan-rkr5 tag.
Signed-off-by: Jianwei Zheng <[email protected]>
Signed-off-by: Jonas Karlman <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Add support for the PCIe/USB3/SATA combo PHYs used in the RK3576 SoC.
Config values are taken from vendor U-Boot linux-6.1-stan-rkr5 tag.
Signed-off-by: Jon Lin <[email protected]>
Signed-off-by: Jonas Karlman <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Add support for the USB3.0+DP PHY used in the RK3576 SoC.
Config values are taken from vendor U-Boot linux-6.1-stan-rkr5 tag.
Signed-off-by: Frank Wang <[email protected]>
Signed-off-by: Jonas Karlman <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Add support for the USB2.0 PHYs used in the RK3576 SoC.
Config values are taken from vendor U-Boot linux-6.1-stan-rkr5 tag.
Signed-off-by: Frank Wang <[email protected]>
Signed-off-by: Jonas Karlman <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Fix NULL pointer dereference that happen when rockchip-inno-usb2 clock
enabled before device probe. This early clock enable call happen in process
of parent clock activation added in ac30d90f3367.
Fixes: 229218373c22 ("phy: rockchip-inno-usb2: Add support for clkout_ctl_phy").
Fixes: ac30d90f3367 ("clk: Ensure the parent clocks are enabled while reparenting")
Co-authored-by: Jonas Karlman <[email protected]>
Signed-off-by: Alex Shumsky <[email protected]>
Reviewed-by: Jonas Karlman <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Prepare v2025.10-rc3
|
|
Add initial support for i.MX95 USB.30 PHY, which is similar to
the i.MX8MQ and i.MX8MP USB PHY.
The i.MX95 USB3 PHY has a Type-C Assist block (TCA) consisting of two
functional blocks (XBar assist and VBus assist) and is documented
in the i.MX95 RM Chapter 163.3.8 Type-C assist (TCA) block.
Instead of relying on an external MUX for Type-C plug orientation the
XBar can handle the flip internally.
Add initial support for i.MX95 by:
- allowing the driver to be enabled i.MX95
- resetting the XBar
- configuring the TCA in System Configuration mode (which was determined
to be necessary to enable the PHY in device-mode)
Follow-on support will need to be added to steer the XBar based on
either board design (if only one pair is brought out) or if used with a
Type-C controller.
Signed-off-by: Tim Harvey <[email protected]>
Tested-by: Alice Guo <[email protected]>
|
|
In cdns_torrent_phy_probe the test for too many lanes configured does
not set an error code before taking the error path. This could lead to a
silent failure if the calling code does not detect the error. Add the
code to return -EINVAL in this case.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
|
|
In cdns_sierra_pll_bind_of_clocks the variable 'i' is declared but never
assigned to before its value is used in a dev_err. Replace clk_names[i]
by the name passed to device_bind(), i.e., "pll_mux_clk". With that, the
clk_names[] array is unused and can therefore be removed.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
[jf: update description]
Signed-off-by: Jerome Forissier <[email protected]>
|
|
In comphy_cp110_init_serdes_map in comphy_cp110.c there are two fields
in cfg, comphy_lanes_count and comphy_mux_bitcount, which are fetched
from the FDT blob with fdtdec_get_int which returns an int. These two
fields are then tested for being negative. However the fields are
declared as unsigned so those tests must always fail. Change the
declaration of those fields to be int instead of u32 and the code will
work as expected.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
The limit checks in get_speed_string and get_type_string are off by 1 as
they do not account for the maximum index into an array that can be used
is 1 less than the number of elements in that array. Adjust the limit
checks to allow for this.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
In j721e_wiz_probe the test for too many lanes jumps to the error exit
path without assigning an error code which could lead to calling code
silently ignoring the failure. Set the error code.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
|
|
In keystone_usb_init the return code from psc_enable_module should be
returned as is rather than being negated.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
|
|
In qcom_snps_eusb2_phy_probe after the call to devm_clk_get if an error
is found then ret is printed but has not been assigned to by the code.
Decode the error from the pointer and assign it to ret.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
Reviewed-by: Sumit Garg <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Casey Connolly <[email protected]>
|
|
Add DM driver for Exynos USB PHY controllers. For now it only supports
Exynos850 SoC. Only UTMI+ (USB 2.0) PHY interface is implemented, as
Exynos850 doesn't support USB 3.0. Only two clocks are used for this
controller:
- phy: bus clock, used for PHY registers access
- ref: PHY reference clock (OSCCLK)
Ported from Linux kernel: drivers/phy/samsung/phy-exynos5-usbdrd.c
Signed-off-by: Sam Protsenko <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
Reviewed-by: Minkyu Kang <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
This is a port of the corresponding commit in the Linux kernel which
adds the same support for the Cadence Torrent driver[0]. The commit
message below is taken as-is from the Linux kernel commit being ported.
The Torrent SERDES can support at most two different protocols (PHY types).
This only mandates that the device-tree sub-nodes used to represent the
configuration should describe links with at-most two different protocols.
The existing implementation however imposes an artificial constraint that
allows only two links (device-tree sub-nodes). As long as at-most two
protocols are chosen, using more than two links to describe them in an
alternating configuration is still a valid configuration of the Torrent
SERDES.
A 3-Link 2-Protocol configuration of the 4-Lane SERDES can be:
Lane 0 => Protocol 1 => Link 1
Lane 1 => Protocol 1 => Link 1
Lane 2 => Protocol 2 => Link 2
Lane 3 => Protocol 1 => Link 3
A 4-Link 2-Protocol configuration of the 4-Lane SERDES can be:
Lane 0 => Protocol 1 => Link 1
Lane 1 => Protocol 2 => Link 2
Lane 2 => Protocol 1 => Link 3
Lane 3 => Protocol 2 => Link 4
[0] https://github.com/torvalds/linux/commit/5b7b83a9839be643410c31d56f17c2d430245813
Signed-off-by: Hrushikesh Salunke <[email protected]>
|
|
Enable QMP phy for QCS615, referenced from Linux.
Reviewed-by: Neil Armstrong <[email protected]>
Signed-off-by: Aswin Murugan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Casey Connolly <[email protected]>
|
|
Enable QMP phy for QCS8300, referenced from Linux.
Reviewed-by: Casey Connolly <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
Signed-off-by: Balaji Selvanathan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Casey Connolly <[email protected]>
|
|
E Shattow <[email protected]> says:
Make consistent use of lowercase hexadecimal prefix '0x' throughout U-Boot.
There are a few remaining uses of uppercase 'X' to denote hexadecimal prefix
or placeholder in documentation and error messages.
External devicetree-rebasing dts/upstream and the generated code of
xilinx/zynq are ignored for the series.
Link: https://lore.kernel.org/r/[email protected]
|
|
Use consistent lowercase hex prefix style in drivers/*
Does not change hex prefix case in allcaps uppercase style error messages
Signed-off-by: E Shattow <[email protected]>
|
|
Add private uclass data for "stm32-usbphyc-clk" as it is not done
by the driver model.
This clk struct is needed by CCF to save the unique id used to identify
each clock.
Signed-off-by: Patrick Delaunay <[email protected]>
Signed-off-by: Patrice Chotard <[email protected]>
Cc: Lukasz Majewski <[email protected]>
Cc: Sean Anderson <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
The bitshift in GEM_CLK_CTRL register is five bits, not two. There are
four bits for each GEM, and one bit reserved in between.
This has caused that using more than one GEM is impossible,
additionally corrupting the GEM0's configuration, leaving GEM0
unusable as well (ie. if GEM0 and GEM1 are used, GEM1 configuration is
going to write to GEM0's registers wrong value, leaving GEM0 unusable)
Signed-off-by: Frantisek Bohacek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
So far Allwinner boards controlled the USB OTG ID detection via the
respective GPIO pin specified in Kconfig, as a string. All boards should
have the same GPIO already specified in the devicetree, in the
usb0_id_det-gpios property.
Convert the usage of the Kconfig configured GPIO over to query that
information from the devicetree, then use the existing DM GPIO
infrastructure to request the GPIO.
Only PHY0 supports USB-OTG, so limit the GPIO request to that PHY, to
avoid claiming it multiple times.
This removes the need to name that GPIO in the defconfig file.
Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Jernej Skrabec <[email protected]>
|
|
So far Allwinner boards controlled the USB VBUS detection via the
respective GPIO pin specified in Kconfig, as a string. All boards should
have the same GPIO already specified in the devicetree, in the
usb0_vbus_det-gpios property.
Convert the usage of the Kconfig configured GPIO over to query that
information from the devicetree, then use the existing DM GPIO
infrastructure to request the GPIO.
Only PHY0 supports USB-OTG, so limit the GPIO request to that PHY, to
avoid claiming it multiple times.
This removes the need to name that GPIO in the defconfig file.
Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Jernej Skrabec <[email protected]>
|
|
The device tree binding for the PHY provides VBUS supplies as regulator
references. Now that all boards have the appropriate regulator uclass
drivers enabled, the PHY driver can switch to using them. This replaces
direct GPIO usage, which in some cases needed a special DM-incompatible
"virtual" GPIO from the PMIC.
The following boards provided a value for CONFIG_USB0_VBUS_PIN, but are
missing the "usb0_vbus-supply" property in their device tree. None of
them have the MUSB controller enabled in host or OTG mode, so they
should see no impact:
- Ainol_AW1_defconfig / sun7i-a20-ainol-aw1
- Ampe_A76_defconfig / sun5i-a13-ampe-a76
- CHIP_pro_defconfig / sun5i-gr8-chip-pro
- Cubieboard4_defconfig / sun9i-a80-cubieboard4
- Merrii_A80_Optimus_defconfig / sun9i-a80-optimus
- Sunchip_CX-A99_defconfig / sun9i-a80-cx-a99
- Yones_Toptech_BD1078_defconfig / sun7i-a20-yones-toptech-bd1078
- Yones_Toptech_BS1078_V2_defconfig /
sun6i-a31s-yones-toptech-bs1078-v2
- iNet_3F_defconfig / sun4i-a10-inet-3f
- iNet_3W_defconfig / sun4i-a10-inet-3w
- iNet_86VS_defconfig / sun5i-a13-inet-86vs
- iNet_D978_rev2_defconfig / sun8i-a33-inet-d978-rev2
- icnova-a20-swac_defconfig / sun7i-a20-icnova-swac
- sun8i_a23_evb_defconfig / sun8i-a23-evb
Similarly, the following boards set CONFIG_USB1_VBUS_PIN, but do not
have "usb1_vbus-supply" in their device tree. Neither of them have USB
enabled at all, so again there should be no impact:
- Cubieboard4_defconfig / sun9i-a80-cubieboard4 (also for USB3)
- sun8i_a23_evb_defconfig / sun8i-a23-evb
The following boards use a different pin for USB1 VBUS between their
defconfig and their device tree. Depending on which is correct, they
may be broken:
- Linksprite_pcDuino3_Nano_defconfig (PH11) /
sun7i-a20-pcduino3-nano (PD2)
- icnova-a20-swac_defconfig (PG10) / sun7i-a20-icnova-swac (PH6)
Finally, this board has conflicting pins given for its USB2 VBUS:
- Lamobo_R1_defconfig (PH3) / sun7i-a20-lamobo-r1 (PH12)
Signed-off-by: Samuel Holland <[email protected]>
[Andre: use regulator_set_enable_if_allowed()]
Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Jernej Skrabec <[email protected]>
|
