| Age | Commit message (Collapse) | Author |
|---|
|
This driver adds the base support of pinctrl over SCMI. The driver
does two main things. First, it allows you to configure the initial
pin states. Secondly, it's used a base to build a GPIO driver on
top of it.
To configure the states then add a pinmux config to the scmi_pinctrl
section:
scmi_pinctrl: protocol@19 {
reg = <0x19>;
pinmux1: pinmux_test {
pinmux = <0 1 0xFFFFFFFF 18 1
0 2 0xFFFFFFFF 18 1
0 3 0xFFFFFFFF 18 1>;
function = "f_gpio1";
groups = "grp_1", "grp_3";
};
};
Under linux the pinctrl subsystem will parse the function and group
properties and use that to handle muxing. However, under u-boot the
pin muxing is done using the "pinmux" property, which feeds raw SCMI
pinctrl PINCTRL_SETTINGS_CONFIGURE commands to the server. The
numbers are: selector, identifier, function_id, config_type, and
config_value. In the example above, it sets pins 1, 2, and 3 to 1.
The linux-kernel ignores this pinmux property.
Signed-off-by: Dan Carpenter <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
Although the pinctrl pm requests are implemented in the PMU firmware,
PM_QUERY_DATA is actually implemented in ATF. In SPL (or when running in
EL3), ATF is not yet running, so we need to implement this API
ourselves. Do the bare minimum, allowing SPL to enumerate functions, but
don't bother with groups. Groups take up a lot of space, and can be
emulated with pins. For example, a node like
display-port {
mux {
groups = "dpaux0_1";
function = "dpaux0";
};
};
can be replaced by
display-port {
mux {
pins = "MIO34", "MIO35", "MIO36", "MIO37";
function = "dpaux0";
};
};
While this isn't backwards-compatible with existing devicetrees, it's
more than enough for SPL where we may only need to mux one or two pins.
Add SPL_PINCTRL_ZYNQMP to ensure there's no SPL size growth when pinctrl
is enabled in U-Boot but isn't necessary for SPL. The only config this
would affect is Kria, but SPL_PINCTRL_GENERIC is disabled so
SPL_PINCTRL_ZYNQMP is not selected.
Signed-off-by: Sean Anderson <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The SoC pads of TH1520 are separated into three groups (AP 1, AP 2 and
AON) controlled by independent pin controllers. This patch ports their
driver from Linux kernel with most code for setting pinconf and pinmux
kept as is.
The dt-binding of TH1520 pin controller uses a schema where pins to
configure are specfied as strings and looked up at runtime, which the
generic pinctrl helpers of U-Boot cannot parse, thus a customized
set_state() callback is implemented to parse pinconfig nodes and setup
the configuration.
Signed-off-by: Yao Zi <[email protected]>
Acked-by: Leo Yu-Chi Liang <[email protected]>
|
|
implement a driver to use semtech pinctrl and
gpio expander, this driver is adapted from a
existent linux driver that is written by
Gregory Bean <[email protected]>.
Signed-off-by: Anis Chali <[email protected]>
|
|
It is confusing to have both "$(PHASE_)" and "$(XPL_)" be used in our
Makefiles as part of the macros to determine when to do something in our
Makefiles based on what phase of the build we are in. For consistency,
bring this down to a single macro and use "$(PHASE_)" only.
Signed-off-by: Tom Rini <[email protected]>
|
|
Greg Malysa <[email protected]> says:
This series adds all of the supported peripheral drivers for the sc5xx
series of SoCs from Analog Devices and other drivers that are used by
the evaluation kits, such as a GPIO expander used by the EZLITE carrier
boards. This series passes gitlab CI tests.
Link: https://lore.kernel.org/r/[email protected]
|
|
This adds support for pin configuration on the Analog Devices SC5XX SoC
family. This commit is largely a port of the Linux driver, which has not
yet been submitted upstream.
Co-developed-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Nathan Barrett-Morrison <[email protected]>
Co-developed-by: Ian Roberts <[email protected]>
Signed-off-by: Ian Roberts <[email protected]>
Signed-off-by: Vasileios Bimpikas <[email protected]>
Signed-off-by: Utsav Agarwal <[email protected]>
Signed-off-by: Arturs Artamonovs <[email protected]>
Signed-off-by: Oliver Gaskell <[email protected]>
Signed-off-by: Greg Malysa <[email protected]>
|
|
The RZN1 symbol name is CONFIG_RZN1, there is no CONFIG_ARCH_RZN1.
Since RZN1 enables CONFIG_ARCH_RENESAS as well, remove the special
RZN1 entry from Makefile, the RZN1 pinctrl driver will still be
pulled in via CONFIG_ARCH_RENESAS.
Fixes: e4aea57fa773 ("pinctrl: renesas: add R906G032 driver")
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Paul Barker <[email protected]>
|
|
Use XPL_ as the symbol to indicate an SPL build. This means that SPL_ is
no-longer set.
Signed-off-by: Simon Glass <[email protected]>
|
|
Rename ARCH_RMOBILE to ARCH_RENESAS because all the chips are made
by Renesas, while only a subset of them is from the R-Mobile
line.
Use the following command to perform the rename:
"
$ git grep -l 'ARCH_RMOBILE' | xargs -I {} sed -i 's@ARCH_RMOBILE@ARCH_RENESAS@g' {}
"
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Paul Barker <[email protected]>
|
|
Move the Qualcomm pinctrl drivers out of mach-snapdragon and over to the
rest of the pinctrl drivers, adjust the drivers so that support for each
platform can be enabled/disabled individually and introduce platform
specific configuration options.
Reviewed-by: Sumit Garg <[email protected]>
Signed-off-by: Caleb Connolly <[email protected]>
|
|
The existing pinctrl driver available for Tegra SOC is well
designed, but it lacks DM support. Let's add a DM compatible
overlay, which allows use of the device tree, along with preserving
backward compatibility with all existing setups and the ability
to use it in SPL board configuration stage.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Pinctrl/pinconf driver for Renesas RZ/N1 (R906G032) SoC.
This is quite rudimentary right now, and only supports applying a
default pin configuration as specified by the device tree.
Signed-off-by: Ralph Siemsen <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Add pinctrl driver for StarFive JH7110 SoC.
Signed-off-by: Kuan Lim Lee <[email protected]>
Signed-off-by: Emil Renner Berthing <[email protected]>
Signed-off-by: Jianlong Huang <[email protected]>
Signed-off-by: Yanhong Wang <[email protected]>
Tested-by: Conor Dooley <[email protected]>
|
|
Add Nuvoton BMC NPCM750 Pinmux and Pinconf support.
Signed-off-by: Jim Liu <[email protected]>
|
|
A big part is the DM pinctrl driver, which allows us to get rid of quite
some custom pinmux code and make the whole port much more robust. Many
thanks to Samuel for that nice contribution! There are some more or less
cosmetic warnings about missing clocks right now, I will send the trivial
fixes for that later.
Another big chunk is the mkimage upgrade, which adds RISC-V and TOC0
(secure images) support. Both features are unused at the moment, but I
have an always-secure board that will use that once the DT lands in the
kernel.
On top of those big things we have some smaller fixes, improving the
I2C DM support, fixing some H6/H616 early clock setup and improving the
eMMC boot partition support.
The gitlab CI completed successfully, including the build test for all
161 sunxi boards. I also boot tested on a A64, A20, H3, H6, and F1C100
board. USB, SD card, eMMC, and Ethernet all work there (where applicable).
|
|
Create a do-nothing driver for each sunxi pin controller variant.
Since only one driver can automatically bind to a DT node, since the
GPIO driver already requires a manual binding process, and since the
pinctrl driver needs access to some of the same information, refactor
the GPIO driver to be bound by the pinctrl driver. This commit should
cause no functional change.
Signed-off-by: Samuel Holland <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
Prepare v2022.04-rc5
|
|
"kendryte" is the marketing name for the K210 RISC-V SoC produced by
Canaan Inc. Rather than "kendryte,k210", use the usual "canaan,k210"
vendor,SoC compatibility string format in the device tree files and
use the SoC name for file names.
With these changes, the device tree files are more in sync with the
Linux kernel DTS and drivers, making uboot device tree usable by the
kernel.
Signed-off-by: Damien Le Moal <[email protected]>
Signed-off-by: Niklas Cassel <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
|
|
Add pinctrl driver for Xilinx ZynqMP SOC. This driver is compatible with
linux device tree parameters for configuring pinmux and pinconf.
Signed-off-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/2d7eefa83c8c0129f7243a25de56a289e948f6c6.1645626183.git.michal.simek@xilinx.com
|
|
This driver supports both pin muxing and GPIO support for the
pin control logic found on Apple SoCs.
Signed-off-by: Mark Kettenis <[email protected]>
|
|
The Fully-Programmable Input/Output Array (FPIOA) device controls pin
multiplexing on the K210. The FPIOA can remap any supported function to any
multifunctional IO pin. It can also perform basic GPIO functions, such as
reading the current value of a pin. However, GPIO functionality remains
largely unimplemented (in favor of the dedicated GPIO peripherals).
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
add DM support for parallel I/O ports on QUICC Engine Block
Signed-off-by: Heiko Schocher <[email protected]>
Patch-cc: Mario Six <[email protected]>
Patch-cc: Qiang Zhao <[email protected]>
Patch-cc: Holger Brunck <[email protected]>
Series-changes: 2
- remove RFC
- fixed Codingstyle errors, therefore new patch
powerpc, mpc83xx: fix codingstyle issues for qe_io.c
- moved DM part to drivers/pinctrl
Commit-notes:
Open questions / discussion:
- I let the old none DM based implementation in code
so boards should work with old implementation.
This should be removed if all boards are converted to
DM/DTS.
- Unfortunately linux DTS does not use "pinctrl-"
properties, instead "pio-handle" properties.
Even worser old U-Boot code initializes all pins
defined in "const qe_iop_conf_t qe_iop_conf_tab[]"
table in board code. As linux does the same I decided
to also scan through all subnodes containing "pio-map"
property and initialize them too.
The proper solution would be to check for "pio-handle"
when a device is probed.
END
|
|
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- livetree API (dev_read_...) is used instead of fdt one (fdt...).
- doc/device-tree-bindings/pinctrl/nexell,s5pxx18-pinctrl.txt added.
Signed-off-by: Stefan Bosch <[email protected]>
|
|
Recent Intel SoCs share a pinctrl mechanism with many common elements. Add
an implementation of this core functionality, allowing SoC-specific
drivers to avoid adding common code.
As well as a pinctrl driver this provides a GPIO driver based on the same
code.
Once other SoCs use this driver we may consider moving more properties to
the device tree (e.g. the community info and pad definitions).
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
This patch adds pinctrl support for mt7628, with a file for common pinmux
functions and a file for mt7628 which has additional support for pinconf.
Signed-off-by: Weijie Gao <[email protected]>
|
|
This patch adds pinctrl/GPIO driver for STMicroelectronics
Multi-Function eXpander (STMFX) GPIO expander.
STMFX is an I2C slave controller, offering up to 24 GPIOs.
The driver relies on UCLASS_PINCTRL and UCLASS_GPIO.
Signed-off-by: Patrick Delaunay <[email protected]>
Signed-off-by: Patrice Chotard <[email protected]>
|
|
Use this driver to fit all Rockchip SOCs and to support
the desired pinctrl configuration via DTS.
Signed-off-by: David Wu <[email protected]>
Acked-by: Heiko Stuebner <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
Reviewed-by: Philipp Tomsich <[email protected]>
|
|
This driver supports the pin and gpio controller found in the Ocelot and
Luton SoCs.
The driver was inspired from the pinctrl driver in Linux, but was
simplified and was modified to allow supporting an other SoCs (Luton).
For Ocelot and Luton the controller is the same, only the pins to program
differ.
Signed-off-by: Gregory CLEMENT <[email protected]>
Reviewed-by: Daniel Schwierzeck <[email protected]>
[changed to only descend into mscc/ dependent on CONFIG_PINCTRL_MSCC]
Signed-off-by: Daniel Schwierzeck <[email protected]>
|
|
This patch adds pinctrl support for MT7629 SoC. The IO core found on
the SoC has the registers for pinctrl, pinconf and gpio mixed up in
the same register range. Hence the driver also implements the gpio
functionality through UCLASS_GPIO.
This also creates a common file as there might be other chips that use
the same binding and driver, then being a little more abstract could
help in the long run.
Signed-off-by: Ryder Lee <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <[email protected]>
|
|
The bcm283x family of SoCs have a GPIO controller that also acts as
pinctrl controller.
This patch introduces a new pinctrl driver that can actually properly mux
devices into their device tree defined pin states and is now the primary
owner of the gpio device. The previous GPIO driver gets moved into a
subdevice of the pinctrl driver, bound to the same OF node.
That way whenever a device asks for pinctrl support, it gets it
automatically from the pinctrl driver and GPIO support is still available
in the normal command line phase.
Signed-off-by: Alexander Graf <[email protected]>
|
|
Add PFC pincontrol driver for the Renesas RCar Gen3 R8A7795 and R8A7796
SoCs. This driver uses the PFC pin tables from Linux, thus letting us
share the occassional fixes to those tables. This driver also has a DT
support, so the pinmux is configured from DT instead of the ad-hoc setup
in board file.
This driver is meant to replace the pinmux part of SH_GPIO_PFC driver.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
To enable support for the Armada 37xx pinctrl driver, we need to
change the Kconfig symbol for the Armada 7k/8k pinctrl driver and its
dependencies to distinguish between both platforms and drivers.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Konstantin Porotchkin <[email protected]>
Cc: Nadav Haklai <[email protected]>
|
|
This driver uses Generic Pinctrl framework and is compatible with
the Linux driver for ast2500: it uses the same device tree
configuration.
Not all pins are supported by the driver at the moment, so it actually
compatible with ast2400. In general, however, there are differences that
in the future would be easier to maintain separately.
Signed-off-by: Maxim Sloyko <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This originally started out as
"pinctrl: Kconfig: reorder to keep Rockchip options together"
and tried to keep the Rockchip-related config options together.
However, we now rewrite all chip-specific driver selections to start
with CONFIG_PINCTRL_ (with the inadvertent changes to related
Makefiles) and sort those alphabetically. And as this already means
touching most of the file, we also reformat the help text to not exceed
80 characters (but make full use of those 80 characters).
Signed-off-by: Philipp Tomsich <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
AT91 PIO controller is a combined gpio-controller, pin-mux and
pin-config module. The peripheral's pins are assigned through
per-pin based muxing logic.
Each SoC will have to describe the its limitation and pin
configuration via device tree. This will allow to do not need
to touch the C code when adding new SoC if the IP version is
supported.
Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This patch adds a pin controller driver supporting devices
using a single configuration register per pin.
Signed-off-by: Felix Brack <[email protected]>
|
|
This driver uses the same pin control binding as that of linux, binding
document of this patch is copied from linux. One addition done is for
GPIO input and output mode configuration which was missing.
Signed-off-by: Vikas Manocha <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add STMicroelectronics STiH410 pinctrl driver
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add a DM port of Marvell pin control driver.
The A8K SoC family contains several silicone dies interconnected
in a single package. Every die is normally equipped with its own
pin controller unit.
There are 2 pin controllers in A70x0 SoC and 3 in A80x0 SoC.
Signed-off-by: Konstantin Porotchkin <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Nadav Haklai <[email protected]>
Cc: Neta Zur Hershkovits <[email protected]>
Cc: Omri Itach <[email protected]>
Cc: Igal Liberman <[email protected]>
Cc: Haim Boot <[email protected]>
Cc: Hanna Hawa <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Add a pin controller driver for Meson GXBB adapted from Linux kernel.
Signed-off-by: Beniamino Galvani <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
AT91 PIO4 controller is a combined gpio-controller, pin-mux and
pin-config module. The peripheral's pins are assigned through
per-pin based muxing logic.
The pin configuration is performed on specific registers which
are shared along with the gpio controller. So regard the pinctrl
device as a child of atmel_pio4 device.
Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Andreas Bießmann <[email protected]>
|
|
Add pinctrl driver support for Samsung's Exynos7420 SoC. The changes
have been split into Exynos7420 specific and common Exynos specific
portions so that this implementation is reusable on other Exynos
SoCs as well.
The Exynos pinctrl driver supports only device tree based pin
configuration. The bindings used are similar to the ones used in the
linux kernel.
Cc: Masahiro Yamada <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Minkyu Kang <[email protected]>
Signed-off-by: Thomas Abraham <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Acked-by: Minkyu Kang <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
This is a simple pinctrl driver, it just support uart and spi pin-mux now.
Signed-off-by: Wills Wang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
[fixed typo in commit subject line]
Signed-off-by: Daniel Schwierzeck <[email protected]>
|
|
CONFIG_PINCTRL_UNIPHIER is more suitable than CONFIG_ARCH_UNIPHIER
to guard the drivers/pinctrl/uniphier directory.
The current CONFIG_PINCTRL_UNIPHIER_CORE is a bit long, so rename it
into CONFIG_PINCTRL_UNIPHIER.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Introduce pinctrl for i.MX6
1. pinctrl-imx.c is for common usage. It's used by i.MX6/7.
2. Add PINCTRL_IMX PINCTRL_IMX6 Kconfig entry.
3. To the pinctrl_ops implementation, only set_state is implemented.
To i.MX6/7, the pinctrl dts entry is as following:
&iomuxc {
pinctrl-names = "default";
pinctrl_csi1: csi1grp {
fsl,pins = <
MX6UL_PAD_CSI_MCLK__CSI_MCLK 0x1b088
MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK 0x1b088
MX6UL_PAD_CSI_VSYNC__CSI_VSYNC 0x1b088
>;
};
[.....]
};
there is no property named function or groups. So pinctrl_generic_set_state
can not be used here.
5. This driver is a simple implementation for i.mx iomux controller,
only parse the fsl,pins property and write value to registers.
6. With DEBUG enabled, we can see log when "i2c bus 0":
"
set_state_simple op missing
imx_pinctrl_set_state: i2c1grp
mux_reg 0x14c, conf_reg 0x3bc, input_reg 0x5d8, mux_mode 0x0, input_val 0x1, config_val 0x4000007f
write mux: offset 0x14c val 0x10
select_input: offset 0x5d8 val 0x1
write config: offset 0x3bc val 0x7f
mux_reg 0x148, conf_reg 0x3b8, input_reg 0x5d4, mux_mode 0x0, input_val 0x1, config_val 0x4000007f
write mux: offset 0x148 val 0x10
select_input: offset 0x5d4 val 0x1
write config: offset 0x3b8 val 0x7f
"
this means imx6 pinctrl driver works as expected.
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
In PIC32 pin-controller is a combined gpio-controller, pin-mux and
pin-config module. Remappable peripherals are assigned pins through
per-pin based muxing logic. And pin configuration are performed on
specific port registers which are shared along with gpio controller.
Note, non-remappable peripherals have default pins assigned thus
require no muxing.
Signed-off-by: Purna Chandra Mandal <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Daniel Schwierzeck <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one. This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.
Cc: Kate Stewart <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
The core support for the pinctrl drivers for all the UniPhier SoCs.
Signed-off-by: Masahiro Yamada <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
