| Age | Commit message (Collapse) | Author |
|---|
|
We are going to add pinctrl data support for both i.MX93 and i.MX91.
Since these SoCs share the same pinctrl driver structure, rename
pinctrl-imx93.c to a more generic pinctrl-imx9.c and update all related
variable and function names accordingly.
This prepares the driver for supporting additional i.MX9 family SoCs.
Signed-off-by: Peng Fan <[email protected]>
|
|
This patch provides a pinctrl driver based on SCMI pin control protocol.
Currently, only the PINCTRL_CONFIG_SET command is implemented.
Signed-off-by: Ranjani Vaidyanathan <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
Signed-off-by: Alice Guo <[email protected]>
Reviewed-by: Ye Li <[email protected]>
|
|
Split MMIO accessors into pinctrl-imx-mmio.c and build this
file only if Kconfig symbol PINCTRL_IMX_MMIO is selected.
Select PINCTRL_IMX_MMIO Kconfig symbol for all but pinctrl-imx8.c
driver, which does not use the MMIO accessors. This reduces the
amount of code compiled on platforms which do not use the code.
No functional change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The only user of the SCU pinctrl code is pinctrl-imx8.c , fold
the entire pinctrl-scu.c code into pinctrl-imx8.c and remove the
matching Kconfig symbols and Makefile entries. No functional change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Add the pinctrl driver and pinfunc header file to support iMX93
Signed-off-by: Peng Fan <[email protected]>
|
|
Add pinctrl driver for i.MX8ULP
Signed-off-by: Ye Li <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
Add i.MXRT pinctrl driver.
Signed-off-by: Giulio Benetti <[email protected]>
|
|
The code responsible for setting proper values in the MUX registers
(in the mxs_pinctrl_set_state()) has been ported from Linux kernel
- SHA1: 17bb763e7eaf tag v5.1.11 from linux-stable.
As the pinctrl node in the imx28.dtsi file has gpio pins nodes as subnodes,
it was necessary to use 'dm_scan_fdt_dev()' (as a .bind method) to also
make them 'visible' by the DM's "gpio_mxs" driver.
Signed-off-by: Lukasz Majewski <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Add i.mx8m pinctrl driver.
Signed-off-by: Peng Fan <[email protected]>
|
|
This implementation comply with other iMX devices pinctrl drivers already
available in U-boot.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
Add pinctrl driver for i.MX8. The pads configuration is controlled
by SCU, so need to ask SCU to configure pads through scfw API.
Add pinctrl-scu to invoke sc_pad_set to configure pads.
Add a new flag IMX8_USE_SCU to differentiate i.MX8 from other platforms
which could directly configure pads from Acore side.
Add CONFIG_PINCTRL_IMX8 as the built gate.
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Anatolij Gustschin <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
Add i.MX7ULP pinctrl driver.
Select CONFIG_PINCTRL_IMX7ULP to use this driver.
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by : Stefano Babic <[email protected]>
|
|
Add CX9020 board based on mx53loco.
Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse
serial_mxc with DTE and prepare for device tree migration of other
functions and imx53 devices.
The CX9020 differs from i.MX53 Quick Start Board by:
- use uart2 instead of uart1
- DVI-D connector instead of VGA
- no audio
- CCAT FPGA connected to emi
- enable rtc
Signed-off-by: Patrick Bruenn <[email protected]>
|
|
Introudce i.MX7 pinctrl driver support.
For now only i.MX7D supported.
There are two iomux controllers in i.MX7D, iomuxc and iomuxc_lpsr.
To iomuxc_lpsr, ZERO_OFFSET_VALID is set, means offset of mux_reg
and conf_reg can begin at 0.
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Introduce pinctrl for i.MX6
1. pinctrl-imx.c is for common usage. It's used by i.MX6/7.
2. Add PINCTRL_IMX PINCTRL_IMX6 Kconfig entry.
3. To the pinctrl_ops implementation, only set_state is implemented.
To i.MX6/7, the pinctrl dts entry is as following:
&iomuxc {
pinctrl-names = "default";
pinctrl_csi1: csi1grp {
fsl,pins = <
MX6UL_PAD_CSI_MCLK__CSI_MCLK 0x1b088
MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK 0x1b088
MX6UL_PAD_CSI_VSYNC__CSI_VSYNC 0x1b088
>;
};
[.....]
};
there is no property named function or groups. So pinctrl_generic_set_state
can not be used here.
5. This driver is a simple implementation for i.mx iomux controller,
only parse the fsl,pins property and write value to registers.
6. With DEBUG enabled, we can see log when "i2c bus 0":
"
set_state_simple op missing
imx_pinctrl_set_state: i2c1grp
mux_reg 0x14c, conf_reg 0x3bc, input_reg 0x5d8, mux_mode 0x0, input_val 0x1, config_val 0x4000007f
write mux: offset 0x14c val 0x10
select_input: offset 0x5d8 val 0x1
write config: offset 0x3bc val 0x7f
mux_reg 0x148, conf_reg 0x3b8, input_reg 0x5d4, mux_mode 0x0, input_val 0x1, config_val 0x4000007f
write mux: offset 0x148 val 0x10
select_input: offset 0x5d4 val 0x1
write config: offset 0x3b8 val 0x7f
"
this means imx6 pinctrl driver works as expected.
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
