| Age | Commit message (Collapse) | Author |
|---|
|
The U_BOOT_DRIVER macro creates a list of drivers used at link time, and
all entries here must be unique. This in turn means that all entries in
the code should also be unique in order to not lead to build failures
later with unexpected build combinations. Typically, the problem we have
here is when a driver is obviously based on another driver and didn't
update this particular field and so while the name field reflects
something unique the linker entry itself is not. In a few places this
provides a more suitable string name as well, however.
Reviewed-by: Marek Vasut <[email protected]>
Reviewed-by: Svyatoslav Ryhel <[email protected]> # Tegra
Reviewed-by: Peter Robinson <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
A few pinctrl drivers cannot build without access to some platform
specific header files. Express those requirements in Kconfig as well.
Signed-off-by: Tom Rini <[email protected]>
|
|
UART-A can be exposed through uSD, this was tested on Transformer T20
but should work on all Ventana-based boards.
TX is exported on SDD pingroup corresponding to uSD CLK pin
RX is exported on SDB which is CMD pin in uSD slot
Signed-off-by: Artur Kowalski <[email protected]>
Reviewed-by: Svyatoslav Ryhel <[email protected]>
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Applies same logic to general Tegra pincontrol driver as is done to Tegra20
by commit:
a35bf832d70 ("pinctrl: tegra20: detect unknown/invalid pin/func
configurations")
Suggested-by: Artur Kowalski <[email protected]>
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Tegra20 driver doesn't know about some pin configurations and even about
some pins. In case when pin configuration is unknown the pin would be
muxed to whatever is under function 0, in case when pin itself is
unknown, it could cause out-of-bounds array access in pinmux_set_func
and pinmux_set_pullupdown.
Signed-off-by: Artur Kowalski <[email protected]>
Reviewed-by: Svyatoslav Ryhel <[email protected]>
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
The current default pin and drive values were more of temporary
placeholders. They have to be replaced with accurate default values as
specified in the TRM and header file.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Tegra 124 is fully compatible with existing Tegra pincontrol
driver, but it needs a specific MIPI PAD control pinconfig.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Pin detection on t20 depends on node name. With recent changes
in node naming, let's remove '_' to be safe about both '_' or
'-' use.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Assorted Tegra enhancements. Merged with the recent XPL_BUILD changes,
resolve some whitespace issues and fix the name of the new apalis-tk1
env file by Tom.
Signed-off-by: Tom Rini <[email protected]>
|
|
Tegra 3 has UART-E exposable via SD card slot which may be
handy for debugging. This change only adds funcmux part, to
use UART-E on the device you additionally would need:
- set stdout-path to serial@70006400 (uarte)
- configure sdmmc1_dat3_py4 and sdmmc1_dat2_py5 pinmux for
uarte
- disable or remove sdhci@7800000 node
- enable CONFIG_TEGRA_ENABLE_UARTE in defconfig
- set CFG_SYS_NS16550_COM to NV_PA_APB_UARTE_BASE in device
header
Signed-off-by: Jonas Schwöbel <[email protected]>
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Use the new symbol to refer to any 'SPL' build, including TPL and VPL
Signed-off-by: Simon Glass <[email protected]>
|
|
Drop all duplicate newlines. No functional change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Reviewed-by: Peter Robinson <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Move all existing pinmux and funcmux code into a dedicated folder in
pinctrl to simplify further maintenance.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
The existing pinctrl driver available for Tegra SOC is well
designed, but it lacks DM support. Let's add a DM compatible
overlay, which allows use of the device tree, along with preserving
backward compatibility with all existing setups and the ability
to use it in SPL board configuration stage.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
