| Age | Commit message (Collapse) | Author |
|---|
|
Add Renesas R-Car R8A78000 X5H MDLC power domain and reset driver,
which serves as a remap driver between DT power domain and reset IDs
and SCMI power domain and reset IDs in case U-Boot runs on Cortex-A,
and as a direct hardware access driver for RSIP.
The R-Car X5H SCP firmware uses different SCMI power domain and
reset IDs in different versions of the SCP firmware, which makes
this remapping necessary. The SCMI base protocol version is updated
for each new SCP firmware version, it is therefore possible to
determine which SCP firmware version is running on the platform
from the base protocol and then determine which remapping table to
use for DT power domain and reset ID to SCMI power domain and reset
ID remapping.
Currently supported versions are SCP 4.28, 4.31, 4.32 .
The DT power domain and reset ID to SCMI power domain and reset ID
remap and call mechanism is simple. Unlike SCMI clock protocol driver,
the SCMI reset and power domain protocol drivers register only a single
device. This driver looks up that single device, obtains its reset or
power domain ops, sets up struct reset_ctl or struct power_domain with
remapped SCMI ID, and invokes operations directly on the device.
In case of RSIP, all power domains are already enabled by BootROM or
early SoC initialization code, the driver therefore only acts as a
stub for the power domain part. The reset part operates as a direct
hardware access reset driver.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Added support for Qualcomm RPMH power domain driver, responsible
for managing power domains on Qualcomm SoCs. This is a port of
the Linux RPMHPD driver [1] and sa8775p related changes. The
power domain driver currently has support to power on and off
MMCX power domain of sa8775p; support for other soc entries power
domains are stubbed, in future, the required soc support can be
added.
[1]:
https://web.git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/pmdomain/qcom/rpmhpd.c?id=3d25d46a255a83f94d7d4d4216f38aafc8e116b
Reviewed-by: Neil Armstrong <[email protected]>
Signed-off-by: Balaji Selvanathan <[email protected]>
Signed-off-by: Aswin Murugan <[email protected]>
Reviewed-by: Sumit Garg <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Casey Connolly <[email protected]>
|
|
TARGET namespace is for machines / boards / what-have-you that
building U-Boot for. Simply replace from TARGET to ARCH
make things more clear and proper for ALL SoCFPGA.
Signed-off-by: Brian Sune <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
# Conflicts:
# drivers/ddr/altera/Makefile
|
|
Upstream DT uses simple-pm-bus instead of simple-bus. simple-pm-bus
requires power domain support. On am33xx, PRM manages power domains but
all domains are enabled at boot. Add stub driver with custom of_xlate
that expects no argumetns to allow simple-pm-bus and dependent devices
to probe.
Signed-off-by: Markus Schneider-Pargmann (TI.com) <[email protected]>
|
|
Some drivers which depend on SoCFPGA specific headers had not had
appropriate dependencies list in Kconfig. Add ARCH_SOCFPGA or
TARGET_SOCFPGA_SOC64 where appropriate.
Signed-off-by: Tom Rini <[email protected]>
|
|
Agilex5 FSBL is required to disable the power of unused peripheral SRAM
blocks to reduce power consumption.
Introducing a new power manager driver for Agilex5 which will be called
as part of Agilex5 SPL initialization process.
This driver will read the peripheral handoff data obtained from the
bitstream and will power off the specified peripheral's SRAM from the
handoff data values.
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
This block delivers power and clocks to the whole display and rendering
pipeline.
Signed-off-by: Miquel Raynal <[email protected]>
|
|
Add power domain driver based on SCMI power domain management protocol.
Signed-off-by: AKASHI Takahiro <[email protected]>
|
|
This patch adds Power controller driver support for Amlogic
A1 family using secure monitor calls. The power domains register
only can access in secure world.
Signed-off-by: Alexey Romanov <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Add trivial driver for i.MX8MP HSIOMIX handling. This is responsible
for enabling the GPCv2 power domains and clock for USB 3.0 and PCIe
in the correct order. Currently supported is the USB 3.0 part which
can be tested, PCIe support should be easy to add.
Tested-By: Tim Harvey <[email protected]> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
This driver is the only SMCCC dependency in iMX8M U-Boot port. Rework
the driver based on Linux GPCv2 driver to directly control the GPCv2
block instead of using SMCCC calls. This way, U-Boot can operate the
i.MX8M power domains without depending on anything else.
This is losely based on Linux GPCv2 driver. The GPU, VPU, MIPI power
domains are not supported to save space, since they are not useful in
the bootloader. The only domains kept are ones for HSIO, PCIe, USB.
Tested-By: Tim Harvey <[email protected]> #imx8mp-venice-defconfig
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
Driver should be enabled by CONFIG_POWER_DOMAIN=y and
CONFIG_ZYNQMP_POWER_DOMAIN=y. Power domain driver doesn't have own DT node
but it uses zynqmp firmware DT node that's why there is a need to bind
driver when firmware node is found.
Driver itself is simple. It is sending pmufw config object overlay for
enabling access to device which is done in ...domain_request().
In ...domain_on() capabilities are passed and node is requested.
This should be bare minimum of required to get power domain driver working.
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
Link: https://lore.kernel.org/r/f4b9433b91c0b18c375b061c7a4e29d428f70547.1644226055.git.michal.simek@xilinx.com
|
|
This driver supports power domains for the power management
controller found on Apple SoCs.
Signed-off-by: Mark Kettenis <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Normally, power domains are handled via TI-SCI in K3 SoCs. However,
SPL is not going to have access to sysfw resources, so it must control
them directly. Add driver for supporting this.
Signed-off-by: Tero Kristo <[email protected]>
Signed-off-by: Tero Kristo <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
|
|
Based on the 54ecb8f7028c ("Linux 5.4-rc1") Everything-Else power domain
driver for Amlogic SoCs.
This driver handles the VPU Power domain and other domains from the
Everything-Else part of the SM1 and G12A SoCs.
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Add support for the power domain controller that's used on the
i.MX8MQ. This will be needed to be able to power on the PCIe
controller. Bindings taken from Linux, driver implementation
taken from the i.MX8 power domain controller and adjusted for
the i.MX8M SoC.
Signed-off-by: Patrick Wildt <[email protected]>
|
|
MESON_GX_VPU_POWER_DOMAIN should depend on POWER_DOMAIN.
Signed-off-by: Maxime Jourdan <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
Reviewed-by: Anatolij Gustschin <[email protected]>
|
|
This adds a power domain driver for the Mediatek SCPSYS unit.
The System Control Processor System (SCPSYS) has several power
management related tasks in the system. The tasks include thermal
measurement, dynamic voltage frequency scaling (DVFS), interrupt
filter and lowlevel sleep control. The System Power Manager (SPM)
inside the SCPSYS is for the MTCMOS power domain control.
For now this driver only adds power domain support.
Signed-off-by: Ryder Lee <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add the power domain DM driver for i.MX8, that it depends on the DTB
power domain trees to generate the power domain provider devices. Users
need to add power domain trees with property "compatible = "nxp,imx8-pd";"
When power on a PD device, the driver will power on its ancestor PD
devices in power domain tree.
When power off a PD device, the driver will check its child PD devices
first. Only if all child PD devices are off, then power off the current PD
device. Then the driver checks sibling PD devices. If sibling PD devices
are off, then it will power off parent PD device.
There is no counter maintained in this driver, but a state to hold current
on/off state. So the request and free functions are empty.
The power domain implementation in i.MX8 DTB set the "#power-domain-cells"
to 0, so there is no ID binding with each PD device. We don't use "id"
variable in struct power_domain. At the same time, we have to set of_xlate
to empty to bypass standard of_xlate in uclass driver.
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Anatolij Gustschin <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
Some TI Keystone 2 and K3 family of SoCs contain a system controller
(like the Power Management Micro Controller (PMMC) on 66AK2G SoCs and
the Device Management and Security Controller on AM65x SoCs) that manage
the low-level device control (like clocks, resets etc) for the various
hardware modules present on the SoC. These device control operations are
provided to the host processor OS through a communication protocol
called the TI System Control Interface (TI SCI) protocol.
This patch adds a power domain driver that communicates to the system
controller over the TI SCI protocol for performing power management of
various devices present on the SoC. Various power domain functionalities
are achieved by the means of different TI SCI device operations provided
by the TI SCI framework.
This code is loosely based on the drivers/soc/ti/ti_sci_pm_domains.c
driver of the Linux kernel.
Reviewed-by: Tom Rini <[email protected]>
Signed-off-by: Andreas Dannenberg <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
|
|
The Amlogic Meson SoCs embeds a specific Power Domain dedicated to the
Video Processing Unit.
This patch implements support for this power domain in preparation of the
future support for the Video display support in U-Boot.
This driver will depend on changes in the clock driver to handle the setup
of the VPU and VAPB clocks configured from DT using assigned-clocks entries.
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
|
|
This allows controlling MISC IDDQ register on BCM6328 SoCs.
Signed-off-by: Álvaro Fernández Rojas <[email protected]>
|
|
In Tegra186, SoC power domains are manipulated using IPC requests to
the BPMP (Boot and Power Management Processor). This change implements a
driver that does that.
Signed-off-by: Stephen Warren <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Many SoCs allow power to be applied to or removed from portions of the SoC
(power domains). This may be used to save power. This API provides the
means to control such power management hardware.
Signed-off-by: Stephen Warren <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
