| Age | Commit message (Collapse) | Author |
|---|
|
Add a new regulator driver for MT6359P and similar PMIC chips.
The MT6359P is a eco version for MT6359 regulator. For the MT8391
platform, we use the MT6359P (MT6365) as the main PMIC. The MT6359 and
MT6359P have different register maps. Therefore, on the MT8391 platform,
we only provide support for the MT6359P. If support for the MT6359 PMIC
it can be added later.
Signed-off-by: Bo-Chen Chen <[email protected]>
Signed-off-by: David Lechner <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
Add a driver for the power regulators of the MediaTek MT6357 PMIC chip.
Signed-off-by: Julien Masson <[email protected]>
Co-developed-by: Macpaul Lin <[email protected]>
Signed-off-by: Macpaul Lin <[email protected]>
Signed-off-by: David Lechner <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
Added a new regulator driver for the MAXIM MAX8907 PMIC, providing
essential regulator functionalities and incorporated the necessary binding
framework within the core PMIC driver.
Tested-by: Ion Agorria <[email protected]>
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
AXP PMICs have a pin which can either report the USB VBUS state, or
driving a regulator that supplies USB VBUS. Add a regulator driver for
controlling this pin. The selection between input and output is done via
the x-powers,drive-vbus-en pin on the PMIC (parent) node.
Signed-off-by: Samuel Holland <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Jernej Skrabec <[email protected]>
|
|
The driver provides regulator set/get voltage and enable/disable functions
for CPCAP PMIC.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Tom Rini <[email protected]> says:
This series switches to always using $(PHASE_) in Makefiles when
building rather than $(PHASE_) or $(XPL_). It also starts on documenting
this part of the build, but as a follow-up we need to rename
doc/develop/spl.rst and expand on explaining things a bit.
Link: https://lore.kernel.org/r/[email protected]
|
|
It is confusing to have both "$(PHASE_)" and "$(XPL_)" be used in our
Makefiles as part of the macros to determine when to do something in our
Makefiles based on what phase of the build we are in. For consistency,
bring this down to a single macro and use "$(PHASE_)" only.
Signed-off-by: Tom Rini <[email protected]>
|
|
Add regulator driver that allow some Qualcomm PMIC to
feed VBUS output to peripherals that are connected.
Signed-off-by: Rui Miguel Silva <[email protected]>
Acked-by: Caleb Connolly <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
Reviewed-by: Caleb Connolly <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Caleb Connolly <[email protected]>
|
|
Add a new regulator driver to control the USB VBUS supply on the Renesas
RZ/G2L and related SoCs.
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Paul Barker <[email protected]>
|
|
Use PHASE_ as the symbol to select a particular XPL build. This means
that SPL_TPL_ is no-longer set.
Update the comment in bootstage to refer to this symbol, instead of
SPL_
Signed-off-by: Simon Glass <[email protected]>
|
|
Use XPL_ as the symbol to indicate an SPL build. This means that SPL_ is
no-longer set.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add driver for TPS6287x step down convertors
Data sheet: https://www.ti.com/lit/ds/slvsgc5a/slvsgc5a.pdf
Signed-off-by: Keerthy <[email protected]>
|
|
Add Kconfig and Makefile entries for this driver now that it can build
for U-Boot.
Reviewed-by: Neil Armstrong <[email protected]>
Signed-off-by: Caleb Connolly <[email protected]>
|
|
The driver provides regulator set/get voltage enable/disable
functions for TI TPS5911 PMIC.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The driver provides regulator set/get voltage enable/disable
functions for TI TPS80031/TPS80032 PMICs.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The driver provides regulator set/get voltage
enable/disable functions for MAXIM MAX77663 PMICs.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
|
|
This driver reports the presence/absence of voltage on the PMIC's USB
VBUS pin. This information is used by the USB PHY driver. The
corresponding Linux driver uses the power supply class, which does not
exist in U-Boot. UCLASS_REGULATOR seems to be the closest match.
Signed-off-by: Samuel Holland <[email protected]>
Acked-by: Andre Przywara <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
This driver handles most voltage regulators found in X-Powers AXP PMICs.
It is based on, and intended to replace, the regulator driver in TF-A.
AXP PMIC regulators can be divided into 6 categories:
- Switches without voltage control => fully supported.
- Single linear range => fully supported.
- Two linear ranges, "step" and "2 * step" => fully supported.
- Two linear ranges, "step" and "5 * step" => only the first range is
supported. No boards are known to use the second range.
- Non-linear voltage values => fully supported.
- LDOs shared with GPIO pins => not supported.
Signed-off-by: Samuel Holland <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
Add support for setting nuvoton BMC NPCM845 voltage supply.
Signed-off-by: Jim Liu <[email protected]>
|
|
Add PCA9450 regulator driver. This is complementary driver for the BUCKn
and LDOn regulators provided by the PCA9450 PMIC driver. Currently the
driver permits reading the settngs and configuring the BUCKn and LDOn
regulators.
Reviewed-by: Fabio Estevam <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
The TPS65219 I2S PMIC features 3 Buck converters and 4 linear regulators,
2 GPOs, 1 GPIO, and 3 multi-function-pin.
This adds the driver for the Buck converters & linear regulators.
Signed-off-by: Neil Armstrong <[email protected]>
|
|
This option is used in pre-driver model code and much of it has never
been converted to driver model.
We want to add a new option to enable power support, so we can use a
simple rule in the Makefile. Rename this one, which is really about
a particular implementation of power.
Also update the pmic.h header file so it either includes the legacy
API or the driver model one.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
|
|
Anatop is an integrated regulator inside i.MX6 SoC.
There are 3 digital regulators which controls PU, CORE (ARM), and SOC.
And 3 analog regulators which controls 1P1, 2P5, 3P0 (USB).
This patch adds the Anatop regulator driver.
Signed-off-by: Ying-Chun Liu (PaulLiu) <[email protected]>
Reviewed-by: Sean Anderson <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Jaehoon Chung <[email protected]>
Cc: Peng Fan <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
|
|
Implement voltage regulators interfaced by the SCMI voltage domain
protocol. The DT bindings are defined in the Linux kernel since
SCMI voltage domain and regulators patches [1] and [2] integration
in v5.11-rc7.
Link: [1] https://github.com/torvalds/linux/commit/0f80fcec08e9c50b8d2992cf26495673765ebaba
Link: [2] https://github.com/torvalds/linux/commit/2add5cacff3531e54c50b0832128299faa9f0563
Signed-off-by: Etienne Carriere <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
|
|
Add a driver for the regulators in the the DA9063 PMIC.
Robert Beckett: move regulator modes to header so board code can set
modes. Correct mode mask used in ldo_set_mode.
Add an option CONFIG_SPL_DM_REGULATOR_DA9063.
Signed-off-by: Martin Fuzzey <[email protected]>
Signed-off-by: Robert Beckett <[email protected]>
|
|
The driver provides regulator set/get voltage
enable/disable functions for tps65941 family of PMICs.
Signed-off-by: Keerthy <[email protected]>
|
|
TPS6236x is a family of step down DC-DC converters optimized for battery
powered portable applications for a small solution size. Add a regulator
driver for supporting these devices.
Signed-off-by: Tero Kristo <[email protected]>
Signed-off-by: Keerthy <[email protected]>
|
|
BD71837 and BD71847 is PMIC intended for powering single-core,
dual-core, and quad-core SoC’s such as NXP-i.MX 8M. BD71847
is used for example on NXP imx8mm EVK.
Add regulator driver for ROHM BD71837 and BD71847 PMICs.
BD71837 contains 8 bucks and 7 LDOS. BD71847 is reduced
version containing 6 bucks and 6 LDOs. Voltages for DVS
bucks (1-4 on BD71837, 1 and 2 on BD71847) can be adjusted
when regulators are enabled. For other bucks and LDOs we may
have over- or undershooting if voltage is adjusted when
regulator is enabled. Thus this is prevented by default.
BD718x7 has a quirk which may leave power output disabled
after reset if enable/disable state was controlled by SW.
Thus the SW control is only allowed for BD71837 bucks
3 and 4 by default. The impact of this limitation must be
evaluated board-by board and restrictions may need to be
modified. (Linux driver get's these limitations from DT and we
may want to implement same on u-Boot driver).
Signed-off-by: Matti Vaittinen <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
In preparation of being able to enable/disable GPIO regulators, the
code that will be shared among the two kinds to regulators is factored
out into its own source files.
Signed-off-by: Sven Schwermer <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
|
|
Alignment with kernel driver name & binding
introduced by https://patchwork.kernel.org/cover/10761943/
to use the final marketing name = STPMIC1.
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
|
|
Prepare file modification for kernel alignment and
rename driver to stpmic1.
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
|
|
This patch allows to enable the PWM regulator driver
independent for U-Boot and SPL.
Signed-off-by: Christoph Muellner <[email protected]>
Reviewed-by: Philipp Tomsich <[email protected]>
|
|
This adds a driver for the FAN53555 family of regulators and wraps it
in a PMIC implementation.
While these devices support a 'normal' and 'suspend' mode (controlled
via an external pin) to switch between two programmable voltages, this
incarnation of the driver assumes that the device is always operating
in 'normal' mode.
Only setting/reading the programmed voltage is supported at this time
and the following device functionality remains unsupported:
- switching the selected voltage (via a GPIO)
- disabling the voltage output via software-control
This matches the functionality of the Linux driver.
Tested on a RK3399-Q7 (with 'option 5' devices): setting voltages from
the U-Boot shell and verifying output voltages on the board.
Signed-off-by: Philipp Tomsich <[email protected]>
Tested-by: Klaus Goger <[email protected]>
|
|
Complete in the drivers directory the work started with
commit 83d290c56fab ("SPDX: Convert all of our single
license tags to Linux Kernel style").
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
Add regulator driver for STM32 voltage reference buffer which can be
used as voltage reference for ADCs, DACs and external components through
dedicated VREF+ pin.
Signed-off-by: Fabrice Gasnier <[email protected]>
Signed-off-by: Patrice Chotard <[email protected]>
|
|
Enable support for the regulator functions of the STPMU1X PMIC. The
driver implements get/set api for the various BUCKS and LDOs supported
by the PMIC device. This driver is controlled by a device tree node
which includes voltage limits.
Signed-off-by: Christophe Kerello <[email protected]>
Signed-off-by: Patrick Delaunay <[email protected]>
Signed-off-by: Patrice Chotard <[email protected]>
|
|
Allow the dm driver be omitted by SPL.
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Cc: Jaehoon Chung <[email protected]>
Cc: Stefano Babic <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
|
|
exynos5422 has the s2mps11 PMIC.
s2mps11 pmic has the 10-BUCK and 38-LDO regulators.
Each IP and devices in exynos5422 can be controlled by each regulators.
This patch is support for s2mps11 regulator driver.
Signed-off-by: Jaehoon Chung <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Tested-by: Anand Moon <[email protected]>
|
|
Texas Instrument's TPS65910 PMIC contains 3 buck DC-DC converts, one
boost DC-DC converter and 8 LDOs. This patch implements driver model
support for the TPS65910 PMIC and its regulators making the get/set
API for regulator value/enable available.
This patch depends on the patch "am33xx: Add a function to query MPU
voltage in uV" to build correctly. For boards relying on the DT
include file tps65910.dtsi the v3 patch "power: extend prefix match
to regulator-name property" and an appropriate regulator naming is
also required.
Signed-off-by: Felix Brack <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
In the TI SOCs a PBIAS cell exists to provide a bias voltage to the MMC1
IO cells. Without this bias voltage these I/O cells can not function
properly. The PBIAS cell is controlled by software.
Signed-off-by: Jean-Jacques Hiblot <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This pmic includes regulators which should have their own driver. Add
a driver to support these.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
Tested-by: Marcel Ziswiler <[email protected]>
Tested-on: Beaver, Jetson-TK1
Tested-by: Stephen Warren <[email protected]>
|
|
The driver provides regulator set/get voltage
enable/disable functions for lp87565 family of PMICs.
Signed-off-by: Keerthy <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Jaehoon Chung <[email protected]>
|
|
Since this driver can be used for rk8xx series pmic,
let's rename rk808 to rk8xx, to make it clear.
Configs parts are done by sed -i "s/RK808/RK8XX/g" `grep RK808 -lr ./`
Signed-off-by: Jacob Chen <[email protected]>
|
|
The driver provides regulator set/get voltage
enable/disable functions for lp873x family of PMICs.
Signed-off-by: Keerthy <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The driver provides regulator set/get voltage
enable/disable functions for palmas family of PMICs.
Signed-off-by: Keerthy <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Add support for gpio regulators. As of now this driver caters
to gpio regulators with one gpio. Supports setting voltage values to gpio
regulators and retrieving the values.
Signed-off-by: Keerthy <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
add driver support for pwm regulator.
Signed-off-by: Elaine Zhang <[email protected]>
Signed-off-by: Kever Yang <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
For some boards the pmic interface is useful but the regulator interface
(which comes with it) is too large. Allow them to be separated such that
SPL can decide which it needs.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add regulator support for the RK808 PMIC. It integrated 4 BUCKs and 8 LDOs
all of which are supported by this driver.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add a full regulator driver for the ACT8846. This provides easy access to
voltage and current settings for each regulator.
Signed-off-by: Simon Glass <[email protected]>
|
