| Age | Commit message (Collapse) | Author |
|---|
|
In the case of SPI_XFER_BEGIN | SPI_XFER_END, the function creates a
buffer of double the size of the transaction, so that it can write the
data in into the second half. It sets the rx_offset to len, and in the
while loop we are setting an internal "din" to buffer + rx_offset.
However, at the end of each loop, the driver copies "buffer + 2 *
cmd_len" back to the data_in pointer.
This commit changes the source of the data to buffer + rx_offset.
Signed-off-by: Tomas Alvarez Vanoli <[email protected]>
|
|
Read chipselect properties from DT which are populated using 'reg'
property and save it in plat->cs[] array for later use.
Also read multi chipselect capability which is used for
parallel-memories and return errors if they are passed on using DT but
driver is not capable of handling it.
Signed-off-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Venkatesh Yadav Abbarapu <[email protected]>
|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Reviewed-by: Cédric Le Goater <[email protected]>
Reviewed-by: William Zhang <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Migrate all of COFIG_SYS_MPC* to the CFG_SYS namespace.
Signed-off-by: Tom Rini <[email protected]>
|
|
Use this new Kconfig to simplify the compilation conditions where
appropriate.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Most drivers use these access methods but a few do not. Update them.
In some cases the access is not permitted, so mark those with a FIXME tag
for the maintainer to check.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Andy Shevchenko <[email protected]>
Acked-by: Pratyush Yadav <[email protected]>
|
|
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.
The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.
Signed-off-by: Simon Glass <[email protected]>
|
|
Try to maintain some consistency between these variables by using _plat as
a suffix for them.
Signed-off-by: Simon Glass <[email protected]>
|
|
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <[email protected]>
|
|
Rename this to be consistent with the change from 'platdata'.
Signed-off-by: Simon Glass <[email protected]>
|
|
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <[email protected]>
|
|
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <[email protected]>
|
|
Modify the Freescale ESPI driver to support the driver model.
Also resolved the following problems:
===================== WARNING ======================
This board does not use CONFIG_DM_SPI. Please update
the board before v2019.04 for no dm conversion
and v2019.07 for partially dm converted drivers.
Failure to update can lead to driver/board removal
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_SPI_FLASH. Please update
the board to use CONFIG_SPI_FLASH before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Signed-off-by: Chuanhua Han <[email protected]>
Signed-off-by: Xiaowei Bao <[email protected]>
Signed-off-by: Hou Zhiqiang <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Remove spi_init definition which never used on
respective code since from many years.
Signed-off-by: Jagan Teki <[email protected]>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <[email protected]>
|
|
Replace numerical bit shift with BIT macro
in fsl_*spi.c
:%s/(1 << nr)/BIT(nr)/g
where nr = 0, 1, 2 .... 31
Cc: York Sun <[email protected]>
Cc: Haikun Wang <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
|
|
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Pavel Machek <[email protected]>
Acked-by: Lukasz Majewski <[email protected]>
Tested-by: Lukasz Majewski <[email protected]>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <[email protected]>
|
|
Replace 80 mircoseconds delay with polling flag ESPI_EV_TXE.
Signed-off-by: Hou Zhiqiang <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
85xx, 86xx PowerPC folders have code variables with CamelCase naming conventions.
because of this code checkpatch script generates "WARNING: Avoid CamelCase".
Convert variables name to normal naming convention and modify board, driver
files with updated the new structure.
Signed-off-by: Prabhakar Kushwaha <[email protected]>
Acked-by: York Sun <[email protected]>
|
|
Use DIV_ROUND_UP to simplify the code.
Signed-off-by: Axel Lin <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <[email protected]>
|
|
Rather than each driver having its own way to allocate a SPI slave,
use the new allocation function everywhere. This will make it easier
to extend the interface without breaking drivers.
Signed-off-by: Simon Glass <[email protected]>
|
|
Current espi controller driver assumes the command length of write command is
not equal to '1', it was made based on SPANSION SPI flash, but some SPI flash
driver such as SST does use write command length as '1', so write command on
SST SPI flash will not work. And the length check for write command is not
necessary for SPANSION, though it's harmless for SPANSION, it will stop write
operation on flashes like SST, so we remove the check.
Signed-off-by: Shaohui Xie <[email protected]>
Signed-off-by: Andy Fleming <[email protected]>
|
|
fsl_espi.c: In function 'spi_setup_slave':
fsl_espi.c:100: warning: format '%d' expects type 'int', but argument 3 has type
'long unsigned int'
fsl_espi.c: In function 'spi_xfer':
fsl_espi.c:237: warning: format '%08x' expects type 'unsigned int', but argument
5 has type 'const void *'
fsl_espi.c:237: warning: format '%08x' expects type 'unsigned int', but argument
7 has type 'void *'
Signed-off-by: Marek Vasut <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Mike Frysinger <[email protected]>
|
|
Signed-off-by: Mingkai Hu <[email protected]>
Singed-off-by: Jerry Huang <[email protected]>
Signed-off-by: Shaohui Xie <[email protected]>
Cc: Mike Frysinger <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
|
