| Age | Commit message (Collapse) | Author |
|---|
|
While USB DFU boot works with this patch, but the non USB boot modes like
SD Boot and flash boot fails for J784S4 EVM device.
So, Reverting this patch.
This reverts commit bfb530e06ca6c19f66c079601e568c761a001993.
Signed-off-by: Prasanth Babu Mantena <[email protected]>
|
|
The cdns3_bind() function is responsible for identifying the appropriate
driver to bind to the USB Controller's device-tree node. If the device-tree
node has the 'dr_mode' property set to 'otg', the existing approach fails
to bind a driver, leading to loss of functionality.
To address this, use the VBUS Valid field of the OTG Status register to
determine the role as follows:
- If VBUS Valid field is set, it indicates that a USB Host is supplying
power and the Controller should assume the Peripheral role.
- If VBUS Valid field is clear, it indicates the absence of a USB Host and
the Controller should assume the Host role.
Additionally, when 'dr_mode' happens to be 'otg' and the STRAP settings
are not specified, use VBUS Valid to determine the role in cdns3_drd_init()
and assign it to cdns->dr_mode.
Signed-off-by: Siddharth Vadapalli <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
The devm alloc functions that we have may follow the Linux kernel model
where allocations are (almost always) automatically free()'d. However,
quite often we don't enable, in full U-Boot, the tracking and free()'ing
functionality. This in turn leads to memory leaks because the driver
author expects that since the functions have the same name as in the
Linux Kernel they have the same behavior. In turn we then get
functionally correct commits such as commit 00e1fed93c8c ("firmware:
ti_sci: Fix memory leaks in devm_ti_sci_get_of_resource") that manually
add these calls. Rather than manually tracking allocations and
implementing free()s, rework things so that we follow expectations by
enabling the DEVRES functionality (outside of xPL phases).
This turns DEVRES from a prompted symbol to a symbol that must be
select'd, and we now remove our non-managed alloc/free functions from
outside of xPL builds.
Reviewed-by: Michael Trimarchi <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
The call to cdns3_gadget_ep_free_request will free priv_req so do the
call to list_del_init which accesses the memory pointed to by priv_req
before the free.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
Reviewed-by: Siddharth Vadapalli <[email protected]>
|
|
It is confusing to have both "$(PHASE_)" and "$(XPL_)" be used in our
Makefiles as part of the macros to determine when to do something in our
Makefiles based on what phase of the build we are in. For consistency,
bring this down to a single macro and use "$(PHASE_)" only.
Signed-off-by: Tom Rini <[email protected]>
|
|
Add Starfive cdns USB3 wrapper driver.
Signed-off-by: Minda Chen <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Tested-by: E Shattow <[email protected]>
|
|
Cdns core driver also get dr mode from wrapper devcie dts node
to make it is same with Starfive cdns USB Linux kernel driver,
Starfive 7110 OF_UPSTREAM is enabled
Signed-off-by: Minda Chen <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
USB PHY maybe need to set PHY mode in different USB
dr mode. So translate USB PHY mode to generic PHY mode
and call generic_phy_set_mode().
Signed-off-by: Minda Chen <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-dfu
u-boot-dfu-20241017
CI: https://source.denx.de/u-boot/custodians/u-boot-dfu/-/pipelines/22742
Usb Gadget:
- Fix cdns3 endpoint configuration by setting maxpacket
- Fix dwc3 cache handling when using DMA
Fastboot:
- Make AVB_VERIFY depends on FASTBOOT
|
|
Simon Glass <[email protected]> says:
When the SPL build-phase was first created it was designed to solve a
particular problem (the need to init SDRAM so that U-Boot proper could
be loaded). It has since expanded to become an important part of U-Boot,
with three phases now present: TPL, VPL and SPL
Due to this history, the term 'SPL' is used to mean both a particular
phase (the one before U-Boot proper) and all the non-proper phases.
This has become confusing.
For a similar reason CONFIG_SPL_BUILD is set to 'y' for all 'SPL'
phases, not just SPL. So code which can only be compiled for actual SPL,
for example, must use something like this:
#if defined(CONFIG_SPL_BUILD) && !defined(CONFIG_TPL_BUILD)
In Makefiles we have similar issues. SPL_ has been used as a variable
which expands to either SPL_ or nothing, to chose between options like
CONFIG_BLK and CONFIG_SPL_BLK. When TPL appeared, a new SPL_TPL variable
was created which expanded to 'SPL_', 'TPL_' or nothing. Later it was
updated to support 'VPL_' as well.
This series starts a change in terminology and usage to resolve the
above issues:
- The word 'xPL' is used instead of 'SPL' to mean a non-proper build
- A new CONFIG_XPL_BUILD define indicates that the current build is an
'xPL' build
- The existing CONFIG_SPL_BUILD is changed to mean SPL; it is not now
defined for TPL and VPL phases
- The existing SPL_ Makefile variable is renamed to SPL_
- The existing SPL_TPL Makefile variable is renamed to PHASE_
It should be noted that xpl_phase() can generally be used instead of
the above CONFIGs without a code-space or run-time penalty.
This series does not attempt to convert all of U-Boot to use this new
terminology but it makes a start. In particular, renaming spl.h and
common/spl seems like a bridge too far at this point.
The series is fully bisectable. It has also been checked to ensure there
are no code-size changes on any commit.
|
|
Use XPL_ as the symbol to indicate an SPL build. This means that SPL_ is
no-longer set.
Signed-off-by: Simon Glass <[email protected]>
|
|
Use the new symbol to refer to any 'SPL' build, including TPL and VPL
Signed-off-by: Simon Glass <[email protected]>
|
|
The function cdns3_ep_config() calculates the maximum packet size based
on the Endpoint Type and the Gadget Speed and stores it in the variable
"max_packet_size". This value is then programmed in the USB Controller
for the corresponding Endpoint. This may result in a mismatch between
the maximum packet size programmed in the USB controller and the maximum
packet size seen by the UDC Core via "maxpacket" member of "struct usb_ep".
Additionally, since TD_SIZE is calculated in cdns3_ep_run_transfer() on the
basis of the maximum packet size stored in the "maxpacket" member of
"struct usb_ep", it may lead to an incorrect value of TD_SIZE when compared
with what the USB controller actually expects (max_packet_size).
Fix this.
Fixes: 7e91f6ccdc84 ("usb: Add Cadence USB3 host and gadget driver")
Signed-off-by: Siddharth Vadapalli <[email protected]>
Reviewed-by: Roger Quadros <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mattijs Korpershoek <[email protected]>
|
|
Transfer initiation and completion for the non-zero Endpoints are
handled by cdns3_ep_run_transfer() and cdns3_transfer_completed()
respectively.
Failing to flush the cache associated with the TRB Pool within
cdns3_ep_run_transfer() results in the transfers never being initiated.
Similarly, failing to invalidate the cache associated with the TRB pool
within cdns3_transfer_completed() results in the transfers never being
completed.
Fix this.
Fixes: 7e91f6ccdc84 ("usb: Add Cadence USB3 host and gadget driver")
Signed-off-by: Siddharth Vadapalli <[email protected]>
Reviewed-by: Roger Quadros <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Implement .handle_interrupts callback as a replacement for deprecated
dm_usb_gadget_handle_interrupts() function. The new callback allows
for each DM capable USB gadget controller driver to define its own
IRQ handling implementation without colliding with other controller
drivers.
Keep the dm_usb_gadget_handle_interrupts() in this driver for non-DM
case for now, until this driver gets fully converted to DM USB gadget.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
Tested-by: Mattijs Korpershoek <[email protected]> # vim3
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mattijs Korpershoek <[email protected]>
|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
When the device port is in a low power state [U3/L2/Not Connected],
accesses to usb device registers may take a long time. This could lead to
potential core hang when the controller registers are accessed after the
port is disabled by setting DEVDS field. Setting the fast register access
bit ensures that the PHY clock is keeping up in active state.
Therefore, set fast access bit to ensure the accesses to device registers
are quick even in low power states.
commit b5148d946f45 ("usb: cdns3: gadget: set fast access bit") in the
upstream kernel is taken as reference.
Signed-off-by: Aswath Govindraju <[email protected]>
Signed-off-by: Ravi Gunasekaran <[email protected]>
Reviewed-by: Roger Quadros <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mattijs Korpershoek <[email protected]>
|
|
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Reviewed-by: Mattijs Korpershoek <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
The phys property is optional so don't complain
if it doesn't exist in device tree.
Signed-off-by: Roger Quadros <[email protected]>
|
|
Directly including asm-generic/io.h may break build because it will
cause redefenition of generic io macros if linux/io.h gets included
later, hence replace it with direct include of linux/io.h
Signed-off-by: Igor Prusov <[email protected]>
|
|
Replace instances of http://www.ti.com with https://www.ti.com
Signed-off-by: Nishanth Menon <[email protected]>
|
|
This old patch was marked as deferred. Bring it back to life, to continue
towards the removal of common.h
Move this out of the common header and include it only where needed.
Signed-off-by: Simon Glass <[email protected]>
|
|
When one of the functions does not support super speed, the composite
driver forces the gadget to high speed. But the speed is never
configured in the cdns3 gadget driver. So configure the speed
in cdns3_gadget_udc_start just like in the kernel.
Signed-off-by: Ravi Gunasekaran <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Add new compatible for AM64 SoC.
Signed-off-by: Aswath Govindraju <[email protected]>
|
|
It is a pain to have to specify the value 10 in each call. Add a new
dectoul() function and update the code to use it.
Signed-off-by: Simon Glass <[email protected]>
|
|
Rename this option so that CONFIG_IS_ENABLED can be used with it.
Signed-off-by: Simon Glass <[email protected]>
|
|
As the deadline for migration to DM_USB, when using a USB host
controller has now gone two years past the deadline, enforce migration.
This is done by:
- Ensuring that all host controller options (other than the very legacy
old MUSB ones) now select USB_HOST. USB_HOST now enforces DM_USB and
OF_CONTROL.
- Remove other parts of Kconfig logic that had platforms pick DM_USB.
- To keep Kconfig happy, have some select statements test for USB_HOST
as well.
- Re-order some Kconfig entries and menus so that we can cleanly pick
host or gadget roles. For the various HCD options that have platform
glue options, group them together and update dependencies in some
cases.
- As SPL_DM_USB is not required, on platforms that had not yet enabled
it, disable it.
Cc: Marek Vasut <[email protected]>
Cc: Icenowy Zheng <[email protected]>
Cc: Samuel Holland <[email protected]>
Cc: FUKAUMI Naoki <[email protected]>
Cc: Andre Przywara <[email protected]>
Cc: Jagan Teki <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Kernel device tree got updated to use clock name as "ref" instead of
"usb2_refclk". Fix cdns3-ti.c to use the correct name.
Fixes: 70e167495ab2 ("arm: dts: k3-j721e: Sync Linux v5.11-rc6 dts into U-Boot")
Fixes: 6239cc8c4e84 ("arm: dts: k3-j7200: Sync Linux v5.11-rc6 dts into U-Boot")
Signed-off-by: Kishon Vijay Abraham I <[email protected]>
Signed-off-by: Aswath Govindraju <[email protected]>
|
|
At present ofnode is present in the device even if it is never used. With
of-platdata this field is not used, so can be removed. In preparation for
this, change the access to go through inline functions.
Signed-off-by: Simon Glass <[email protected]>
|
|
Rename this to be consistent with the change from 'platdata'.
Signed-off-by: Simon Glass <[email protected]>
|
|
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <[email protected]>
|
|
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <[email protected]>
|
|
ep0.c also need to include dm.h so dev_xxx can access udevice fields.
Signed-off-by: Sean Anderson <[email protected]>
Tested-by: Patrick Delaunay <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <[email protected]>
|
|
Use ofnode_ instead of fdt_ APIs so that the drivers can support live DT.
This patch updates usb_get_dr_mode() and usb_get_maximum_speed() to use
ofnode as parameter instead of fdt offset. And all the drivers who use
these APIs update to use live dt APIs at the same time.
Signed-off-by: Kever Yang <[email protected]>
|
|
The implementation of dma_map_single() and dma_unmap_single() is
exactly the same for all the architectures that support them.
Factor them out to <linux/dma-mapping.h>, and make all drivers to
include <linux/dma-mapping.h> instead of <asm/dma-mapping.h>.
If we need to differentiate them for some architectures, we can
move the generic definitions to <asm-generic/dma-mapping.h>.
Add some comments to the helpers. The concept is quite similar to
the DMA-API of Linux kernel. Drivers are agnostic about what is
going on behind the scene. Just call dma_map_single() before the
DMA, and dma_unmap_single() after it.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <[email protected]>
|
|
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Anatolij Gustschin <[email protected]>
|
|
Invalidate dcache line before accessing Setup Packet contents. Otherwise
driver will see stale content on non coherent architecture.
Signed-off-by: Vignesh Raghavendra <[email protected]>
|
|
Since, commit 62f9b6544728 ("common: Move older CPU functions to their own header")
cache ops functions are declared in a separate header. Include the same
to avoid build warnings.
Signed-off-by: Vignesh Raghavendra <[email protected]>
|
|
xhci.h has now been moved to include/usb/ directory. Therefore, update the
path in the Cadence USB drivers.
Signed-off-by: Vignesh Raghavendra <[email protected]>
|
|
Add driver to handle TI specific wrapper for Cadence USB3 controller
present on J721e SoC. Based on Linux driver for the same.
Signed-off-by: Vignesh Raghavendra <[email protected]>
|
|
Implement udc_set_speed() callback to limit Controller's speed to
high-speed/full-speed when working with gadgets that are high-speed or
full-speed only
Signed-off-by: Vignesh Raghavendra <[email protected]>
|
|
Add support for USB3 host and gadget driver. This is a direct sync of
Linux kernel Cadence USB stack that from v5.4-rc1 release.
Driver has been modified so that it compiles without errors against
U-Boot code base.
Features not required for U-Boot such as scatter-gather DMA and OTG
interrupt handling has been dropped.
Signed-off-by: Jean-Jacques Hiblot <[email protected]>
[[email protected]: Add PHY support]
Signed-off-by: Vignesh Raghavendra <[email protected]>
|
