summaryrefslogtreecommitdiff
path: root/include/configs/ci20.h
AgeCommit message (Collapse)Author
2022-12-22Convert CONFIG_DM9000_BYTE_SWAPPED et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_DM9000_BYTE_SWAPPED CONFIG_DM9000_NO_SROM CONFIG_DM9000_USE_16BIT CONFIG_DM9000_DEBUG CONFIG_MXC_GPT_HCLK CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC Signed-off-by: Tom Rini <[email protected]>
2022-12-05global: Move remaining CONFIG_SYS_* to CFG_SYS_*Tom Rini
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do not easily transition to Kconfig. In many cases they likely should come from the device tree instead. Move these out of CONFIG namespace and in to CFG namespace. Signed-off-by: Tom Rini <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2022-12-05global: Move remaining CONFIG_SYS_SDRAM_* to CFG_SYS_SDRAM_*Tom Rini
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM namespace do not easily transition to Kconfig. In many cases they likely should come from the device tree instead. Move these out of CONFIG namespace and in to CFG namespace. Signed-off-by: Tom Rini <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2022-12-05global: Move remaining CONFIG_SYS_NS16550_* to CFG_SYS_NS16550_*Tom Rini
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NS16550 namespace do not easily transition to Kconfig. In many cases they likely should come from the device tree instead. Move these out of CONFIG namespace and in to CFG namespace. Signed-off-by: Tom Rini <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2022-11-10Convert CONFIG_SYS_MONITOR_LEN to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_MONITOR_LEN To do this, we set a default of 0 for everyone because there are a number of cases where we define CONFIG_SYS_MONITOR_LEN but the only impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN + CONFIG_ENV_SIZE, so we must continue to allow all boards to set this value. Update the SPL code to use 200 KB as the default raw U-Boot size directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value. Signed-off-by: Tom Rini <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2022-11-02MIPS: convert CONFIG_SYS_MIPS_TIMER_FREQ to KconfigDaniel Schwierzeck
This converts the following to Kconfig: CONFIG_SYS_MIPS_TIMER_REQ Signed-off-by: Daniel Schwierzeck <[email protected]> Reviewed-by: Stefan Roese <[email protected]>
2022-11-02MIPS: remove CONFIG_SYS_MHZDaniel Schwierzeck
Resolve all uses of CONFIG_SYS_MHZ with the currently defined value. Remove code which depends on CONFIG_SYS_MHZ but where no board configs actually use that code. Signed-off-by: Daniel Schwierzeck <[email protected]> Reviewed-by: Stefan Roese <[email protected]>
2022-07-07Convert CONFIG_SYS_BOOTM_LEN to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_BOOTM_LEN As part of this, rework error handling in boot/bootm.c so that we pass the buffer size to handle_decomp_error as CONFIG_SYS_BOOTM_LEN will not be available to host tools but we do know the size that we passed to malloc(). Cc: Soeren Moch <[email protected]> Signed-off-by: Tom Rini <[email protected]>
2022-06-06spl: Remove CONFIG_SPL_START_S_PATH and rework the logic behind itTom Rini
In some cases, when we don't use CONFIG_SPL_FRAMEWORK nor are we on PowerPC using their specific SPL/TPL framework, we need to specify the start.S file to use for these typically very constrained systems. Do this within the Makefile logic, rather than introducing a string-based CONFIG option, as this would get slightly complex to do in Kconfig for a very limited number of users. Signed-off-by: Tom Rini <[email protected]>
2022-06-06Convert CONFIG_SPL_BSS_START_ADDR to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SPL_BSS_START_ADDR Signed-off-by: Tom Rini <[email protected]>
2022-06-06Convert CONFIG_SPL_STACK to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SPL_STACK Signed-off-by: Tom Rini <[email protected]>
2022-06-06Convert CONFIG_SPL_BSS_MAX_SIZE et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SPL_BSS_MAX_SIZE CONFIG_SPL_MAX_FOOTPRINT Note that the da850evm platforms were violating the "only use one" rule here, and so now hard-code their BSS limit. Signed-off-by: Tom Rini <[email protected]>
2022-06-06Convert CONFIG_SPL_PAD_TO et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SPL_PAD_TO CONFIG_SPL_MAX_SIZE CONFIG_TPL_PAD_TO CONFIG_TPL_MAX_SIZE Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the existing places. Signed-off-by: Tom Rini <[email protected]>
2022-06-06Convert CONFIG_SYS_BOOTPARAMS_LEN to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_BOOTPARAMS_LEN Signed-off-by: Tom Rini <[email protected]>
2022-06-06Convert CONFIG_SYS_BARGSIZE to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_BARGSIZE Signed-off-by: Tom Rini <[email protected]>
2022-06-06Convert CONFIG_SYS_CBSIZE to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_CBSIZE Signed-off-by: Tom Rini <[email protected]>
2022-06-06Convert CONFIG_SYS_MAXARGS to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_MAXARGS Signed-off-by: Tom Rini <[email protected]>
2022-04-13configs: net: dm9000: Move new Kconfig option to board configsMarek Vasut
Drop legacy #define CONFIG_DRIVER_DM9000 from board include/configs/ and enable the same in Kconfig configs/ . Signed-off-by: Marek Vasut <[email protected]> Cc: Joe Hershberger <[email protected]> Cc: Ramon Fried <[email protected]> Reviewed-by: Ramon Fried <[email protected]>
2022-04-01Convert CONFIG_SYS_MONITOR_BASE to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_MONITOR_BASE Note that for how this is re-used on some PowePC platforms, we introduce CONFIG_SPL_SYS_MONITOR_BASE and CONFIG_TPL_SYS_MONITOR_BASE and use the CONFIG_VAL macro to get the correct value at build time, in the code. Signed-off-by: Tom Rini <[email protected]>
2021-12-27Convert CONFIG_CONS_INDEX et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_CONS_INDEX CONFIG_DEBUG_UART_CLOCK CONFIG_FSL_TZPC_BP147 CONFIG_GENERIC_ATMEL_MCI CONFIG_IDENT_STRING CONFIG_LIBATA CONFIG_LNX_KRNL_IMG_TEXT_OFFSET_BASE CONFIG_LPC32XX_GPIO CONFIG_MP CONFIG_MPC8XXX_GPIO CONFIG_MTD_PARTITIONS CONFIG_MVGBE CONFIG_MXC_GPIO CONFIG_NR_DRAM_BANKS CONFIG_OF_BOARD_SETUP CONFIG_OF_STDOUT_VIA_ALIAS CONFIG_OF_SYSTEM_SETUP CONFIG_PREBOOT CONFIG_ROCKCHIP_SERIAL CONFIG_RTC_ENABLE_32KHZ_OUTPUT CONFIG_RTC_MV CONFIG_SCSI_AHCI CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_SPEED CONFIG_SOFT_SPI CONFIG_SPI_FLASH_EON CONFIG_SPI_FLASH_MACRONIX CONFIG_SPI_FLASH_MTD CONFIG_SPI_FLASH_SPANSION CONFIG_SPI_FLASH_SST CONFIG_SPI_FLASH_STMICRO CONFIG_SUPPORT_RAW_INITRD CONFIG_SYS_ARCH_TIMER CONFIG_SYS_BOARD CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE CONFIG_SYS_DCACHE_OFF CONFIG_SYS_FDT_SAVE_ADDRESS CONFIG_SYS_FLASH_CFI CONFIG_SYS_FSL_ERRATUM_ESDHC135 CONFIG_SYS_HAS_SERDES CONFIG_SYS_L2CACHE_OFF CONFIG_SYS_LITTLE_ENDIAN CONFIG_SYS_LOAD_ADDR CONFIG_SYS_MMCSD_FS_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR CONFIG_SYS_NS16550 CONFIG_SYS_PLLFIN CONFIG_SYS_SPI_U_BOOT_OFFS CONFIG_TIMER_SYS_TICK_CH CONFIG_USB_EHCI_FSL CONFIG_U_QE CONFIG_VERSION_VARIABLE Signed-off-by: Tom Rini <[email protected]>
2021-11-12Convert CONFIG_SYS_CONSOLE_IS_IN_ENV to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_CONSOLE_IS_IN_ENV Signed-off-by: Tom Rini <[email protected]>
2021-11-05Convert CONFIG_SYS_HZ to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_HZ Signed-off-by: Tom Rini <[email protected]>
2021-08-31Convert CONFIG_SYS_MALLOC_LEN to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_MALLOC_LEN Signed-off-by: Tom Rini <[email protected]> Acked-by: Sean Anderson <[email protected]> Reviewed-by: Rick Chen <[email protected]>
2021-08-31Convert CONFIG_SKIP_LOWLEVEL_INIT et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SKIP_LOWLEVEL_INIT CONFIG_SKIP_LOWLEVEL_INIT_ONLY In order to do this, we need to introduce SPL and TPL variants of these options so that we can clearly disable these options only in SPL in some cases, and both instances in other cases. Signed-off-by: Tom Rini <[email protected]>
2021-08-31Convert CONFIG_SYS_LOAD_ADDR to KconfigTom Rini
Now that we have consistent usage, migrate this symbol to Kconfig. Signed-off-by: Tom Rini <[email protected]> Reviewed-by: Rick Chen <[email protected]>
2021-08-31global: Convert CONFIG_LOADADDR to CONFIG_SYS_LOADADDRTom Rini
- In most of the codebase, we reference CONFIG_SYS_LOAD_ADDR and not CONFIG_LOADADDR. - Generally, CONFIG_SYS_LOADADDR is set to CONFIG_LOADADDR and then as noted, we use CONFIG_SYS_LOADADDR. Signed-off-by: Tom Rini <[email protected]>
2020-08-08Convert CONFIG_SYS_MMC_ENV_DEV et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_MMC_ENV_DEV CONFIG_SYS_MMC_ENV_PART Note that with this conversion we now have consistent behavior with respect to ensuring that we have always selected the correct MMC device and hardware partition. Signed-off-by: Tom Rini <[email protected]>
2020-07-28Convert CONFIG_ENV_OVERWRITE to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_ENV_OVERWRITE Signed-off-by: Adam Ford <[email protected]> [trini: Rerun migration, remove some comments] Signed-off-by: Tom Rini <[email protected]>
2020-06-04Convert CONFIG_CMD_ASKENV et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_CMD_ASKENV CONFIG_CMD_BMP CONFIG_CMD_BOOTD CONFIG_CMD_CACHE CONFIG_CMD_CRC32 CONFIG_CMD_DHCP CONFIG_CMD_ENV CONFIG_CMD_EXPORTENV CONFIG_CMD_EXT2 CONFIG_CMD_EXT4 CONFIG_CMD_FLASH CONFIG_CMD_FS_GENERIC CONFIG_CMD_FUSE CONFIG_CMD_GPIO CONFIG_CMD_GPT CONFIG_CMD_GREPENV CONFIG_CMD_I2C CONFIG_CMD_IMLS CONFIG_CMD_IMPORTENV CONFIG_CMD_LOADB CONFIG_CMD_LOADS CONFIG_CMD_MEMINFO CONFIG_CMD_MII CONFIG_CMD_MTDPARTS CONFIG_CMD_NAND CONFIG_CMD_NAND_TRIMFFS CONFIG_CMD_NFS CONFIG_CMD_PCA953X CONFIG_CMD_PCA953X_INFO CONFIG_CMD_PCI CONFIG_CMD_PING CONFIG_CMD_READ CONFIG_CMD_SF CONFIG_CMD_SPI CONFIG_CMD_SPL CONFIG_CMD_SPL_WRITE_SIZE CONFIG_CMD_TIME CONFIG_CMD_TRACE CONFIG_CMD_UBI CONFIG_CMD_UBIFS CONFIG_CMD_UNZIP CONFIG_FS_EXT4 Signed-off-by: Tom Rini <[email protected]>
2020-05-08treewide: mem: Move mtest related defines to KconfigAshok Reddy Soma
Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: Ashok Reddy Soma <[email protected]> Signed-off-by: Michal Simek <[email protected]> [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: Tom Rini <[email protected]>
2019-11-20env: Finish migration of common ENV optionsTom Rini
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <[email protected]> Cc: Joe Hershberger <[email protected]> Cc: Patrick Delaunay <[email protected]> Cc: [email protected] Signed-off-by: Tom Rini <[email protected]> Acked-by: Joe Hershberger <[email protected]> Reviewed-by: Simon Goldschmidt <[email protected]>
2019-04-29configs: move CONFIG_SPL_TEXT_BASE to KconfigSimon Goldschmidt
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing values. Signed-off-by: Simon Goldschmidt <[email protected]> [trini: Re-run migration] Signed-off-by: Tom Rini <[email protected]>
2018-12-19mips: jz47xx: Add Creator CI20 platformPaul Burton
Add support for the Creator CI20 platform based on the JZ4780 SoC. Cc: Daniel Schwierzeck <[email protected]> Signed-off-by: Paul Burton <[email protected]> Signed-off-by: Marek Vasut <[email protected]> Signed-off-by: Ezequiel Garcia <[email protected]> Reviewed-by: Marek Vasut <[email protected]>
generated by cgit v1.2.3 (git 2.25.1) at 2026-04-12 11:19:33 +0000