| Age | Commit message (Collapse) | Author |
|---|
|
This board has not been converted to generic board by the deadline.
Remove it.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add option to set shell prompt string from menuconfig and migrate
boards globally.
The migration is done as follows:
- Boards that explicitly and unconditionally set CONFIG_SYS_PROMPT had the
entry moved to their defconfig files.
- Boards that defined some kind of #ifdef logic which selects the
CONFIG_SYS_PROMPT (for example qemu-mips) got an #undef CONFIG_SYS_PROMPT
right before the #ifdef logic and were left alone.
- This change forces CONFIG_SYS_PROMPT to be a per board decision, and thus
CONFIG_SYS_PROMPT was removed from all <soc>_common.h and <arch>_common.h
files. This results in a streamlined default value across platforms, and
includes the following files: spear-common, sunxi-common, mv-common,
ti_armv7_common, tegra-common, at91-sama5_common, and zynq-common.
- Boards that relied on <arch/soc>_common.h values of CONFIG_SYS_PROMPT were
not updated in their respective defconfig files under the assumption that
since they did not explicitly define a value, they're fine with whatever
the default is.
- On the other hand, boards that relied on a value defined in some
<boards>_common.h file such as woodburn_common, rpi-common,
bur_am335x_common, ls2085a_common, siemens_am33x_common, and
omap3_evm_common, had their values moved to the respective defconfig files.
- The define V_PROMPT was removed, since it is not used anywhere except for
assigning a value for CONFIG_SYS_PROMPT.
Cc: Tom Rini <[email protected]>
Cc: Masahiro Yamada <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Igor Grinberg <[email protected]>
Signed-off-by: Nikita Kiryanov <[email protected]>
[trini: Add spring, sniper, smartweb to conversion]
Signed-off-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Stefano Babic <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.
Signed-off-by: Joe Hershberger <[email protected]>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <[email protected]>
|
|
This also selects CONFIG_NET for any CONFIG_CMD_NET board.
Remove the imx default for CONFIG_NET.
This moves the config that was defined by 60296a8 (commands: add more
command entries in Kconfig).
Signed-off-by: Joe Hershberger <[email protected]>
|
|
Enable the OMAP3 specific errata code for 454179, 430973, 621766
and while at it, remove legacy non-revision checked errata logic.
Signed-off-by: Nishanth Menon <[email protected]>
Tested-by: Matt Porter <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
This is in preperation of using generic cross OMAP code.
Signed-off-by: Nishanth Menon <[email protected]>
Tested-by: Matt Porter <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP3 board select menu to omap3/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap3
Signed-off-by: Masahiro Yamada <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
PISMO_xx macros were used to define 'Platform Independent Storage MOdule'
related GPMC configurations. This patch
- Replaces these OMAP3 specific macros with generic CONFIG_xx macros as provided
by current u-boot infrastructure.
- Removes unused redundant macros, which are no longer required after
merging of common platform code in following commit
commit a0a37183bd75e74608bc78c8d0e2a34454f95a91
ARM: omap: merge GPMC initialization code for all platform
+-----------------+-----------------------------------------------------------+
| Macro | Reason for removal |
+-----------------+-----------------------------------------------------------+
| PISMO1_NOR_BASE | duplicate of CONFIG_SYS_FLASH_BASE |
+-----------------+-----------------------------------------------------------+
| PISMO1_NAND_BASE| duplicate of CONFIG_SYS_NAND_BASE |
+-----------------+-----------------------------------------------------------+
| PISMO1_ONEN_BASE| duplicate of CONFIG_SYS_ONENAND_BASE |
+-----------------+-----------------------------------------------------------+
| PISMO1_NAND_SIZE| GPMC accesses NAND device via I/O mapped registers so |
| | configuring GPMC chip-select for smallest allowable |
| | segment (GPMC_SIZE_16M) is enough. |
+-----------------+-----------------------------------------------------------+
| PISMO1_ONEN_SIZE| OneNAND uses a fixed GPMC chip-select address-space of |
| | 128MB (GPMC_SIZE_128M) |
+-----------------+-----------------------------------------------------------+
+-----------------+-----------------------------------------------------------+
| PISMO1_NOR | Unused Macros |
| PISMO1_NAND | |
| PISMO2_CS0 | |
| PISMO2_CS1 | |
| PISMO1_ONENAND | |
| PISMO2_NAND_CS0 | |
| PISMO2_NAND_CS1 | |
| PISMO1_NOR_BASE | |
| PISMO1_NAND_BASE| |
| PISMO2_CS0_BASE | |
+-----------------+-----------------------------------------------------------+
Signed-off-by: Pekon Gupta <[email protected]>
|
|
bus-width
GPMC controller needs to be configured based on bus-width of the NAND device
connected to it. Also, dynamic detection of NAND bus-width from on-chip ONFI
parameters is not possible in following situations:
SPL: SPL NAND drivers does not support ONFI parameter reading.
U-boot: GPMC controller iniitalization is done in omap_gpmc.c:board_nand_init()
which is called before probing for devices, hence any ONFI parameter
information is not available during GPMC initialization.
Thus, OMAP NAND driver expected board developers to explicitely write GPMC
configurations specific to NAND device attached on board in board files itself.
But this was troublesome for board manufacturers as they need to dive into
lengthy platform & SoC documents to find details of GPMC registers and
appropriate configurations to get NAND device working.
This patch instead adds existing CONFIG_SYS_NAND_BUSWIDTH_16BIT to board config
hich indicates that connected NAND device has x16 bus-width. And then based on
this config GPMC driver itself initializes itself based on NAND bus-width. This
keeps board developers free from knowing GPMC controller specific internals.
Signed-off-by: Pekon Gupta <[email protected]>
|
|
OMAP NAND driver can detect Page-size and OOB-size of NAND device from ONFI
params or nand_id[] table. And based on that it defines ECC layout.
This patch
1) removes following board configs used for defining NAND ECC layout
- GPMC_NAND_ECC_LP_x16_LAYOUT (for large page x16 NAND)
- GPMC_NAND_ECC_LP_x8_LAYOUT (for large page x8 NAND)
- GPMC_NAND_ECC_SP_x16_LAYOUT (for small page x16 NAND)
- GPMC_NAND_ECC_SP_x8_LAYOUT (for small page x8 NAND)
2) removes unused #defines in common omap_gpmc.h depending on above configs
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5
Signed-off-by: Pekon Gupta <[email protected]>
|
|
- add omap24xx driver to new multibus/multiadpater support
- adapted all config files, which uses this driver
Tested on the am335x based siemens boards rut, dxr2 and pxm2
posted here:
http://patchwork.ozlabs.org/patch/263211/
Signed-off-by: Heiko Schocher <[email protected]>
Tested-by: Tom Rini <[email protected]>
Cc: Lars Poeschel <[email protected]>
Cc: Steve Sakoman <[email protected]>
Cc: Thomas Weber <[email protected]>
Cc: Tom Rix <[email protected]>
Cc: Grazvydas Ignotas <[email protected]>
Cc: Enric Balletbo i Serra <[email protected]>
Cc: Luca Ceresoli <[email protected]>
Cc: Igor Grinberg <[email protected]>
Cc: Ilya Yanok <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Nishanth Menon <[email protected]>
Cc: Pali Rohár <[email protected]>
Cc: Peter Barada <[email protected]>
Cc: Nagendra T S <[email protected]>
Cc: Michael Jones <[email protected]>
Cc: Raphael Assenat <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
Acked-by: Stefano Babic <[email protected]>
|
|
Remove platform CONFIG_SYS_HZ definition for configs a-z*.
Signed-off-by: Rob Herring <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Adding a new CONFIG_OMAP_COMMON which is included by all boards
that needs to build cpu/armv7/omap-common folder.
Signed-off-by: Lokesh Vutla <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <[email protected]>
|
|
"CONFIG_SYS_I2C_BUS" and "CONFIG_SYS_I2C_BUS_SELECT" don't appear anywhere
outside of config files.
Signed-off-by: Michael Jones <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
|
|
Remove the unused PHYS_SDRAM_1_SIZE from OMAP3 config files.
Signed-off-by: Thomas Weber <[email protected]>
|
|
CONFIG_STACKSIZE is not referenced anywhere except on AVR32, but present
in most ARM board config files.
IRQs are only enabled for 1 config, so remove the unused config options
for IRQ and FIQ stack size as well.
Cc: Albert ARIBAUD <[email protected]>
Signed-off-by: Rob Herring <[email protected]>
|
|
Signed-off-by: Marek Vasut <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: U-Boot DM <[email protected]>
Cc: Tom Rini <[email protected]>
Acked-by: Tom Rini <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2. I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.
Cc: Stefano Babic <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Acked-by: Stefano Babic <[email protected]>
|
|
This patch removes the unused definitions:
CONFIG_OMAP3_MICRON_DDR
CONFIG_OMAP3_NUMONYX_DDR
CONFIG_OMAP3_INFINEON_DDR
Signed-off-by: Thomas Weber <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
Acked-by: Luca Ceresoli <[email protected]>
|
|
This patch removes the unused definition of SDRC_R_C_B
from the config files.
Acked-by: Enric Balletbo i Serra <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
Signed-off-by: Thomas Weber <[email protected]>
Acked-by: Luca Ceresoli <[email protected]>
Acked-by: Tom Rini <[email protected]>
|
|
This patch removes the CONFIG_OMAP3430, because it is unused.
Acked-by: Enric Balletbo i Serra <[email protected]>
Acked-by: Tom Rini <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
Signed-off-by: Thomas Weber <[email protected]>
Acked-by: Luca Ceresoli <[email protected]>
|
|
MACH_TYPE_OMAP3_CPS was dropped in the latest mach-types sync (47af6f61bcd9)
because it is not mainlined in Linux.
Signed-off-by: Luca Ceresoli <[email protected]>
Cc: Sandeep Paulraj <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: Wolfgang Denk <[email protected]>
CC: Tom Rini <[email protected]>
Signed-off-by: Sandeep Paulraj <[email protected]>
|
|
Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it. So scrub all references to it.
Signed-off-by: Mike Frysinger <[email protected]>
|
|
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver. This patch is based on the work done for Beagle, etc.
Signed-off-by: Tom Rini <[email protected]>
Signed-off-by: Sandeep Paulraj <[email protected]>
|
|
Signed-off-by: Christopher Harvey <[email protected]>
|
|
Board support for the DIG297 board manufactured by Comelit Group SpA.
It is a custom board based on the BeagleBoard <http://beagleboard.org/> by
Texas Instruments.
The board support is based on the BeagleBoard implementation.
Signed-off-by: Luca Ceresoli <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: Sandeep Paulraj <[email protected]>
Signed-off-by: Sandeep Paulraj <[email protected]>
|
