| Age | Commit message (Collapse) | Author |
|---|
|
Switch PHY_ANEG_TIMEOUT to CONFIG_PHY_ANEG_TIMEOUT Kconfig symbol.
This removes one more configuration headers option finalizes its
Kconfig symbol conversion. No functional change expected.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Move to using .env file for setting up environment variables for K2x_evm.
Signed-off-by: Andrew Davis <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
This is more complex than it needs to be and makes converting these
boards over to plain text env files more difficult. Remove setting
mtdparts as the DTS already contain the partitions. While here also
drop the conflicting definitions from the K2 defconfigs.
Signed-off-by: Andrew Davis <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Perform a simple rename of CONFIG_KSNET_CPSW_NUM_PORTS to CFG_KSNET_CPSW_NUM_PORTS
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_KSNET_NETCP_V1_0
CONFIG_KSNET_NETCP_V1_5
Signed-off-by: Tom Rini <[email protected]>
|
|
This removes the following unreferenced CONFIG symbols:
CONFIG_FDTADDR
CONFIG_FDTFILE
CONFIG_FLASH_SECTOR_SIZE
CONFIG_FSL_CPLD
CONFIG_HDMI_ENCODER_I2C_ADDR
CONFIG_I2C_MVTWSI
CONFIG_I2C_RTC_ADDR
CONFIG_IRAM_END
CONFIG_IRAM_SIZE
CONFIG_KSNET_MDIO_PHY_CONFIG_ENABLE
CONFIG_L1_INIT_RAM
CONFIG_MACB_SEARCH_PHY
CONFIG_MIU_2BIT_21_7_INTERLEAVED
CONFIG_MTD_NAND_VERIFY_WRITE
CONFIG_MVGBE_PORTS
CONFIG_NETDEV
CONFIG_NUM_DSP_CPUS
CONFIG_PHY_BASE_ADR
CONFIG_PHY_INTERFACE_MODE
CONFIG_PSRAM_SCFG
CONFIG_RAMBOOT_SPIFLASH
CONFIG_RAMBOOT_TEXT_BASE
CONFIG_RD_LVL
CONFIG_ROCKCHIP_SDHCI_MAX_FREQ
CONFIG_SETUP_INITRD_TAG
CONFIG_SH_QSPI_BASE
CONFIG_SMDK5420
CONFIG_SOCRATES
CONFIG_SPI_ADDR
CONFIG_SPI_FLASH_QUAD
CONFIG_SPI_FLASH_SIZE
CONFIG_SPI_HALF_DUPLEX
CONFIG_SPI_N25Q256A_RESET
CONFIG_TEGRA_SLINK_CTRLS
CONFIG_TPM_TIS_BASE_ADDRESS
CONFIG_UBOOT_SECTOR_COUNT
CONFIG_UBOOT_SECTOR_START
CONFIG_VAR_SIZE_SPL
CONFIG_VERY_BIG_RAM
And also:
BL1_SIZE
PHY_NO
RESERVE_BLOCK_SIZE
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_SYS_NAND_PAGE_2K
CONFIG_SYS_NAND_PAGE_4K
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This is a little tricky since SoCFPGA has code to determine this as
runtime. Introduce a guard variable for platforms to select if they
have a static value to use. Then for ARCH_SOCFPGA, call
cm_get_qspi_controller_clk_hz() and otherwise continue the previous
behavior.
Cc: Jagan Teki <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_USE_BOOTCOMMAND
CONFIG_BOOTCOMMAND
CONFIG_RAMBOOTCOMMAND
CONFIG_NFSBOOTCOMMAND
Signed-off-by: Tom Rini <[email protected]>
|
|
Move the individual keystone 2 SoC symbols to the mach Kconfig file,
select them as needed.
Signed-off-by: Tom Rini <[email protected]>
|
|
Rename CONFIG_ENV_KS2_BOARD_SETTINGS to ENV_KS2_BOARD_SETTINGS so that
it better fits with the rest of the environment addition macros.
Cc: Vitaly Andrianov <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Add board detection support for K2G ICE with FlagChip 1GHz silicon.
Signed-off-by: Lokesh Vutla <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_CADENCE_QSPI
Signed-off-by: Tom Rini <[email protected]>
|
|
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <[email protected]>
Cc: Joe Hershberger <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Cc: [email protected]
Signed-off-by: Tom Rini <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
Reviewed-by: Simon Goldschmidt <[email protected]>
|
|
This is the first part of a larger effort I would like to propose to
unify and simplify the default set of environment variables.
When many early environment variables were named there were fewer images
being loaded, usually just a kernel. At this time names like 'loadaddr'
would suffice. Now we have more images and many more commands that act on
them, often re-using the same variable for several different uses. The
contents of a variable are also not immediately known causing one to have
to look up a chain of variables to understand what a command is actually
doing. I suggest the following.
To start, all variables containing names should be prefixed with name_
and addresses with addr_. This is like how K2 already does things and
allows for simple universal commands like:
get_fdt_nfs=nfs ${addr_fdt} /boot/${name_fdt}
Which is very clear on what is intended here and would work across all
board that using the this naming convention.
We can do this one variable at a time, start here with addr_fit.
Signed-off-by: Andrew F. Davis <[email protected]>
Acked-by: Andreas Dannenberg <[email protected]>
|
|
The ISW_ENTRY_ADDR Kconfig option under mach-omap2 isn't a SoC specific
notion but rather "where is our previous stage loaded in memory?"
option. Make use of this on ARCH_KEYSTONE rather than SPL_TEXT_BASE for
our HS builds that are not using SPL anyhow.
Cc: Vitaly Andrianov <[email protected]>
Cc: Andrew F. Davis <[email protected]>
Cc: Lokesh Vutla <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Lokesh Vutla <[email protected]?
|
|
This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEED
I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <[email protected]>
|
|
Convert CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig
Signed-off-by: Alex Kiernan <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
Reviewed-by: Petr Vorel <[email protected]>
Reviewed-by: Petr Vorel <petr.vorel at gmail.com>
|
|
|
|
possible"
This reverts commit 57897c13de03ac0136d64641a3eab526c6810387.
Using bounce_buf.c to handle non-DMA alignment problems is bad as
bounce_buf.c does cache manipulations which is not required. Therefore
revert this patch in favour of local bounce buffer solution in the next
patch.
Signed-off-by: Vignesh R <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Acked-by: Simon Goldschmidt <[email protected]>
Reviewed-by: Jason Rush <[email protected]>
Acked-by: Jason Rush <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Cleanup unused #define values that are read from the DT.
Tested on TI K2G platform:
Tested-by: Vignesh R <[email protected]>
Tested on a socfpga-cyclonev board:
Tested-by: Simon Goldschmidt <[email protected]>
Signed-off-by: Jason Rush <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
Acked-by: Simon Goldschmidt <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
Added support for K2G EVM with FlipChip SoC of which
ARM/DDR3 runs at 1GHz/1066 MT/s. The patch is also
backward compatible with old revision EVM and EVM
with WireBond SoC. Their ARM/DDR3 run at 600MHz/800 MT/s.
The new SoC supports 2 different speeds at 1GHz and 600MHz.
Modyfied the CPU Name to show which SoC is used in the EVM.
Modified the DDR3 configuration to reflect New SoC supports
2 different CPU and DDR3 speeds, 1GHz/1066MT and 600MHz/800MT.
Added new inline function board_it_k2g_g1() for the new FlipChip 1GHz,
and set the u-boot env variable board_name accordingly.
Modified findfdt script in u-boot environment variable to include new k2g board type.
Signed-off-by: Rex Chang <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
|
|
Now that we have multi dtb enabled in u-boot allocate
128K space for u-boot.
Signed-off-by: Lokesh Vutla <[email protected]>
|
|
On all other platforms the command 'findfdt' populates the variable
'fdtfile', but on K2G we only populate 'name_fdt'. The generic boot
and automation scripts fail when 'findfdt' is not populated, fix
this for K2G.
Signed-off-by: Andrew F. Davis <[email protected]>
|
|
The PMMC firmware should be bundled with the FIT image for HS devices,
remove the steps that load and install this firmware outside of FIT.
Signed-off-by: Andrew F. Davis <[email protected]>
|
|
Signed-off-by: Alexandru Gagniuc <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
We rename the various FAT_ENV_xxx options to CONFIG_ENV_FAT_xxx so that
they can be modified via Kconfig. Migrate all existing users to the new
values.
Signed-off-by: Tom Rini <[email protected]>
|
|
We first split the CONFIG_BOOTCOMMAND into its components to improve
readability. We then make the following order changes:
- Run findfdt first so the fdt name can be used in envboot like OMAP
- Install the boot monitor before running the PMMC so we can make any
needed secure changes before PMMC, do this on both HS and non-HS
- Move set_name_pmmc to just before get_pmmc_${boot}
Signed-off-by: Andrew F. Davis <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Updates the default u-boot environment variables to support secure
boot. On secure devices, a secure boot monitor (sec-bm) needs to
be installed by u-boot.
Signed-off-by: Madan Srinivas <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Updates the default u-boot environment variables to support FIT image
loading.
Signed-off-by: Andrew F. Davis <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_FAT
Signed-off-by: Simon Glass <[email protected]>
|
|
Enable CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to allow "board_name" to
be set depending on the board it is being ran on.
Update findfdt to use this new dynamic board_name value to determine
which dtb should be used.
Signed-off-by: Franklin S Cooper Jr <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Since config fallbacks contained in include/config_fallbacks.h
come into k2g_evm.h file through ti_armv7_keystone2.h, it should
be the last file included.
Without this, #define of FAT_WRITE when environment is in FAT
does not happen as the environment location is decided later
in the file.
Similar issues can come with other config fallbacks implemented.
Signed-off-by: Sekhar Nori <[email protected]>
|
|
Not all TI Keystone2 EVMs want environment in NAND flash.
K2G EVM which has an MMC/SD slot, keep environment in a
FAT partition on SD card.
Since ti_armv7_keystone2.h defines environment is in NAND,
boards which do not follow that have to #undef'ine that
configuration. This leads to ugly ordering issues around
where exactly the include of ti_armv7_keystone2.h can come
in within the k2*_evm.h files.
Move environment location to config file of each board.
This should make it easy to change it for any one board
without affecting all other boards.
Signed-off-by: Sekhar Nori <[email protected]>
|
|
Introduce include/environment/ti/mmc.h that
consolidates environment variable definitions
for various TI boards that support MMC/SD.
This allows reuse of same environment variables
on non-ARMv7 TI platforms like OMAP-L138 for
example.
While at it, move DFU-related environment variable
includes to only non-SPL builds for AM335x and
AM437x since they are not really used for SPL
today.
Signed-off-by: Sekhar Nori <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
SPI U-Boot image for K2 boards have now exceeded 512K partition
allocated to it and no longer fit the partitions defined in kernel DTS
file. Therefore, pass an updated MTD partition table from U-Boot as
kernel command line arguments to avoid kernel from accidentally
modifying boot loader image that has overflowed to next user partition.
To do is, introduce a common environment file for declaring SPI
partition so that each individual boards need not repeat the same.
Choose appropriate SPI bus from board config file and pass it as command
line argument to kernel.
Signed-off-by: Vignesh R <[email protected]>
|
|
Now, CONFIG_GENERIC_MMC seems equivalent to CONFIG_MMC.
Let's create an entry for "config GENERIC_MMC" with "default MMC",
then convert all macro defines in headers to Kconfig. Almost all
of the defines will go away.
I see only two exceptions:
configs/blanche_defconfig
configs/sandbox_noblk_defconfig
They define CONFIG_GENERIC_MMC, but not CONFIG_MMC. Something
might be wrong with these two boards, so should be checked later.
Anyway, this is the output of the moveconfig tool.
This commit was created as follows:
[1] create a config entry in drivers/mmc/Kconfig
[2] tools/moveconfig.py -r HEAD GENERIC_MMC
[3] manual clean-up of garbage comments in doc/README.* and
include/configs/*.h
Signed-off-by: Masahiro Yamada <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Move (and rename) the following CONFIG options to Kconfig:
CONFIG_DAVINCI_MMC (renamed to CONFIG_MMC_DAVINCI)
CONFIG_OMAP_HSMMC (renamed to CONFIG_MMC_OMAP_HS)
CONFIG_MXC_MMC (renamed to CONFIG_MMC_MXC)
CONFIG_MXS_MMC (renamed to CONFIG_MMC_MXS)
CONFIG_TEGRA_MMC (renamed to CONFIG_MMC_SDHCI_TEGRA)
CONFIG_SUNXI_MMC (renamed to CONFIG_MMC_SUNXI)
They are the same option names as used in Linux.
This commit was created as follows:
[1] Rename the options with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_DAVINCI_MMC/CONFIG_MMC_DAVINCI/g
s/CONFIG_OMAP_HSMMC/CONFIG_MMC_OMAP_HS/g
s/CONFIG_MXC_MMC/CONFIG_MMC_MXC/g
s/CONFIG_MXS_MMC/CONFIG_MMC_MXS/g
s/CONFIG_TEGRA_MMC/CONFIG_MMC_SDHCI_TEGRA/g
s/CONFIG_SUNXI_MMC/CONFIG_MMC_SUNXI/g
'
[2] Commit the changes
[3] Create entries in driver/mmc/Kconfig.
(copied from Linux)
[4] Move the options with the following command
tools/moveconfig.py -y -r HEAD \
MMC_DAVINCI MMC_OMAP_HS MMC_MXC MMC_MXS MMC_SDHCI_TEGRA MMC_SUNXI
[5] Sort and align drivers/mmc/Makefile for readability
Signed-off-by: Masahiro Yamada <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
According to Section 11.15.4.9.2 Indirect Write Controller of K2G SoC
TRM SPRUHY8D[1], the external master is only permitted to issue 32-bit
data interface writes until the last word of an indirect transfer
otherwise indirect writes is known to fails sometimes. So, make sure
that QSPI indirect writes are 32 bit sized except for the last write. If
the txbuf is unaligned then use bounce buffer to avoid data aborts.
So, now that the driver uses bounce_buffer, enable CONFIG_BOUNCE_BUFFER
for all boards that use Cadence QSPI driver.
[1]www.ti.com/lit/ug/spruhy8d/spruhy8d.pdf
Signed-off-by: Vignesh R <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Commit 7a777f6d6f35 ("mmc: Add generic Kconfig option") created
a Kconfig entry for this option without any actual moves, then
commit 44c798799f66 ("sunxi: Use Kconfig CONFIG_MMC") moved
instances only for SUNXI.
We generally do not like such partial moves. This kind of work
is automated by tools/moveconfig.py, so it is pretty easy to
complete this move.
I am adding "default ARM || PPC || SANDBOX" (suggested by Tom).
This shortens the configs and will ease new board porting.
This commit was created as follows:
[1] Edit Kconfig (remove the "depends on", add the "default",
copy the prompt and help message from Linux)
[2] Run 'tools/moveconfig.py -y -s -r HEAD MMC'
Signed-off-by: Masahiro Yamada <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
|
|
The config option TARGET_K2x_EVM is set by the k2x defconfigs to pick
a board target, but the header configs also set K2x_EVM. This config
is redundant, remove it and use TARGET_K2x_EVM everywhere in its place.
Signed-off-by: Andrew F. Davis <[email protected]>
Reviewed-by: Lokesh Vutla <[email protected]>
|
|
As boot monitor contains a mkimage header, it can be loaded at any location.
So, have a common addr_mon address across all keystone2 SoCs. And also
making sure that boot monitor is installed early during default boot to
avoid any overlapping with other images.
Signed-off-by: Lokesh Vutla <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
On K2G, the PCIe SerDes h/w is a re-use from other K2 devices and SerDes
driver requires a firmware image to initialize the SerDes h/w device.
This is firmware is part of the initramfs file that is loaded to memory
in u-boot and passed to kernel as in other K2 platforms. This patch
customize the u-boot env to have this done automatically when the K2G EVM
boots up. With this, a user may be able to boot the EVM with a standard
PCIe card at the x1 PCIe slot and release image and test PCIe devices
such as NIC, SATA etc.
Signed-off-by: Murali Karicheri <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Enable Cadence QSPI controller support to use QSPI on K2G SoC. Also
enable Spansion flash support to access s25fl512s flash present on K2G
QSPI bus.
Signed-off-by: Vignesh R <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Now that all Keystone2 dts file names are changed in Linux kernel, reflect the
same in evn variables inorder to find the right dtb file.
Signed-off-by: Lokesh Vutla <[email protected]>
|
|
Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig
Signed-off-by: Tom Rini <[email protected]>
|
|
After power cycle of a K2G EVM dhcp fails due to a auto-negotiation
timeout. This commit increases the timeout to fix the issue.
Signed-off-by: Vitaly Andrianov <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
For k2l, k2e and k2hk, ubi is set to default boot in uboot
environment settings; while for k2g, mmc should be the
default boot. This patch is to set mmc as default for k2g-evm
Signed-off-by: Yan Liu <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
This patch updates the env script to include a initramfs with firmware
loaded and provided to kernel through second argument of bootz command
during boot. Defined DEFAULT_FW_INITRAMFS_BOOT_ENV to have all of the
required env variables and use it in evm specific config file.
The K2 linux drivers for PCIe and NetCP (1G, 10G) requires serdes
firmwares. These requires firmware to be available early through the boot
process in some cases to satisfy firmware requests from driver. Hence use
a small initramfs to provide the same and update boot env to accommodate
this in the boot flow. This method is used when rootfs is nfs and ubifs.
This fs contains just lib/firmware folder with all required firmware.
When rootfs is on initramfs, then the filesystem has the firmware under
lib/firmware and this early initramfs is not required and is not used.
Signed-off-by: Murali Karicheri <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
