summaryrefslogtreecommitdiff
path: root/include/configs/ls1046a_common.h
AgeCommit message (Collapse)Author
4 daysls1046a: add env variables to assist bootChunguang Li
Add LS1046ARDB-specific variables to assist the boot flow, and update the related common and other LS1046A board settings accordingly. Signed-off-by: Chunguang Li <[email protected]> Signed-off-by: Peng Fan <[email protected]>
2024-10-11include: Use CONFIG_XPL_BUILD instead of CONFIG_SPL_BUILDSimon Glass
Use the new symbol to refer to any 'SPL' build, including TPL and VPL Signed-off-by: Simon Glass <[email protected]>
2023-10-10fsl-layerscape: drop obsolete PPA secure firmware supportLaurentiu Tudor
PPA was a secure firmware developed in-house which is no longer supported and replaced by TF-A quite some years ago. Drop support for it. Signed-off-by: Laurentiu Tudor <[email protected]> Signed-off-by: Peng Fan <[email protected]>
2022-12-23global: Migrate CONFIG_EXTRA_ENV_SETTINGS to CFGTom Rini
Perform a simple rename of CONFIG_EXTRA_ENV_SETTINGS to CFG_EXTRA_ENV_SETTINGS Signed-off-by: Tom Rini <[email protected]>
2022-12-22nxp: Rename CONFIG_U_BOOT_HDR_SIZE to FSL_U_BOOT_HDR_SIZETom Rini
This is always defined to 16K, so we move this over to include/fsl_validate.h to start with. Next, we rename this from CONFIG_ to FSL_. Coalesce the various comments around this definition to be in fsl_validate.h as well to explain the usage. Signed-off-by: Tom Rini <[email protected]>
2022-12-22global: Remove unused CONFIG symbolsTom Rini
This removes the following unreferenced CONFIG symbols: CONFIG_FDTADDR CONFIG_FDTFILE CONFIG_FLASH_SECTOR_SIZE CONFIG_FSL_CPLD CONFIG_HDMI_ENCODER_I2C_ADDR CONFIG_I2C_MVTWSI CONFIG_I2C_RTC_ADDR CONFIG_IRAM_END CONFIG_IRAM_SIZE CONFIG_KSNET_MDIO_PHY_CONFIG_ENABLE CONFIG_L1_INIT_RAM CONFIG_MACB_SEARCH_PHY CONFIG_MIU_2BIT_21_7_INTERLEAVED CONFIG_MTD_NAND_VERIFY_WRITE CONFIG_MVGBE_PORTS CONFIG_NETDEV CONFIG_NUM_DSP_CPUS CONFIG_PHY_BASE_ADR CONFIG_PHY_INTERFACE_MODE CONFIG_PSRAM_SCFG CONFIG_RAMBOOT_SPIFLASH CONFIG_RAMBOOT_TEXT_BASE CONFIG_RD_LVL CONFIG_ROCKCHIP_SDHCI_MAX_FREQ CONFIG_SETUP_INITRD_TAG CONFIG_SH_QSPI_BASE CONFIG_SMDK5420 CONFIG_SOCRATES CONFIG_SPI_ADDR CONFIG_SPI_FLASH_QUAD CONFIG_SPI_FLASH_SIZE CONFIG_SPI_HALF_DUPLEX CONFIG_SPI_N25Q256A_RESET CONFIG_TEGRA_SLINK_CTRLS CONFIG_TPM_TIS_BASE_ADDRESS CONFIG_UBOOT_SECTOR_COUNT CONFIG_UBOOT_SECTOR_START CONFIG_VAR_SIZE_SPL CONFIG_VERY_BIG_RAM And also: BL1_SIZE PHY_NO RESERVE_BLOCK_SIZE Signed-off-by: Tom Rini <[email protected]>
2022-12-05Convert CONFIG_HWCONFIG to KconfigTom Rini
This converts the following to Kconfig: CONFIG_HWCONFIG Signed-off-by: Tom Rini <[email protected]>
2022-12-05global: Move remaining CONFIG_SYS_* to CFG_SYS_*Tom Rini
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do not easily transition to Kconfig. In many cases they likely should come from the device tree instead. Move these out of CONFIG namespace and in to CFG namespace. Signed-off-by: Tom Rini <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2022-12-05global: Move remaining CONFIG_SYS_SDRAM_* to CFG_SYS_SDRAM_*Tom Rini
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM namespace do not easily transition to Kconfig. In many cases they likely should come from the device tree instead. Move these out of CONFIG namespace and in to CFG namespace. Signed-off-by: Tom Rini <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2022-12-05Convert CONFIG_SYS_PMAN et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_NOBQFMAN CONFIG_SYS_DPAA_DCE CONFIG_SYS_DPAA_FMAN CONFIG_SYS_DPAA_PME CONFIG_SYS_DPAA_RMAN CONFIG_SYS_PMAN Signed-off-by: Tom Rini <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2022-12-05Remove unused symbolsTom Rini
This commit removes the following unused symbols: CONFIG_SYS_NVRAM_BASE_ADDR CONFIG_SYS_NVRAM_SIZE CONFIG_SYS_PAXE_BASE CONFIG_SYS_PCCNT CONFIG_SYS_PCDAT CONFIG_SYS_PCDDR CONFIG_SYS_PCI1_ADDR CONFIG_SYS_PCI2_ADDR CONFIG_SYS_PCI1_IO_BUS CONFIG_SYS_PCI1_IO_SIZE CONFIG_SYS_PCI1_MEM_BUS CONFIG_SYS_PCI1_MEM_SIZE CONFIG_SYS_PCIE3_ADDR CONFIG_SYS_PCIE4_ADDR CONFIG_SYS_PCIE3_IO_PHYS CONFIG_SYS_PCIE3_IO_VIRT CONFIG_SYS_PCIE4_IO_PHYS CONFIG_SYS_PCIE4_IO_VIRT CONFIG_SYS_PLL_SETTLING_TIME CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_SP_CENA_SIZE CONFIG_SYS_RCAR_I2C0_BASE CONFIG_SYS_RCAR_I2C1_BASE CONFIG_SYS_RCAR_I2C2_BASE CONFIG_SYS_RCAR_I2C3_BASE CONFIG_SYS_SATA CONFIG_SYS_SDRAM_BASE2 CONFIG_SYS_SGMII_REFCLK_MHZ CONFIG_SYS_SGMII_LINERATE_MHZ CONFIG_SYS_SGMII_RATESCALE CONFIG_SYS_SH_SDHI0_BASE CONFIG_SYS_SH_SDHI0_BASE CONFIG_SYS_SH_SDHI1_BASE CONFIG_SYS_SH_SDHI2_BASE CONFIG_SYS_SH_SDHI3_BASE CONFIG_SYS_SPI_ST_ENABLE_WP_PIN CONFIG_SYS_SPI_U_BOOT_SIZE CONFIG_SYS_VCXK_ACKNOWLEDGE_DDR CONFIG_SYS_VCXK_ACKNOWLEDGE_PIN CONFIG_SYS_VCXK_ACKNOWLEDGE_PORT CONFIG_SYS_VCXK_BASE CONFIG_SYS_VCXK_DEFAULT_LINEALIGN CONFIG_SYS_VCXK_DOUBLEBUFFERED CONFIG_SYS_VCXK_ENABLE_DDR CONFIG_SYS_VCXK_ENABLE_PIN CONFIG_SYS_VCXK_ENABLE_PORT CONFIG_SYS_VCXK_INVERT_DDR CONFIG_SYS_VCXK_INVERT_PIN CONFIG_SYS_VCXK_INVERT_PORT CONFIG_SYS_VCXK_REQUEST_DDR CONFIG_SYS_VCXK_REQUEST_PIN CONFIG_SYS_VCXK_REQUEST_PORT CONFIG_SYS_VSC7385_BR_PRELIM CONFIG_SYS_VSC7385_OR_PRELIM Signed-off-by: Tom Rini <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2022-12-05global: Move remaining CONFIG_SYS_NS16550_* to CFG_SYS_NS16550_*Tom Rini
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NS16550 namespace do not easily transition to Kconfig. In many cases they likely should come from the device tree instead. Move these out of CONFIG namespace and in to CFG namespace. Signed-off-by: Tom Rini <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2022-12-05Convert CONFIG_SYS_NS16550_MEM32 et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SPL_NS16550_MIN_FUNCTIONS CONFIG_SYS_NS16550_MEM32 CONFIG_SYS_NS16550_PORT_MAPPED CONFIG_SYS_NS16550_REG_SIZE CONFIG_SYS_NS16550_SERIAL To do this we also introduce CONFIG_SPL_SYS_NS16550_SERIAL so that platforms can enable the legacy driver here for SPL. Signed-off-by: Tom Rini <[email protected]>
2022-12-05global: Move remaining CONFIG_SYS_NAND_* to CFG_SYS_NAND_*Tom Rini
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NAND namespace do not easily transition to Kconfig. In many cases they likely should come from the device tree instead. Move these out of CONFIG namespace and in to CFG namespace. Signed-off-by: Tom Rini <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2022-11-10global: Migrate CONFIG_SYS_FSL* symbols to the CFG_SYS namespaceTom Rini
Migrate all of COFIG_SYS_FSL* to the CFG_SYS namespace. Signed-off-by: Tom Rini <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2022-11-10Convert CONFIG_SYS_MONITOR_LEN to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_MONITOR_LEN To do this, we set a default of 0 for everyone because there are a number of cases where we define CONFIG_SYS_MONITOR_LEN but the only impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN + CONFIG_ENV_SIZE, so we must continue to allow all boards to set this value. Update the SPL code to use 200 KB as the default raw U-Boot size directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value. Signed-off-by: Tom Rini <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2022-10-31Rename CONFIG_SYS_TEXT_BASE to CONFIG_TEXT_BASESimon Glass
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE and this makes it imposible to use CONFIG_VAL(). Rename it to resolve this problem. Signed-off-by: Simon Glass <[email protected]>
2022-08-12Convert CONFIG_SYS_FDT_PAD to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_FDT_PAD Signed-off-by: Tom Rini <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2022-07-07Convert CONFIG_SYS_BOOTM_LEN to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_BOOTM_LEN As part of this, rework error handling in boot/bootm.c so that we pass the buffer size to handle_decomp_error as CONFIG_SYS_BOOTM_LEN will not be available to host tools but we do know the size that we passed to malloc(). Cc: Soeren Moch <[email protected]> Signed-off-by: Tom Rini <[email protected]>
2022-07-05Convert CONFIG_PCI_SCAN_SHOW to KconfigTom Rini
This converts the following to Kconfig: CONFIG_PCI_SCAN_SHOW Signed-off-by: Tom Rini <[email protected]>
2022-07-05Convert CONFIG_PCIE1 et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_PCIE1 CONFIG_PCIE2 CONFIG_PCIE3 CONFIG_PCIE4 CONFIG_PCI1 Signed-off-by: Tom Rini <[email protected]>
2022-06-28Globally remove most CONFIG_SPL_BUILD tests from config headersTom Rini
With the exception of how PowerPC handles SPL and TPL (which has its own issues), we cannot safely hide options under CONFIG_SPL_BUILD. Largely remove the places that have this test today. Signed-off-by: Tom Rini <[email protected]>
2022-06-06Convert CONFIG_SPL_TARGET to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SPL_TARGET Signed-off-by: Tom Rini <[email protected]>
2022-06-06Convert CONFIG_SYS_SPL_MALLOC_SIZE et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_SPL_MALLOC_START We introduce a default value here as well, and CONFIG_SYS_SPL_MALLOC to control if we have a malloc pool or not. Signed-off-by: Tom Rini <[email protected]>
2022-06-06Convert CONFIG_SPL_BSS_START_ADDR to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SPL_BSS_START_ADDR Signed-off-by: Tom Rini <[email protected]>
2022-06-06Convert CONFIG_SPL_STACK to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SPL_STACK Signed-off-by: Tom Rini <[email protected]>
2022-06-06Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using system-constants.hTom Rini
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR - Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack pointer directly, otherwise we use the common calculation. - On some platforms that were using the standard calculation but did not set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them. - On a small number of platforms that were not subtracting GENERATED_GBL_DATA_SIZE do so now via the standard calculation. - CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most board config header files. Signed-off-by: Tom Rini <[email protected]>
2022-06-06Convert CONFIG_SPL_BSS_MAX_SIZE et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SPL_BSS_MAX_SIZE CONFIG_SPL_MAX_FOOTPRINT Note that the da850evm platforms were violating the "only use one" rule here, and so now hard-code their BSS limit. Signed-off-by: Tom Rini <[email protected]>
2022-06-06Convert CONFIG_SPL_PAD_TO et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SPL_PAD_TO CONFIG_SPL_MAX_SIZE CONFIG_TPL_PAD_TO CONFIG_TPL_MAX_SIZE Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the existing places. Signed-off-by: Tom Rini <[email protected]>
2022-06-06fsl-layerscape: Remove CONFIG_SPL_PBL_PADTom Rini
This option is not referenced in code, remove it. Signed-off-by: Tom Rini <[email protected]>
2022-06-06Convert CONFIG_SYS_CBSIZE to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_CBSIZE Signed-off-by: Tom Rini <[email protected]>
2022-06-06Convert CONFIG_SYS_MAXARGS to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_MAXARGS Signed-off-by: Tom Rini <[email protected]>
2022-04-25configs: Layerscape: Remove the 'fdt_addr' envHou Zhiqiang
On Layerscape platforms, the DTB is loaded from boot filesystem, per the fdt_addr description in doc/README.distro, it must be removed. Signed-off-by: Hou Zhiqiang <[email protected]> [Rebased] Signed-off-by: Priyanka Jain <[email protected]>
2022-04-21include/configs: drop COUNTER_FREQUENCYPeng Fan
Since we have CONFIG_COUNTER_FREQUENCY enabled, no need COUNTER_FREQUENCY Signed-off-by: Peng Fan <[email protected]>
2022-02-09Convert CONFIG_SCSI_AHCI_PLAT et al to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_SCSI_AHCI_PLAT CONFIG_SYS_SCSI_MAX_SCSI_ID CONFIG_SYS_SCSI_MAX_LUN CONFIG_SYS_SATA_MAX_DEVICE Drop CONFIG_SCSI for everything except the sandbox build. We only need one build for tests. Signed-off-by: Simon Glass <[email protected]> Reviewed-by: Stefan Roese <[email protected]>
2022-02-09scsi: Drop CONFIG_SYS_SCSI_MAX_DEVICESimon Glass
This is defined based on two other CONFIGs for all boards except sandbox and durian. For sandbox the value does not matter. For durian the value seems excessive. Drop the option completely, to simplify configuration and reduce the number of things we need to convert to Kconfig. Signed-off-by: Simon Glass <[email protected]> Reviewed-by: Stefan Roese <[email protected]>
2022-02-09Convert CONFIG_REMAKE_ELF to KconfigAlper Nebi Yasak
This converts the following to Kconfig: CONFIG_REMAKE_ELF Signed-off-by: Alper Nebi Yasak <[email protected]>
2021-12-27Convert CONFIG_CONS_INDEX et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_CONS_INDEX CONFIG_DEBUG_UART_CLOCK CONFIG_FSL_TZPC_BP147 CONFIG_GENERIC_ATMEL_MCI CONFIG_IDENT_STRING CONFIG_LIBATA CONFIG_LNX_KRNL_IMG_TEXT_OFFSET_BASE CONFIG_LPC32XX_GPIO CONFIG_MP CONFIG_MPC8XXX_GPIO CONFIG_MTD_PARTITIONS CONFIG_MVGBE CONFIG_MXC_GPIO CONFIG_NR_DRAM_BANKS CONFIG_OF_BOARD_SETUP CONFIG_OF_STDOUT_VIA_ALIAS CONFIG_OF_SYSTEM_SETUP CONFIG_PREBOOT CONFIG_ROCKCHIP_SERIAL CONFIG_RTC_ENABLE_32KHZ_OUTPUT CONFIG_RTC_MV CONFIG_SCSI_AHCI CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_SPEED CONFIG_SOFT_SPI CONFIG_SPI_FLASH_EON CONFIG_SPI_FLASH_MACRONIX CONFIG_SPI_FLASH_MTD CONFIG_SPI_FLASH_SPANSION CONFIG_SPI_FLASH_SST CONFIG_SPI_FLASH_STMICRO CONFIG_SUPPORT_RAW_INITRD CONFIG_SYS_ARCH_TIMER CONFIG_SYS_BOARD CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE CONFIG_SYS_DCACHE_OFF CONFIG_SYS_FDT_SAVE_ADDRESS CONFIG_SYS_FLASH_CFI CONFIG_SYS_FSL_ERRATUM_ESDHC135 CONFIG_SYS_HAS_SERDES CONFIG_SYS_L2CACHE_OFF CONFIG_SYS_LITTLE_ENDIAN CONFIG_SYS_LOAD_ADDR CONFIG_SYS_MMCSD_FS_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR CONFIG_SYS_NS16550 CONFIG_SYS_PLLFIN CONFIG_SYS_SPI_U_BOOT_OFFS CONFIG_TIMER_SYS_TICK_CH CONFIG_USB_EHCI_FSL CONFIG_U_QE CONFIG_VERSION_VARIABLE Signed-off-by: Tom Rini <[email protected]>
2021-11-09configs: fsl: migrate FMAN/QE specific defines to KconfigRajesh Bhagat
Use moveconfig.py script to convert CONFIG_SYS_FMAN_FW_ADDR, CONFIG_SYS_QE_FW_ADDR and CONFIG_SYS_QE_FMAN_FW_LENGTH to Kconfig and move these entries to defconfigs. Signed-off-by: Rajesh Bhagat <[email protected]> [Rebased] Signed-off-by: Priyanka Jain <[email protected]>
2021-11-05Convert CONFIG_SPL_DRIVERS_MISC et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SPL_DRIVERS_MISC CONFIG_SPL_ENV_SUPPORT CONFIG_SPL_GPIO CONFIG_SPL_I2C CONFIG_SPL_LDSCRIPT CONFIG_SPL_LIBCOMMON_SUPPORT CONFIG_SPL_LIBGENERIC_SUPPORT CONFIG_SPL_LOAD_FIT_ADDRESS CONFIG_SPL_MMC CONFIG_SPL_NAND_SUPPORT CONFIG_SPL_NO_CPU_SUPPORT CONFIG_SPL_OS_BOOT CONFIG_SPL_POWER CONFIG_SPL_STACK_R CONFIG_SPL_STACK_R_ADDR CONFIG_SPL_WATCHDOG CONFIG_SPL_TEXT_BASE Signed-off-by: Tom Rini <[email protected]>
2021-10-06Convert CONFIG_SPL_NAND_LOAD et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SPL_NAND_LOAD CONFIG_SYS_NAND_BLOCK_SIZE CONFIG_SYS_NAND_PAGE_SIZE CONFIG_SYS_NAND_OOBSIZE Signed-off-by: Tom Rini <[email protected]>
2021-10-01serial: Use the default CONFIG_SYS_BAUDRATE_TABLE in more platformsTom Rini
A number of platforms are still defining CONFIG_SYS_BAUDRATE_TABLE to the fallback default of "{ 9600, 19200, 38400, 57600, 115200 }", but with varying whitespace, or were introduced after the default fallback was added. Use the default table here. Signed-off-by: Tom Rini <[email protected]>
2021-08-31Convert CONFIG_SYS_MALLOC_LEN to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_MALLOC_LEN Signed-off-by: Tom Rini <[email protected]> Acked-by: Sean Anderson <[email protected]> Reviewed-by: Rick Chen <[email protected]>
2021-08-31Convert CONFIG_SKIP_LOWLEVEL_INIT et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SKIP_LOWLEVEL_INIT CONFIG_SKIP_LOWLEVEL_INIT_ONLY In order to do this, we need to introduce SPL and TPL variants of these options so that we can clearly disable these options only in SPL in some cases, and both instances in other cases. Signed-off-by: Tom Rini <[email protected]>
2021-08-31Convert CONFIG_SYS_LOAD_ADDR to KconfigTom Rini
Now that we have consistent usage, migrate this symbol to Kconfig. Signed-off-by: Tom Rini <[email protected]> Reviewed-by: Rick Chen <[email protected]>
2021-08-31Convert CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT Signed-off-by: Tom Rini <[email protected]>
2021-08-30arm: Migrate GICV2 / GICV3 to KconfigTom Rini
Migrate CONFIG_GICV2 and CONFIG_GICV3 to Kconfig. We still have the GIC related registers that need to be handled more cleanly but start by moving this symbol to Kconfig. Signed-off-by: Tom Rini <[email protected]>
2021-08-30Convert CONFIG_I2C_SET_DEFAULT_BUS_NUM et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_I2C_SET_DEFAULT_BUS_NUM CONFIG_I2C_DEFAULT_BUS_NUMBER Signed-off-by: Tom Rini <[email protected]>
2021-08-30Convert CONFIG_SYS_I2C_MXC et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_I2C_MXC CONFIG_SYS_I2C_MXC_I2C1 CONFIG_SYS_I2C_MXC_I2C2 CONFIG_SYS_I2C_MXC_I2C3 CONFIG_SYS_I2C_MXC_I2C4 Signed-off-by: Tom Rini <[email protected]>
2021-08-30Convert CONFIG_SYS_I2C_LEGACY to Kconfig and add CONFIG_[ST]PL_SYS_I2C_LEGACYTom Rini
First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig. Next, as you cannot have SYS_I2C_LEGACY and DM_I2C at the same time, introduce CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only in SPL. Finally, for some PowerPC cases we also need CONFIG_TPL_SYS_I2C_LEGACY support. Convert all of the existing users to one or more symbols. Signed-off-by: Tom Rini <[email protected]>
generated by cgit v1.2.3 (git 2.25.1) at 2026-04-13 14:35:48 +0000