| Age | Commit message (Collapse) | Author |
|---|
|
Drop all duplicate newlines from config headers.
No functional change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The recovery-firmware and OpenWrt-NAND do not yet have bootflow
/bootstd entrypoints, so add bootmenu entries to make them
accessible.
Signed-off-by: Mathew McBride <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
The default Ten64 MTD configuration reserves two ubifs partitions
for OpenWrt residing on NAND flash. Add the bootcmd for this system
into the default environment.
Signed-off-by: Mathew McBride <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
The recovery environment[1] on the Ten64 is a OpenWrt-
based ramdisk stored on the NAND intended to help with
system setup tasks.
Before the bootargs were not being set for the recovery
command, relying instead on the existing bootargs variable.
Ensure the bootargs are set correctly prior to booting recovery.
Signed-off-by: Mathew McBride <[email protected]>
[1] https://ten64doc.traverse.com.au/software/recovery/
Reviewed-by: Peng Fan <[email protected]>
|
|
Change the firmware on microSD path to "firmware/traverse/ten64"
as per EBBR section 4.2[1].
The Traverse firmware tools now locate the DPAA2 firmware
and configuration files under that path on the rescue
SD card image.
If a user then installs a standard Linux
distribution over the top of that sdcard, (in theory)
it will be left alone by distribution boot tooling.
Signed-off-by: Mathew McBride <[email protected]>
[1] https://arm-software.github.io/ebbr/index.html#firmware-partition-filesystem
Reviewed-by: Peng Fan <[email protected]>
|
|
The DPAA2 DPL (data plane layout) file was previously
being loaded into 0x80300000, and set to be applied
just before hand off to the kernel.
When a FIT image with a load_address of 0x80000000 was
booted with bootm, the DPL in memory was overwritten.
Move the DPL load to 0x8E000000 (196MiB away from 0x80000000,
and below the other typical load addr of 0x90000000).
Ideally in the future, the DPL lazyapply command
("fsl_mc lazyapply DPL $dpl_addr") should be set to
load the DPL contents into a memory area owned by U-Boot.
Signed-off-by: Mathew McBride <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
Perform a simple rename of CONFIG_EXTRA_ENV_SETTINGS to CFG_EXTRA_ENV_SETTINGS
Signed-off-by: Tom Rini <[email protected]>
|
|
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Since we have CONFIG_COUNTER_FREQUENCY enabled, no need COUNTER_FREQUENCY
Signed-off-by: Peng Fan <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_DIMM_SLOTS_PER_CTLR
Signed-off-by: Tom Rini <[email protected]>
|
|
As the CI test for stopping platforms from being merged that were
defining symbols that had Kconfig entries, a small number of symbols
needed to be migrated again. Do so, and catch two cases the README
should also have been updated but was not.
Signed-off-by: Tom Rini <[email protected]>
|
|
The Ten64 is a networking-oriented MiniITX board
using the NXP LS1088A SoC.
This patch provides the bare minimum to support
Ten64 boards under U-Boot for distroboot.
Some related drivers have not yet been submitted
and this basic support lacks some of the
opinionated defaults provided by our firmware
distribution.
Signed-off-by: Mathew McBride <[email protected]>
[Rebased]
Signed-off-by: Priyanka Jain <[email protected]>
|
