| Age | Commit message (Collapse) | Author |
|---|
|
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
We have a number of platforms that are a combination of a carrier board
and System-on-Module (SoM) that in turn allows for the board to have
different SoCs on it. In some cases, this is handled via board-specific
Kconfig options. In other cases we make use of
CONFIG_SYS_EXTRA_OPTIONS. This latter case however can lead to invalid
configurations as we will not in turn get options that in Kconfig are
selected by or depend on that setting.
To resolve this, make the SoC option a choice in Kconfig and make boards
depend on what they can support. This change opens us up for further
clean-ups in the cases where a single CONFIG_TARGET_xxx can support
different SoCs and today they do not, or do not cleanly do so.
Reported-by: Matt Porter <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: "NXP i.MX U-Boot Team" <[email protected]>
Cc: Soeren Moch <[email protected]>
Cc: Markus Niebel <[email protected]>
Cc: Igor Opaniuk <[email protected]>
Cc: Heiko Schocher <[email protected]>
Cc: Hannes Schmelzer <[email protected]>
Cc: Otavio Salvador <[email protected]>
Cc: Nikita Kiryanov <[email protected]>
Cc: Andreas Geisreiter <[email protected]>
Cc: Ludwig Zenz <[email protected]>
Cc: Lukasz Majewski <[email protected]>
Cc: Akshay Bhat <[email protected]>
Cc: Ken Lin <[email protected]>
Cc: Ian Ray <[email protected]>
Cc: Tim Harvey <[email protected]>
Cc: Jagan Teki <[email protected]>
Cc: Raffaele RECALCATI <[email protected]>
Cc: Simone CIANNI <[email protected]>
Cc: Adam Ford <[email protected]>
Cc: Marcin Niestroj <[email protected]>
Cc: "Eric Bénard" <[email protected]>
Cc: Baruch Siach <[email protected]>
Cc: Jason Liu <[email protected]>
Cc: Ye Li <[email protected]>
Cc: Eric Nelson <[email protected]>
Cc: Troy Kisky <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Parthiban Nallathambi <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: "Sébastien Szymanski" <[email protected]>
Cc: Christian Gmeiner <[email protected]>
Cc: Niel Fourie <[email protected]>
Cc: Martyn Welch <[email protected]>
Cc: Richard Hu <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Boris Brezillon <[email protected]>
Cc: Arkadiusz Karas <[email protected]>
Cc: Breno Lima <[email protected]>
Cc: Francesco Montefoschi <[email protected]>
Cc: Silvio Fricke <[email protected]>
Tested-by: Matt Porter <[email protected]> [colibri_imx6]
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Marcin Niestroj <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART
Note that with this conversion we now have consistent behavior with
respect to ensuring that we have always selected the correct MMC
device and hardware partition.
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_MXC_UART
Signed-off-by: Tom Rini <[email protected]>
Acked-by: Peng Fan <[email protected]>
|
|
Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
Signed-off-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <[email protected]>
|
|
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <[email protected]>
Cc: Joe Hershberger <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Cc: [email protected]
Signed-off-by: Tom Rini <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
Reviewed-by: Simon Goldschmidt <[email protected]>
|
|
We have CONFIG_ENV_SIZE_IS_REDUND but don't really use it. We have one
board where we can simply multiple CONFIG_ENV_SIZE by two for the same
result. The other place where we could but were not previously using
this is for where env_internal.h checks for if we should set
ENV_IS_EMBEDDED. This seems like the most likely use, historically, of
the variable, but it was not used. Add logic to check for this now.
Cc: Wolfgang Denk <[email protected]>
Cc: Joe Hershberger <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_MISC_INIT_R
Signed-off-by: Adam Ford <[email protected]>
[trini: Update the defaults logic slightly]
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC
Signed-off-by: Adam Ford <[email protected]>
Acked-by: Jagan Teki <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_MTD_PARTITIONS
CONFIG_MTD_DEVICE
Signed-off-by: Adam Ford <[email protected]>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <[email protected]>
|
|
CONFIG_HOSTNAME is defined as a "plain" preprocessor string, but every
use is couched by __stringify(...).
Hence, convert it to a proper string option.
Signed-off-by: Mario Six <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_APBH_DMA
CONFIG_APBH_DMA_BURST
CONFIG_APBH_DMA_BURST8
Signed-off-by: Adam Ford <[email protected]>
Reviewed-by: Stefan Agner <[email protected]>
[trini: Add in MMC as well]
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts CONFIG_NAND_MXS to Kconfig.
Signed-off-by: Stefan Agner <[email protected]>
|
|
We move all instances of CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files.
There's a few cases here where we need to expand upon what was in the
header file.
Tested-by: Adam Ford <[email protected]> #omap3_logic
Signed-off-by: Tom Rini <[email protected]>
|
|
Now that the fallback value of CONFIG_SYS_PBSIZE in
include/config_fallbacks.h has been adjusted, remove its definition
from a large number of board configuration files.
Signed-off-by: Thomas Petazzoni <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Alexandru Gagniuc <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Signed-off-by: Alexandru Gagniuc <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
These boards will now use the ksz90x1 driver instead of the mess in
ksz8xxx. This change is needed before the two drivers can be fully
separated.
Signed-off-by: Alexandru Gagniuc <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Migrate all remaining instances of CMD_NAND, CMD_NAND_TRIMFFS
CMD_NAND_LOCK_UNLOCK and CMD_NAND_TORTURE from the headers into the
defconfig files.
Tested-by: Adam Ford <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE
In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.
In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.
There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with
./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC
And then manual updates. This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
The above CONFIG options are in Kconfig, and now have correct depends and
inter-dependencies. Migrate these to configs/ from include/configs/. In the
case of CMD_UBIFS also change it to be a default y if CMD_UBI.
Signed-off-by: Tom Rini <[email protected]>
|
|
The following options are migrated over fully now:
- USB_EHCI_ATMEL
- USB_EHCI_MARVELL
- USB_EHCI_MX6
- USB_EHCI_MX7
- USB_EHCI_MSM
- USB_EHCI_ZYNQ
- USB_EHCI_GENERIC
This also requires fixing the depends on USB_EHCI_MARVELL as it's used
by Orion5X and Kirkwood as well.
Cc: Marek Vasut <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Migrate the rest of the users of CONFIG_USB_EHCI_HCD over to Kconfig.
For a few SoCs, imply or default y this if USB is enabled. In some
cases we had not already migrated to CONFIG_USB so do that as well.
Cc: Marek Vasut <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
In order to be able to migrate the various SoC EHCI CONFIG options we
first need to finish the switch from CONFIG_USB_EHCI to
CONFIG_USB_EHCI_HCD.
Cc: Marek Vasut <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_CMD_BMODE
Signed-off-by: Simon Glass <[email protected]>
[trini: Make this default y and depend on mx5/6/7]
Signed-off-by: Tom Rini <[email protected]>
|
|
In the cases of some boards, a MACH_TYPE number is used which is either
not registered upstream or worse (for functionality) is re-using the
number of a different (or reference) platform instead. Make sure we
have a comment in these cases.
Cc: Albert ARIBAUD <[email protected]>
Cc: Walter Schweizer <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Fabio Estevam <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Acked-by: Stefan Roese <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_BOARD_EARLY_INIT_F
Signed-off-by: Simon Glass <[email protected]>
|
|
move the UBI config options into Kconfig.
Signed-off-by: Heiko Schocher <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Andrew F. Davis <[email protected]>
Reviewed by: Evgeni Dobrev <evgeni at studio-punkt.com>
|
|
In some cases we were missing CONFIG_USB=y so enable that when needed.
Reviewed-by: Masahiro Yamada <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig
Signed-off-by: Tom Rini <[email protected]>
|
|
This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.
Signed-off-by: Tom Rini <[email protected]>
|
|
The driver assumed that I2C1 and I2C2 were always enabled,
and if they were not, then an asynchronous abort was (silently)
raised, to be caught much later on in the Linux kernel.
Fix this by making I2C1 and I2C2 optional just like I2C3 and I2C4
are.
To make the change binary-invariant, declare I2C1 and I2C2 in
every include/configs/ file which defines CONFIG_SYS_I2C_MXC.
Also, while updating README about CONFIG_SYS_I2C_MXC_I2C1 and
CONFIG_SYS_I2C_MXC_I2C2, add missing descriptions for I2C4 speed
(CONFIG_SYS_MXC_I2C4_SPEED) and slave (CONFIG_SYS_MXC_I2C4_SLAVE)
config options.
Signed-off-by: Albert ARIBAUD (3ADEV) <[email protected]>
|
|
Add option to set shell prompt string from menuconfig and migrate
boards globally.
The migration is done as follows:
- Boards that explicitly and unconditionally set CONFIG_SYS_PROMPT had the
entry moved to their defconfig files.
- Boards that defined some kind of #ifdef logic which selects the
CONFIG_SYS_PROMPT (for example qemu-mips) got an #undef CONFIG_SYS_PROMPT
right before the #ifdef logic and were left alone.
- This change forces CONFIG_SYS_PROMPT to be a per board decision, and thus
CONFIG_SYS_PROMPT was removed from all <soc>_common.h and <arch>_common.h
files. This results in a streamlined default value across platforms, and
includes the following files: spear-common, sunxi-common, mv-common,
ti_armv7_common, tegra-common, at91-sama5_common, and zynq-common.
- Boards that relied on <arch/soc>_common.h values of CONFIG_SYS_PROMPT were
not updated in their respective defconfig files under the assumption that
since they did not explicitly define a value, they're fine with whatever
the default is.
- On the other hand, boards that relied on a value defined in some
<boards>_common.h file such as woodburn_common, rpi-common,
bur_am335x_common, ls2085a_common, siemens_am33x_common, and
omap3_evm_common, had their values moved to the respective defconfig files.
- The define V_PROMPT was removed, since it is not used anywhere except for
assigning a value for CONFIG_SYS_PROMPT.
Cc: Tom Rini <[email protected]>
Cc: Masahiro Yamada <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Igor Grinberg <[email protected]>
Signed-off-by: Nikita Kiryanov <[email protected]>
[trini: Add spring, sniper, smartweb to conversion]
Signed-off-by: Tom Rini <[email protected]>
|
|
This also selects CONFIG_NET for any CONFIG_CMD_NET board.
Remove the imx default for CONFIG_NET.
This moves the config that was defined by 60296a8 (commands: add more
command entries in Kconfig).
Signed-off-by: Joe Hershberger <[email protected]>
|
|
Move CONFIG_CMD_CACHE to mx6_common and standardise the way it's defined.
Signed-off-by: Peter Robinson <[email protected]>
Reviewed-by: Tom Rini <trini at konsulko.com>
|
|
Move all standard mx6 MMC configs to mx6_common.
Signed-off-by: Peter Robinson <[email protected]>
Reviewed-by: Tom Rini <trini at konsulko.com>
|
|
Move all standard filesystem, partition and fdt options to mx6_common.
Signed-off-by: Peter Robinson <[email protected]>
|
|
Move generic miscellaneous options that are standard across most, if not all,
mx6 boards to central mx6_common define to ensure consistent features.
Signed-off-by: Peter Robinson <[email protected]>
|
|
Define common LOADADDR and BOOTDELAY to ensure a consistent experience
across mx6 boards
Signed-off-by: Peter Robinson <[email protected]>
|
|
Define CONFIG_MXC_GPIO and CONFIG_CMD_GPIO by default in mx6_common
Signed-off-by: Peter Robinson <[email protected]>
|
|
Define the standard ATAG consfigs in mx6_common.
Signed-off-by: Peter Robinson <[email protected]>
Reviewed-by: Tom Rini <trini at konsulko.com>
|
|
All boards define CONFIG_MX6, CONFIG_DISPLAY_BOARDINFO, CONFIG_DISPLAY_CPUINFO
and CONFIG_SYS_GENERIC_BOARD so define them in mx6_common
Signed-off-by: Peter Robinson <[email protected]>
Reviewed-by: Tom Rini <trini at konsulko.com>
|
|
The linux/sizes.h, asm/arch/imx-regs.h, asm/imx-common/gpio.h,
config_cmd_default.h includes are used fairly universally across imx6 boards
so include them in mx6_common.h by default.
We define CONFIG_SYS_NO_FLASH before config_cmd_default.h so that we
don't have to undef CONFIG_CMD_FLASH / CONFIG_CMD_IMLS everywhere.
Signed-off-by: Peter Robinson <[email protected]>
|
|
Some SoCs have more than two I2C busses. Instead of adding ifdef
to the driver, macros are put into board header file where
CONFIG_SYS_I2C_MXC is defined.
Signed-off-by: York Sun <[email protected]>
CC: Heiko Schocher <[email protected]>
|
|
The CPU errata expressed in include/configs/mx6_common.h apply
to all i.MX6DQ and i.MX6DLS parts.
Signed-off-by: Eric Nelson <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
Acked-by: Stefan Roese <[email protected]>
|
|
Remove platform CONFIG_SYS_HZ definition for configs a-z*.
Signed-off-by: Rob Herring <[email protected]>
|
|
Signed-off-by: Philippe Reynes <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <[email protected]>
|
