summaryrefslogtreecommitdiff
path: root/include/configs/vining_2000.h
AgeCommit message (Collapse)Author
2024-10-11include: Use CONFIG_XPL_BUILD instead of CONFIG_SPL_BUILDSimon Glass
Use the new symbol to refer to any 'SPL' build, including TPL and VPL Signed-off-by: Simon Glass <[email protected]>
2024-08-30imx: Remove CFG_MXC_USB_PORTSCFabio Estevam
The definition of CFG_MXC_USB_PORTSC as (PORT_PTS_UTMI | PORT_PTS_PTW) can be removed from mx5/mx6/mx7/mx8m board config files as it is the default in drivers/usb/host/ehci-mx5.c and drivers/usb/host/ehci-mx6.c. Suggested-by: Tim Harvey <[email protected]> Signed-off-by: Fabio Estevam <[email protected]> Reviewed-by: Tim Harvey <[email protected]>
2024-08-30imx: Remove CFG_MXC_USB_FLAGSFabio Estevam
CFG_MXC_USB_FLAGS is only used for drivers/usb/host/ehci-mx5.c, so it can be removed from all the imx6/imx7/imx8m board config files. mx51evk.h is the only place CFG_MXC_USB_FLAGS is not set to 0. Suggested-by: Tim Harvey <[email protected]> Signed-off-by: Fabio Estevam <[email protected]> Reviewed-by: Marek Vasut <[email protected]> Reviewed-by: Peng Fan <[email protected]>
2022-12-23global: Migrate CONFIG_POWER_PFUZE100_I2C_ADDR to CFGTom Rini
Perform a simple rename of CONFIG_POWER_PFUZE100_I2C_ADDR to CFG_POWER_PFUZE100_I2C_ADDR Signed-off-by: Tom Rini <[email protected]>
2022-12-23global: Migrate CONFIG_PCIE_IMX_PERST_GPIO to CFGTom Rini
Perform a simple rename of CONFIG_PCIE_IMX_PERST_GPIO to CFG_PCIE_IMX_PERST_GPIO Signed-off-by: Tom Rini <[email protected]>
2022-12-23global: Migrate CONFIG_MXC_USB_FLAGS et al to CFGTom Rini
Perform simple renames of: CONFIG_MXC_USB_FLAGS to CFG_MXC_USB_FLAGS CONFIG_MXC_USB_PORT to CFG_MXC_USB_PORT CONFIG_MXC_USB_PORTSC to CFG_MXC_USB_PORTSC Signed-off-by: Tom Rini <[email protected]>
2022-12-23global: Migrate CONFIG_MXC_UART_BASE to CFGTom Rini
Perform a simple rename of CONFIG_MXC_UART_BASE to CFG_MXC_UART_BASE Signed-off-by: Tom Rini <[email protected]>
2022-12-23global: Migrate CONFIG_IMX6_PWM_PER_CLK to CFGTom Rini
Perform a simple rename of CONFIG_IMX6_PWM_PER_CLK to CFG_IMX6_PWM_PER_CLK Signed-off-by: Tom Rini <[email protected]>
2022-12-23global: Migrate CONFIG_FEC_MXC_PHYADDR to CFGTom Rini
Perform a simple rename of CONFIG_FEC_MXC_PHYADDR to CFG_FEC_MXC_PHYADDR Signed-off-by: Tom Rini <[email protected]>
2022-12-05Convert CONFIG_POWER_LTC3676 et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_POWER_FSL CONFIG_POWER_FSL_MC13892 CONFIG_POWER_HI6553 CONFIG_POWER_LTC3676 CONFIG_POWER_PFUZE100 CONFIG_POWER_PFUZE3000 CONFIG_POWER_SPI CONFIG_POWER_TPS65090_EC CONFIG_POWER_TPS65218 CONFIG_POWER_TPS65910 Signed-off-by: Tom Rini <[email protected]>
2022-12-05global: Move remaining CONFIG_SYS_* to CFG_SYS_*Tom Rini
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do not easily transition to Kconfig. In many cases they likely should come from the device tree instead. Move these out of CONFIG namespace and in to CFG namespace. Signed-off-by: Tom Rini <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2022-12-05global: Move remaining CONFIG_SYS_SDRAM_* to CFG_SYS_SDRAM_*Tom Rini
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM namespace do not easily transition to Kconfig. In many cases they likely should come from the device tree instead. Move these out of CONFIG namespace and in to CFG namespace. Signed-off-by: Tom Rini <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2022-12-05imx6/imx7: Remove now empty imx6_spl.h and imx7_spl.hTom Rini
There are now no flags being set in these files, so remove them. Signed-off-by: Tom Rini <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2022-11-10global: Migrate CONFIG_SYS_FSL* symbols to the CFG_SYS namespaceTom Rini
Migrate all of COFIG_SYS_FSL* to the CFG_SYS namespace. Signed-off-by: Tom Rini <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2022-07-05Convert CONFIG_PCI_SCAN_SHOW to KconfigTom Rini
This converts the following to Kconfig: CONFIG_PCI_SCAN_SHOW Signed-off-by: Tom Rini <[email protected]>
2022-07-05Convert CONFIG_PCIE_IMX to KconfigTom Rini
This converts the following to Kconfig: CONFIG_PCIE_IMX Signed-off-by: Tom Rini <[email protected]>
2022-06-28Convert CONFIG_USB_MAX_CONTROLLER_COUNT to KconfigTom Rini
This converts the following to Kconfig: CONFIG_USB_MAX_CONTROLLER_COUNT Signed-off-by: Tom Rini <[email protected]>
2022-06-28Convert CONFIG_EHCI_HCD_INIT_AFTER_RESET to KconfigTom Rini
This converts the following to Kconfig: CONFIG_EHCI_HCD_INIT_AFTER_RESET Signed-off-by: Tom Rini <[email protected]>
2022-06-06Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using system-constants.hTom Rini
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR - Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack pointer directly, otherwise we use the common calculation. - On some platforms that were using the standard calculation but did not set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them. - On a small number of platforms that were not subtracting GENERATED_GBL_DATA_SIZE do so now via the standard calculation. - CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most board config header files. Signed-off-by: Tom Rini <[email protected]>
2022-04-21configs: imx: drop IMX_FEC_BASEPeng Fan
IMX_FEC_BASE is not used in these boards, so drop it. Reviewed-by: Fabio Estevam <[email protected]> Signed-off-by: Peng Fan <[email protected]>
2022-03-18net: fec_mxc: Drop CONFIG_FEC_XCV_TYPETom Rini
With all boards now using DM_ETH we determine the value for CONFIG_FEC_XCV_TYPE at run time, except in the case of the default fall-back. Set the fallback directly now. Cc: Fabio Estevam <[email protected]> Cc: Ramon Fried <[email protected]> Cc: Stefano Babic <[email protected]> Signed-off-by: Tom Rini <[email protected]>
2022-03-18Convert CONFIG_ETHPRIME to KconfigTom Rini
This converts the following to Kconfig: CONFIG_ETHPRIME This is also done by adding a gating Kconfig option, CONFIG_USE_ETHPRIME similar to other options that are not always set and control environment variables. Signed-off-by: Tom Rini <[email protected]>
2021-09-04i2c: Convert CONFIG_POWER_I2C et al to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_POWER_I2C CONFIG_POWER_LEGACY They are handled at the same time due to a dependency between them. Update the Makefile rule to use legacy power only in U-Boot proper. Unfortunately a separate rule is needed in SPL to be able to build legacy power. Add SPL related symbols for both, to allow for SPL-only usage. Signed-off-by: Simon Glass <[email protected]> Reviewed-by: Jaehoon Chung <[email protected]> [trini: More SPL related cleanups, reword commit message] Signed-off-by: Tom Rini <[email protected]>
2021-09-04power: Rename CONFIG_POWER to CONFIG_POWER_LEGACYSimon Glass
This option is used in pre-driver model code and much of it has never been converted to driver model. We want to add a new option to enable power support, so we can use a simple rule in the Makefile. Rename this one, which is really about a particular implementation of power. Also update the pmic.h header file so it either includes the legacy API or the driver model one. Signed-off-by: Simon Glass <[email protected]> Reviewed-by: Jaehoon Chung <[email protected]>
2021-08-31Convert CONFIG_SYS_MALLOC_LEN to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_MALLOC_LEN Signed-off-by: Tom Rini <[email protected]> Acked-by: Sean Anderson <[email protected]> Reviewed-by: Rick Chen <[email protected]>
2021-08-30Convert CONFIG_SYS_I2C_MXC et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_I2C_MXC CONFIG_SYS_I2C_MXC_I2C1 CONFIG_SYS_I2C_MXC_I2C2 CONFIG_SYS_I2C_MXC_I2C3 CONFIG_SYS_I2C_MXC_I2C4 Signed-off-by: Tom Rini <[email protected]>
2021-08-30Convert CONFIG_SYS_I2C_SPEED et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_I2C_SPEED CONFIG_SYS_I2C_SLAVE Signed-off-by: Tom Rini <[email protected]>
2021-08-30Convert CONFIG_SYS_I2C_LEGACY to Kconfig and add CONFIG_[ST]PL_SYS_I2C_LEGACYTom Rini
First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig. Next, as you cannot have SYS_I2C_LEGACY and DM_I2C at the same time, introduce CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only in SPL. Finally, for some PowerPC cases we also need CONFIG_TPL_SYS_I2C_LEGACY support. Convert all of the existing users to one or more symbols. Signed-off-by: Tom Rini <[email protected]>
2021-07-28i2c: Rename CONFIG_SYS_I2C to CONFIG_SYS_I2C_LEGACYSimon Glass
It is quite confusing that CONFIG_SYS_I2C selects the legacy I2C and CONFIG_DM_I2C selects the current I2C. The deadline to migrate I2C is less than a year away. Also we want to have a CONFIG_I2C for U-Boot proper just like we have CONFIG_SPL_I2C for SPL, so we can simplify the Makefile rules. Rename this symbol so it is clear it is going away. Signed-off-by: Simon Glass <[email protected]> Reviewed-by: Heiko Schocher <[email protected]>
2020-12-07configs: migrate CONFIG_IMX_THERMAL to defconfigsTom Rini
Done via moveconfig.py Signed-off-by: Tom Rini <[email protected]>
2020-08-08Convert CONFIG_SYS_MMC_ENV_DEV et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_MMC_ENV_DEV CONFIG_SYS_MMC_ENV_PART Note that with this conversion we now have consistent behavior with respect to ensuring that we have always selected the correct MMC device and hardware partition. Signed-off-by: Tom Rini <[email protected]>
2020-05-08treewide: mem: Move mtest related defines to KconfigAshok Reddy Soma
Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: Ashok Reddy Soma <[email protected]> Signed-off-by: Michal Simek <[email protected]> [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: Tom Rini <[email protected]>
2020-04-28Convert CONFIG_PHYLIB et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_PHYLIB CONFIG_BITBANGMII CONFIG_MV88E6352_SWITCH CONFIG_MV88E61XX_SWITCH CONFIG_PHYLIB_10G CONFIG_PHY_AQUANTIA CONFIG_PHY_ATHEROS CONFIG_PHY_BROADCOM CONFIG_PHY_CORTINA CONFIG_PHY_DAVICOM CONFIG_PHY_ET1011C CONFIG_PHY_LXT CONFIG_PHY_MARVELL CONFIG_PHY_MICREL CONFIG_PHY_NATSEMI CONFIG_PHY_REALTEK CONFIG_RTL8211X_PHY_FORCE_MASTER CONFIG_PHY_SMSC CONFIG_PHY_TERANETICS CONFIG_PHY_TI CONFIG_PHY_VITESSE CONFIG_PHY_XILINX Signed-off-by: Tom Rini <[email protected]>
2020-01-20ARM: imx: vining2000: Enable SPL SDP by defaultMarek Vasut
Enable SPL SDP fallback boot option in default build. Signed-off-by: Marek Vasut <[email protected]> Cc: Fabio Estevam <[email protected]> Cc: Silvio Fricke <[email protected]> Cc: Stefano Babic <[email protected]>
2019-12-06ARM: imx: vining2000: Convert to ethernet DMMarek Vasut
Convert the board to ethernet DM support. Adjust board file accordingly, as the board_eth_init() contains custom clock configuration required for this board to work. Furthermore, enable FEC1 clock to make FEC1 work as well. Signed-off-by: Marek Vasut <[email protected]> Cc: Fabio Estevam <[email protected]> Cc: Silvio Fricke <[email protected]> Cc: Stefano Babic <[email protected]>
2019-12-06ARM: imx: vining2000: Convert to SPL frameworkMarek Vasut
In preparation for use of DDR DRAM fine-tuning upon boot, convert the board to SPL framework instead of using DCD tables to bring up DRAM and pinmux. Signed-off-by: Marek Vasut <[email protected]> Cc: Fabio Estevam <[email protected]> Cc: Silvio Fricke <[email protected]> Cc: Stefano Babic <[email protected]>
2019-11-20env: Finish migration of common ENV optionsTom Rini
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <[email protected]> Cc: Joe Hershberger <[email protected]> Cc: Patrick Delaunay <[email protected]> Cc: [email protected] Signed-off-by: Tom Rini <[email protected]> Acked-by: Joe Hershberger <[email protected]> Reviewed-by: Simon Goldschmidt <[email protected]>
2019-11-20env: Remove useless CONFIG_ENV_SIZE_REDUND and fix ENV_IS_REDUND checkTom Rini
We have CONFIG_ENV_SIZE_IS_REDUND but don't really use it. We have one board where we can simply multiple CONFIG_ENV_SIZE by two for the same result. The other place where we could but were not previously using this is for where env_internal.h checks for if we should set ENV_IS_EMBEDDED. This seems like the most likely use, historically, of the variable, but it was not used. Add logic to check for this now. Cc: Wolfgang Denk <[email protected]> Cc: Joe Hershberger <[email protected]> Signed-off-by: Tom Rini <[email protected]> Reviewed-by: Simon Glass <[email protected]> Acked-by: Joe Hershberger <[email protected]>
2019-07-19pwm: imx: add Kconfig supportHeiko Schocher
add Kconfig support for this driver. Signed-off-by: Heiko Schocher <[email protected]> Acked-by: Martyn Welch <[email protected]>
2019-06-11ARM: imx: vining2000: Enable DM SerialMarek Vasut
Enable DM Serial support on iMX6SX VINING|2000. Signed-off-by: Marek Vasut <[email protected]> Cc: Fabio Estevam <[email protected]> Cc: Silvio Fricke <[email protected]> Cc: Stefano Babic <[email protected]>
2019-05-04Convert CONFIG_SUPPORT_EMMC_BOOT to KconfigAlex Kiernan
This converts the following to Kconfig: CONFIG_SUPPORT_EMMC_BOOT As requested by Michal Simek <[email protected]>, these boards have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated: xilinx_zynqmp_zc1275_revB xilinx_zynqmp_zc1751_xm018_dc4 xilinx_zynqmp_zc1751_xm019_dc5 xilinx_zynqmp_zcu100_revC xilinx_zynqmp_zcu102_rev1_0 xilinx_zynqmp_zcu102_revA xilinx_zynqmp_zcu102_revB xilinx_zynqmp_zcu104_revA xilinx_zynqmp_zcu104_revC xilinx_zynqmp_zcu106_revA xilinx_zynqmp_zcu111_revA Signed-off-by: Alex Kiernan <[email protected]> Acked-by: Lukasz Majewski <[email protected]> Acked-by: Patrick Delaunay <[email protected]> Acked-by: Ramon Fried <[email protected]> Reviewed-by: Andy Shevchenko <[email protected]> Tested-by: Sébastien Szymanski <[email protected]>
2018-08-17Convert CONFIG_MII et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford <[email protected]> Acked-by: Jagan Teki <[email protected]> Acked-by: Joe Hershberger <[email protected]>
2018-08-16configs: Migrate CONFIG_NR_DRAM_BANKSTom Rini
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <[email protected]>
2018-05-23Convert CONFIG_SUPPORT_EMMC_RPMB to KconfigAlex Kiernan
Convert CONFIG_SUPPORT_EMMC_RPMB to Kconfig. Split the command handling from the underlying support and expose this through CMD_MMC_RPMB. Signed-off-by: Alex Kiernan <[email protected]>
2018-05-07SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <[email protected]>
2018-04-08Migrate CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to KconfigAlex Kiernan
Convert CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig Signed-off-by: Alex Kiernan <[email protected]> Reviewed-by: Lukasz Majewski <[email protected]> Reviewed-by: Petr Vorel <[email protected]> Reviewed-by: Petr Vorel <petr.vorel at gmail.com>
2017-09-08usb: net: migrate USB Ethernet adapters to KconfigChris Packham
This migrates ASIX, ASIX88179, MCS7830, RTL8152 and SMSC95XX to Kconfig. Update defconfigs. Signed-off-by: Chris Packham <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2017-09-08usb: net: migrate CONFIG_USB_HOST_ETHER to KconfigChris Packham
CONFIG_USB_HOST_ETHER is the framework that the drivers are dependent on USB_HOST_ETHER. Use this as a menu and move the existing LAN75XX and LAN78XX options under new menu. Finally update the defconfigs that need CONFIG_USB_HOST_ETHER. Signed-off-by: Chris Packham <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2017-08-11Convert CONFIG_CMD_PCI to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_CMD_PCI Signed-off-by: Simon Glass <[email protected]> Reviewed-by: Bin Meng <[email protected]> Reviewed-by: Philipp Tomsich <[email protected]>
2017-08-07Move PHYLIB to KconfigAlexandru Gagniuc
Signed-off-by: Alexandru Gagniuc <[email protected]> Acked-by: Joe Hershberger <[email protected]>
generated by cgit v1.2.3 (git 2.25.1) at 2026-04-12 15:03:33 +0000