| Age | Commit message (Collapse) | Author |
|---|
|
This converts the following to Kconfig:
CONFIG_IOMUX_LPSR
CONFIG_IOMUX_SHARE_CONF_REG
Signed-off-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Try to maintain some consistency between these variables by using _plat as
a suffix for them.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Some places use __ASSEMBLER__ instead which does not work since the
Makefile does not define it. Fix them.
Signed-off-by: Simon Glass <[email protected]>
|
|
It is bad practice to include common.h in other header files since it can
bring in any number of superfluous definitions. It implies that some C
files don't include it and thus may be missing CONFIG options that are set
up by that file. The C files should include these themselves.
Update some header files in arch/arm to drop this.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add support for Vybrid's UART2 (Colibri UART_B).
Signed-off-by: Stefan Agner <[email protected]>
Acked-by: Marcel Ziswiler <[email protected]>
|
|
The DDR memory controller include file for the Vybrid uses
iomux_v3_cfg_t without actually including iomux-vf610.h.
Signed-off-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Igor Opaniuk <[email protected]>
|
|
This code allows reusing the default u-boot as in the late board init, the
default envs are restored and proper recovery scripts executed.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
Provide function to enable I2C clocks for vf610 - in the generic code.
This function overrides the default weak function implementation (which
only returns 1).
Signed-off-by: Lukasz Majewski <[email protected]>
Tested-by: Marcel Ziswiler <[email protected]>
|
|
This commit provides extra defines needed for DDR memory controller
calibration (read leveling performing).
Signed-off-by: Lukasz Majewski <[email protected]>
Reviewed-by: Stefan Agner <[email protected]>
|
|
The CR80 register has multiple interrupt bits, the code is supposed
to check bit 8 but instead uses a logical and. In most cases this
probably did not affect real operations since at that stage typically
none of the other bits are set.
Signed-off-by: Stefan Agner <[email protected]>
Acked-by: Marcel Ziswiler <[email protected]>
|
|
According to the data sheet bits 10-8 are PHYDRAM_CK_EN. Fix mask
to allow setting PHYDRAM_CK_EN correctly.
Signed-off-by: Stefan Agner <[email protected]>
Acked-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
|
|
The Vybrid reference manual VFXXXRM Rev. 0 10/2016 states in chapter
5.2.6.1 DUMMY PADS (DDR/QuadSPI) that those pads need to be programed
for correct operation of DDR. Assume the default DDR pin configuration
which seems to work well on a Colibri VF50.
Signed-off-by: Stefan Agner <[email protected]>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <[email protected]>
|
|
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.
This change is also coherent with the structure in kernel.
Signed-off-by: Stefano Babic <[email protected]>
CC: Fabio Estevam <[email protected]>
CC: Akshay Bhat <[email protected]>
CC: Ken Lin <[email protected]>
CC: Marek Vasut <[email protected]>
CC: Heiko Schocher <[email protected]>
CC: "Sébastien Szymanski" <[email protected]>
CC: Christian Gmeiner <[email protected]>
CC: Stefan Roese <[email protected]>
CC: Patrick Bruenn <[email protected]>
CC: Troy Kisky <[email protected]>
CC: Nikita Kiryanov <[email protected]>
CC: Otavio Salvador <[email protected]>
CC: "Eric Bénard" <[email protected]>
CC: Jagan Teki <[email protected]>
CC: Ye Li <[email protected]>
CC: Peng Fan <[email protected]>
CC: Adrian Alonso <[email protected]>
CC: Alison Wang <[email protected]>
CC: Tim Harvey <[email protected]>
CC: Martin Donnelly <[email protected]>
CC: Marcin Niestroj <[email protected]>
CC: Lukasz Majewski <[email protected]>
CC: Adam Ford <[email protected]>
CC: "Albert ARIBAUD (3ADEV)" <[email protected]>
CC: Boris Brezillon <[email protected]>
CC: Soeren Moch <[email protected]>
CC: Richard Hu <[email protected]>
CC: Wig Cheng <[email protected]>
CC: Vanessa Maegima <[email protected]>
CC: Max Krummenacher <[email protected]>
CC: Stefan Agner <[email protected]>
CC: Markus Niebel <[email protected]>
CC: Breno Lima <[email protected]>
CC: Francesco Montefoschi <[email protected]>
CC: Jaehoon Chung <[email protected]>
CC: Scott Wood <[email protected]>
CC: Joe Hershberger <[email protected]>
CC: Anatolij Gustschin <[email protected]>
CC: Simon Glass <[email protected]>
CC: "Andrew F. Davis" <[email protected]>
CC: "Łukasz Majewski" <[email protected]>
CC: Patrice Chotard <[email protected]>
CC: Nobuhiro Iwamatsu <[email protected]>
CC: Hans de Goede <[email protected]>
CC: Masahiro Yamada <[email protected]>
CC: Stephen Warren <[email protected]>
CC: Andre Przywara <[email protected]>
CC: "Álvaro Fernández Rojas" <[email protected]>
CC: York Sun <[email protected]>
CC: Xiaoliang Yang <[email protected]>
CC: Chen-Yu Tsai <[email protected]>
CC: George McCollister <[email protected]>
CC: Sven Ebenfeld <[email protected]>
CC: Filip Brozovic <[email protected]>
CC: Petr Kulhavy <[email protected]>
CC: Eric Nelson <[email protected]>
CC: Bai Ping <[email protected]>
CC: Anson Huang <[email protected]>
CC: Sanchayan Maity <[email protected]>
CC: Lokesh Vutla <[email protected]>
CC: Patrick Delaunay <[email protected]>
CC: Gary Bisson <[email protected]>
CC: Alexander Graf <[email protected]>
CC: [email protected]
Reviewed-by: Fabio Estevam <[email protected]>
Reviewed-by: Christian Gmeiner <[email protected]>
|
|
The Vybrid SoC family has the same display controller unit (DCU)
like the LS1021A SoC. This patch adds platform data, pinmux defines
and clock control to enable the driver for Toradex Colibri Vybrid
module.
Signed-off-by: Stefan Agner <[email protected]>
Signed-off-by: Sanchayan Maity <[email protected]>
Reviewed-by: Stefano Babic <[email protected]>
|
|
Drop CONFIG_LPUART_32B_REG.
Move the register structure to a common file include/fsl_lpuart.h
Define lpuart_serial_platdata structure which includes the reg base and flags.
For 32Bit register access, use lpuart_read32/lpuart_write32 which handles
big/little endian.
For 8Bit register access, still use the orignal code.
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by : Stefano Babic <[email protected]>
Cc: Bhuvanchandra DV <[email protected]>
Cc: York Sun <[email protected]>
Cc: Shaohui Xie <[email protected]>
Cc: Alison Wang <[email protected]>
|
|
During very early boot-ROM execution the pinmux
configuration isi in Hi-Z state. If pull-up is enabled
on GPIO pad's there will be a short period of toggle
from high to low on the IO when GPIO is set low during
boot. To avoid this glitch, disable pull-up configuration
in GPIO pinmux.
Signed-off-by: Bhuvanchandra DV <[email protected]>
|
|
The VF610 DDRMC driver code contains settings which are
board-specific. Move these out to boards so that new boards
can define their own without having to modify the driver.
Signed-off-by: Albert ARIBAUD (3ADEV) <[email protected]>
|
|
Add support in mxc_i2c driver, iomux_v3 and vf610 architecture for the four
I2C instances available in VF610.
Signed-off-by: Albert ARIBAUD (3ADEV) <[email protected]>
|
|
Add IOMUX for the pad used as USB pen. This needs to be driven low for
the Iris and Viola boards where it is pulled up high by default. This is
required for the USB host functionality to work on these boards. Use the
board specific weak initialisation function, to drive the pin low which
would be called on "usb start".
Signed-off-by: Sanchayan Maity <[email protected]>
|
|
Add iomux definitions for DSPI second instance.
Signed-off-by: Bhuvanchandra DV <[email protected]>
|
|
Signed-off-by: Bhuvanchandra DV <[email protected]>
|
|
Inorder to use the pins as GPIO, apart from setting the alt-function,
pinmuxing need to be done, this patch adds pinmux entries of
few GPIOs.
Acked-by: Stefan Agner <[email protected]>
Signed-off-by: Bhuvanchandra DV <[email protected]>
|
|
Add GPIO driver support to Freescale VF610
Signed-off-by: Bhuvanchandra DV <[email protected]>
|
|
rework and unify i2c address names for different SoCs, which
use the mxc_i2c driver.
Signed-off-by: Heiko Schocher <[email protected]>
|
|
This driver adds support for the USB peripheral on Freescale Vybrid
SoC's.
Signed-off-by: Sanchayan Maity <[email protected]>
|
|
This adds initial support for Colibri VF50/VF61 based on Freescale
Vybrid SoC.
- CPU clocked at 396/500 MHz
- DDR3 at 396MHz
- for VF50, use PLL2 as memory clock (synchronous mode)
- for VF61, use PLL1 as memory clock (asynchronous mode)
- Console on UART0 (Colibri UART_A)
- Ethernet on FEC1
- PLL5 based RMII clocking (E.g. No external crystal)
- UART_A and UART_C I/O muxing
- Boot from NAND by default
Tested on Colibri VF50/VF61 booting using serial loader over UART.
Signed-off-by: Sanchayan Maity <[email protected]>
Acked-by: Stefan Agner <[email protected]>
|
|
Vybrid product family consists of several rather similar SoC which
can be determined by softare during boot time. This allows use of
variable ${soc} for Linux device tree files. Detect VF5xx CPU's by
reading the CPU count register. We can determine the second number
of the CPU type (VF6x0) which indicates the presence of a L2 cache.
Signed-off-by: Stefan Agner <[email protected]>
Signed-off-by: Sanchayan Maity <[email protected]>
|
|
Enable the SCSC (Slow Clock Source Controller) and select the external
32KHz oscillator. This improves the accuracy of the RTC.
Signed-off-by: Sanchayan Maity <[email protected]>
|
|
In order to avoid code duplication, move the DDR3 initialization to the
common place under imx-common. Currently ROW_DIFF and COL_DIFF can be
chosen from the board file. The JEDEC timings are specified using a
common ddr3_jedec_timings structure.
Signed-off-by: Stefan Agner <[email protected]>
Signed-off-by: Sanchayan Maity <[email protected]>
|
|
Improve the evaluation of the reset source. Bit description according
to latest reference manual rev. 7.
Signed-off-by: Stefan Agner <[email protected]>
|
|
Removed settings in unsupported register fields. They didn’t
do anything, and in most cases, were not documented in the
reference manual.
Changed register settings to comply with JEDEC required values.
Changed timing parameters because they included full clock
periods that were doing nothing.
Signed-off-by: Anthony Felice <[email protected]>
[rebased on v2014.10-rc2]
Signed-off-by: Stefan Agner <[email protected]>
|
|
Add NFC (NAND Flash Controller) clock support and enable them
at board initialization time.
Signed-off-by: Stefan Agner <[email protected]>
|
|
Add pin mux for NAND Flash Controller (NFC). NAND can be connected
using 8 or 16 data lines, this patch adds pin mux entries for all
16 data lines.
Signed-off-by: Stefan Agner <[email protected]>
|
|
Add QSPI support for VF610TWR, such as clock and iomux.
Signed-off-by: Alison Wang <[email protected]>
Signed-off-by: Chao Fu <[email protected]>
|
|
Set DDR_SEL_PAD_CONTR register explicitly to DDR3 which solves RAM
issues with newer silicon (1.1). This register was added in revision
4 of the Vybrid Reference Manual.
Signed-off-by: Stefan Agner <[email protected]>
|
|
This patch contains several changes required for second Ethernet
(enet1/RMII1) port on vf610
- ANADIG PLL5 control definitions required for Ethernet RMII1 clock
- Secondary Ethernet (enet1) MAC RMII1 base address definition
- RMII1 iomux definitions
- VF610_PAD_PTA6__RMII0_CLKOUT iomux definition required for
internal (e.g. crystal-less) Ethernet clocking.
Signed-off-by: Marcel Ziswiler <[email protected]>
[[email protected]: regrouped patch]
Signed-off-by: Stefan Agner <[email protected]>
|
|
Add CCM_CCGR0_UART0_CTRL_MASK clock definition and add TX/RX iomux
definitions for UART0 (aka. SCI0).
Signed-off-by: Marcel Ziswiler <[email protected]>
[[email protected]: regrouped patch]
Signed-off-by: Stefan Agner <[email protected]>
|
|
The anadig_reg structure started at the wrong offset (fixed by adding
reserved_0x000[4]), was missing some reserved field required for
alignment purpose (reserved_0x094[3] between pll4_denom and pll6_ctrl)
and further contained a too short reserved field causing further miss-
alignment (reserved_0x0C4[7]). Also, rename all the reserved fields
and using a memory offset based scheme for.
Discovered and tested by temporarily putting the following debug
instrumentation into board_init():
struct anadig_reg *anadig = (struct anadig_reg *)ANADIG_BASE_ADDR;
printf("&anadig->pll3_ctrl=0x%p\n", &anadig->pll3_ctrl);
printf("&anadig->pll5_ctrl=0x%p\n", &anadig->pll5_ctrl);
Signed-off-by: Marcel Ziswiler <[email protected]>
[[email protected]: regrouped patch]
Signed-off-by: Stefan Agner <[email protected]>
|
|
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.
Conflicts:
board/sandburst/common/ppc440gx_i2c.c
board/sandburst/common/ppc440gx_i2c.h
Signed-off-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <[email protected]>
|
|
This patch adds I2C support for Vybrid VF610 platform and adds
I2C0 support to VF610TWR board.
Signed-off-by: Alison Wang <[email protected]>
|
|
This patch adds generic codes to support Freescale's Vybrid VF610 CPU.
It aligns Vybrid VF610 platform with i.MX platform. As there are
some differences between VF610 and i.MX platforms, the specific
codes are in the arch/arm/cpu/armv7/vf610 directory.
Signed-off-by: Alison Wang <[email protected]>
Reviewed-by: Benoît Thébaudeau <[email protected]>
|
