| Age | Commit message (Collapse) | Author |
|---|
|
Add Renesas R-Car R8A78000 X5H CPG clock driver, which serves as a
remap driver between DT clock IDs and SCMI clock IDs in case U-Boot
runs on the Cortex-A, and as a trivial clock driver for RSIP.
The R-Car X5H SCP firmware uses different SCMI clock IDs in different
versions of the SCP firmware, which makes this remapping necessary.
The SCMI base protocol version is updated for each new SCP firmware
version, it is therefore possible to determine which SCP firmware
version is running on the platform from the base protocol and then
determine which remapping table to use for DT clock ID to SCMI clock
ID remapping.
Currently supported versions are SCP 4.28, 4.31, 4.32 .
The DT clock ID to SCMI clock ID remap and call mechanism is a bit
complex. The driver looks up the SCMI clock protocol device on probe
and stores pointer to it in private data. On each clock request which
has to be remapped, the device sequence ID of this SCMI clock protocol
device is incremented by the remapped SCMI clock ID + 1 and used to
look up matching clock device by sequence number. If the device is
found, it is converted to clock, which can be used in regular clock
operations. This look up has to be done because the SCMI clock driver
registers a subdevice for each clock, and this look up is the only way
to find the correct SCMI clock subdevice. Since the SCMI device and
the clock subdevices are registered in the same function, we can depend
on the device sequence numbers to be monotonically incrementing, with
SCMI clock protocol device being sequence number N, the first SCMI
clock subdevice being sequence number N+1 and so on.
In case of RSIP, all clocks are already enabled by BootROM or early
SoC initialization code, the driver therefore only acts as a stub.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The current state of SCP on Renesas R-Car Gen5 is not yet final and
is still missing full clock control, the clock control is exposed as
separate enable/disable and rate controls.
Temporarily introduce custom local compound clock, which are used as
an adaptation layer between U-Boot clock tree and current state of
SCP, and which bind two SCP clock into a single compound clock, which
provides both enable/disable and rate controls.
This is mainly meant to be used by SD/eMMC controller, to allow the
driver to both turn its clock on and off, and also obtain the current
clock rate. This is going to be removed once the SCP clock protocol
solidifies.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Add clock tables for R8A779H0 V4M SoC.
The current version is imported from:
https://lore.kernel.org/linux-renesas-soc/c678ef7164e3777fa91572f72e47ef385cea64b8.1706194617.git.geert+renesas@glider.be/
The current version still contains PLL7 extras from the
previous version to provide ethernet support in U-Boot.
Signed-off-by: Hai Pham <[email protected]>
|
|
This driver provides clock and reset control for the Renesas R9A07G044L
(RZ/G2L) and R9A07G044C (RZ/G2LC) SoC. It consists of two parts:
* driver code which is applicable to all SoCs in the RZ/G2L family.
* static data describing the clocks and resets which are specific to the
R9A07G044{L,C} SoCs. The identifier r9a07g044 (without a final letter)
is used to indicate that both SoCs are supported.
clk_set_rate() and clk_get_rate() are implemented only for the clocks
that are actually used in u-boot.
The CPG driver is marked with DM_FLAG_PRE_RELOC to ensure that its bind
function is called before the SCIF (serial port) driver is probed. This
is required so that we can de-assert the relevant reset signal during
the serial driver probe function.
This patch is based on the corresponding Linux v6.5 driver
(commit 52e12027d50affbf60c6c9c64db8017391b0c22e).
Signed-off-by: Paul Barker <[email protected]>
Reviewed-by: Biju Das <[email protected]>
Reviewed-by: Lad Prabhakar <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Clock driver for the Renesas RZ/N1 SoC family. This is based on
Linux kernel 6.2.y drivers/clk/renesas/r9a06g032-clocks.c as found in
commit 02693e11611e ("clk: renesas: r9a06g032: Repair grave increment error"),
with the following additional patch series applied:
https://lore.kernel.org/linux-renesas-soc/[email protected]/
Notable difference: this version avoids allocating a 'struct clk'
for each clock source, as this is problematic before relocation.
Instead, it uses the same approach as existing Renesas R-Car Gen2/3
clock drivers, using a temporary structure filled on-the-fly.
Signed-off-by: Ralph Siemsen <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Add new CONFIG_CLK_RCAR to control compilation of shared code for R-Car
clock drivers (renesas-cpg-mssr.c). Enable this for R-Car Gen2 and 3.
This is necessary so that CONFIG_CLK_RENESAS can be enabled, allowing
recursion into the drivers/clk/reneasas directory, without bringing in
the R-Car support code. The support code contains platform specific
access (TMU_BASE) which is not needed on other Renesas devices such as
RZ/N1.
Signed-off-by: Ralph Siemsen <[email protected]>
Reviewed-by: Sean Anderson <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Add clock tables for R8A779G0 V4H SoC from Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
There is an adjustment to the clock tables to make them easier suitable
for U-Boot, PLL2 is not treated as GEN4 PLL type PLL2_VAR, but rather a
plain PLL2. This should be sufficient until PLL2_VAR is implemented in
the clock core.
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Hai Pham <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
[Marek: Sync with Linux next 20230228 . Update from CLK to CPG core driver
Treat PLL2 as non-PLL2_VAR for now]
|
|
Add clock tables for R8A779F0 S4 SoC
Based on Linux commit 24aaff6a6ce4 ("clk: renesas: cpg-mssr: Add support
for R-Car S4-8") by Yoshihiro Shimoda and sync the tables up to Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Hai Pham <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
[Marek: Sync with Linux next 20230228 . Update from CLK to CPG core driver]
|
|
R-Car V3U has a CPG different enough to not be a generic Gen3 CPG but
similar enough to reuse code. Introduce a new CPG library, factor out
the SD clock and RPC clock handling and hook them to the generic Gen3
CPG driver so we have an equal state.
Based on Linux commit [1] and [2] by Wolfram Sang
[1] 8bb67d87346a ("clk: renesas: rcar-gen3: Factor out CPG library")
[2] 6f21d145b90f ("clk: renesas: cpg-lib: Move RPC clock registration to
the library")
Signed-off-by: Hai Pham <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
Marek: - Add rcar_clk_* prefix to all functions
- Rebase on changes to
clk: renesas: Introduce and use rcar_clk_get_rate64_div_table function
- Use u32_encode_bits/GENMASK bitfield ops
|
|
Add support for the R-Car M3-W+ (R8A77961) SoC.
R-Car M3-W+ is very similar to R-Car M3-W (R8A77960), which allows for
both SoCs to share a driver.
Based on Linux commit 2ba738d56db4 ("clk: renesas: r8a7796: Add R8A77961
CPG/MSSR support")
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Hai Pham <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
|
|
Rename CONFIG_CLK_R8A7796 for R-Car M3-W (R8A77960) to
CONFIG_CLK_R8A77960, to avoid confusion with R-Car M3-W+ (R8A77961),
which will use CONFIG_CLK_R8A77961.
Based on Linux commit 92d1ebae9abf ("clk: renesas: Rename CLK_R8A7796
to CLK_R8A77960")
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Hai Pham <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
|
|
Add clock tables for R8A779A0 V3U SoC from Linux 5.12,
commit 9f4ad9e425a1 ("Linux 5.12")
Signed-off-by: Hai Pham <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
--
Marek: - Add .reset_modemr_offset
- Sync tables from Linux 5.12
- Rebase on latest u-boot
|
|
Import RZ/G2E (R8A774C0) clock tables from Linux 5.9 commit
bbf5c979011a ("Linux 5.9").
Signed-off-by: Lad Prabhakar <[email protected]>
Reviewed-by: Biju Das <[email protected]>
|
|
This sync's the RZ/G2H clock tables with mainline linux 5.9 commit
bbf5c979011a ("Linux 5.9").
Signed-off-by: Biju Das <[email protected]>
Reviewed-by: Lad Prabhakar <[email protected]>
|
|
This sync's the RZ/G2N clock tables with mainline linux 5.9 commit
bbf5c979011a ("Linux 5.9").
Signed-off-by: Biju Das <[email protected]>
Reviewed-by: Lad Prabhakar <[email protected]>
|
|
This sync's the clock tables with the official release from
Linux 5.8-RC2 and update r8a774a1_mstp_table from Ref Manual
v1.00.
Signed-off-by: Adam Ford <[email protected]>
|
|
Import R8A77980 V3H clock tables from Linux 5.2.7 , commit 5697a9d3d55f.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
|
|
Add clock tables for R8A77965 from Linux 5.0 , except for the
crit, R and Z clock, which are neither used nor supported by
the U-Boot clock framework yet.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
|
|
Add clock tables for R8A77990 E3 SoC .
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
|
|
Import clock tables for R8A7794 E2 SoC from upstream Linux kernel v4.15-rc8,
commit bebc6082da0a9f5d47a1ea2edc099bf671058bd4 .
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
|
|
Import clock tables for R8A7792 V2H SoC from upstream Linux kernel v4.15-rc8,
commit bebc6082da0a9f5d47a1ea2edc099bf671058bd4 .
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
|
|
Import clock tables for R8A7791 M2W and R8A7793 M2N SoC from upstream Linux
kernel v4.15-rc8, commit bebc6082da0a9f5d47a1ea2edc099bf671058bd4 .
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
|
|
Import clock tables for R8A7790 H2 SoC from upstream Linux kernel v4.15-rc8,
commit bebc6082da0a9f5d47a1ea2edc099bf671058bd4 .
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
|
|
Add common clock code for Renesas RCar Gen2 platforms.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
|
|
Pull code which is common for RCar Gen2 and RCar Gen3 into
separate source file. No functional change.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
|
|
Add Kconfig entries for each SoC clock table, so they can be
compiled in or out at build time. This can reduce the size of
the binary if desired.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
|
|
Split the massive driver into smaller per-SoC drivers and pull the
common code into a separate file. This would allow configuring out
unnecessary clock drivers once the Kconfig changes are in and also
allow adding more clock tables easily.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
|
|
Add clock driver for the RCar Gen3 R8A7795 and R8A7796 SoCs .
This driver allows reading out the clock configuration set by
previous boot stages and enabling and disabling clock using
the MSTP registers. Setting clock is not supported thus far.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
