| Age | Commit message (Collapse) | Author |
|---|
|
Move the SERDES configuration check after clock and reset initialization
and change it from a hard failure to a skip of WIZ initialization. This
allows the driver to probe successfully when the SERDES has been
pre-configured by a previous boot stage (e.g., ROM or SPL).
This approach aligns with how the Linux kernel handles pre-configured
SERDES, where the driver gracefully skips reinitialization rather than
failing to probe.
Signed-off-by: Hrushikesh Salunke <[email protected]>
|
|
Pull request net-20251022
net:
- airoha: improvements
- Tighten a few more driver dependencies
- designware: fix bitbang init error
- phy: Make driver overloading get_phy_id depend on !COMPILE_TEST
- phy: add paged PHY register accessors
- make dhcp_run() common for NET and NET_LWIP
- dwc_eth_ops: Correct check for FDT_64BIT
- mediatek: mt7988: various fixup + MDIO detach
- phy: aquantia: switch to use phy_get_ofnode(), fix bindings typo
net-legacy:
- bootp: Prevent buffer overflow to avoid leaking the RAM content
- tftp: make TFTP ports unconditionally configurable
misc:
- uthreads: Make use of CONFIG_IS_ENABLED consistently
|
|
https://source.denx.de/u-boot/custodians/u-boot-at91
First set of u-boot-at91 features for the 2026.01 cycle:
This small fixes set includes a change on clocks register value and a
fix for the sam9x60ek default timer.
|
|
The Synchronous Abort and reset errors occurred due
to incorrect parameter passing during initialization.
Signed-off-by: Jim Liu <[email protected]>
[jf: add missing #if IS_ENABLED(CONFIG_BITBANGMII)]
Signed-off-by: Jerome Forissier <[email protected]>
|
|
With commit 597fe041a85f ("net/phy: enable get_phy_id redefinable") we
made get_phy_id a public but weak function, so that PHY drivers that had
required non-standard ways of getting the PHY ID could be supported.
However, overloading a weak function multiple times is (rightly) a link
error. At this point, we have two PHYs which make use of this feature,
so make both of them only available when COMPILE_TEST is unset, as part
of being able to support "allyesconfig" in the future.
Signed-off-by: Tom Rini <[email protected]>
|
|
Synchronize paged PHY helpers with Linux v6.17.
Add support for PHY devices that use paged register access by
implementing the following functions:
- phy_save_page(): Save current page number
- phy_select_page(): Switch to a specific page and return previous page
- phy_restore_page(): Restore previously saved page
Also adds read_page and write_page callbacks to the phy_driver
structure to enable driver-specific page handling.
These helpers allow safe access to paged PHY registers by ensuring
proper page selection and restoration,
even in error conditions, which will be used by the Airoha PHY driver.
Signed-off-by: Lucien.Jheng <[email protected]>
|
|
The commit 997786bbf473 ("drivers/net/airoha_eth: fix stalling in package
receiving") can be improved. Instead of returning previous descriptor
it's possible:
* do nothing in even descriptor case
* return 2 descriptor to the queue (current and previous) in the odd
descriptor case.
This patch:
* implements above approach
* remove logic not required within new approach
* adds note that PKTBUFSRX must be even and larger than 7
for reliable driver operations
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
|
|
In preparation for support of MDIO on AN7581, move the MT7531 MMIO logic
to a dedicated driver and permit usage of the mdio read/write function
to the mtk_eth driver.
This only affect MT7988 that can use MMIO operation to access the Switch
register. The MT7988 code is updated to make use of the external driver.
This permits Airoha driver to make use of DM_MDIO to bind for the MT7531
driver that have the same exact register.
Signed-off-by: Christian Marangi <[email protected]>
|
|
Correctly free the MDIO Bus on calling cleanup function. While at it
also fix a copy-paste error and rename the cleanup function name to the
more specific name.
Signed-off-by: Christian Marangi <[email protected]>
|
|
On exiting the phy_setting function for MT7988, the PHY page is never
restored to Page 0. This can cause all kind of problem with reading the
status of the PHY at runtime.
Correctly restore PHY page on exiting the PHY setting function.
Signed-off-by: Christian Marangi <[email protected]>
|
|
The PHY for MT7531/MT7988 are never actully turned ON/OFF for the
affected PHY as we are read/writing to the wrong PHY address.
This is caused by the fact that we use the MT753X_PHY_ADDR macro 2
times offsetting the address multiple times.
One in the _setup() function and one in the mt7531_mii_read/write.
Drop the additional usage of MT753X_PHY_ADDR in setup() to correctly
set the PHY.
Signed-off-by: Christian Marangi <[email protected]>
|
|
Use PHY API phy_get_ofnode() helper to get PHY DT node.
Signed-off-by: Beiyan Yun <[email protected]>
|
|
In this case, the mediatek network drivers cannot build outside of
ARCH_MEDIATEK or ARCH_MTMIPS, and so express this requirement in Kconfig
as well. In the case of DWC_ETH_XGMAC / DWC_ETH_XGMAC_SOCFPGA, the file
controlled by the DWC_ETH_XGMAC option references a socfpga-specific
array defined in the file controlled by DWC_ETH_XGMAC_SOCFPGA. Rework
these options in Kconfig to handle this dependency.
Signed-off-by: Tom Rini <[email protected]>
|
|
Some drivers which depend on SoCFPGA specific headers had not had
appropriate dependencies list in Kconfig. Add ARCH_SOCFPGA or
TARGET_SOCFPGA_SOC64 where appropriate.
Signed-off-by: Tom Rini <[email protected]>
|
|
This reverts commit a040578d8270ed8788d7663808ea63ce5ffd7840.
Based on feedback other SOCs (for example Star64) are using driver in non
DMA mode which is causing issues that's why revert this patch.
cdns,is-dma should be removed differently.
Signed-off-by: Michal Simek <[email protected]>
Reported-by: E Shattow <[email protected]>
|
|
SH HSCIF FIFO fixes, R-Car V4H/V4M DT corrections, R-Car V4H Sparrow
Hawk PCIe shutdown support before booting Linux.
|
|
The HSCIF RX FIFO may overflow when data are streaming from remote end
into the HSCIF while U-Boot is still starting up. In that case, HSFSR
bit RDF is set, but HSFDR field R is zero. This confuses .tstc callback
into considering RX FIFO to be empty, which leads to .getc to be never
invoked, even when user attempts to pass more input onto the command
line.
Fix this by considering the RDF flag in serial_rx_fifo_level(), which
is called from .tstc in case of no errors. If RDF flag is set, trigger
the .getc callback and let it clear the RX FIFO.
Signed-off-by: Marek Vasut <[email protected]>
|
|
In case the link is down, or the controller driver is removed before
booting the next stage, shut down the PCIe link, put both the remote
PCIe device and the controller into reset, and disable clock. This
way, the hardware is not left active when not in use.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Patrice Chotard <[email protected]> says:
- Update led_get_by_label()
- Fix led Kconfig
Link: https://lore.kernel.org/r/[email protected]
|
|
Add LED dependency for LED_ACTIVITY and LED_BOOT.
Signed-off-by: Patrice Chotard <[email protected]>
Cc: Yegor Yefremov <[email protected]>
Reviewed-by: Yegor Yefremov <[email protected]>
|
|
During led_init() execution, led_get_label() returns either the label
property (which is an obsolete property [1]) or the LED's node name.
It can't be the function name as dev parameter is NULL.
Later, during led_post_bind() execution, for the same LED, the attributed
label by led_get_label() can be the function name, as led_get_label()
dev's parameter is set.
During call sequence led_boot_on() => led_boot_get() => led_get_by_label()
with label given in parameter (priv->boot_led_label which is either the
label or node's name set previously in led_init()) can be different to
to uc_plat->label and returns -ENODEV.
Update led_get_by_label() to allow to retrieve LED also by its node name.
[1] https://www.kernel.org/doc/Documentation/devicetree/bindings/leds/common.yaml
Signed-off-by: Patrice Chotard <[email protected]>
Cc: Yegor Yefremov <[email protected]>
|
|
Remove default values for PMC PLL Analog Control Register(ACR) as the
values are specific for each SoC and PLL, so load them from PLL
characteristics structure
Signed-off-by: Manikandan Muralidharan <[email protected]>
Signed-off-by: Varshini Rajendran <[email protected]>
|
|
Add ACR in all PLL setting. Add correct ACR value for each PLL used in
different SoCs.
Signed-off-by: Manikandan Muralidharan <[email protected]>
Signed-off-by: Varshini Rajendran <[email protected]>
|
|
With commit c85b8071e7d3 ("virtio: blk: support block sizes exceeding 512
bytes") logic was added to detect the VIRTIO_BLK_F_BLK_SIZE capability and
to copy the block size reported by QEMU to the block device descriptor.
The logical block size can be set when invoking QEMU:
-drive if=none,file=4096.img,format=raw,id=vda \
-device virtio-blk-device,drive=vda,physical_block_size=4096,logical_block_size=4096
In U-Boot the logical block size is shown by command `virtio info`:
=> virtio info
Device 0: QEMU VirtIO Block Device
Type: Hard Disk
Capacity: 1024.0 MB = 1.0 GB (262144 x 4096)
There where two flaws which together hid that the logic was incorrect:
* VIRTIO_BLK_F_BLK_SIZE was missing in the driver capabilities and the bit
was filtered out.
* The result of the call to virtio_has_feature() was negated.
The problem became apparent when using ARM FVP as emulator which does not set
VIRTIO_BLK_F_BLK_SIZE.
Fixes: c85b8071e7d3 ("virtio: blk: support block sizes exceeding 512 bytes")
Reported-by: Debbie Horsfall <[email protected]>
Tested-by: Andre Przywara <[email protected]>
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
The pointer resp is declared but never assigned a value but is then
dereferenced. Fix this by assigning the pointer to the message buffer.
This issue was found by Smatch.
Reviewed-by: Udit Kumar <[email protected]>
Signed-off-by: Andrew Goodbody <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
Tested-by: Anshul Dalal <[email protected]>
|
|
In ti_sci_get_response the check for message sequence will return ret
on a fail but ret will be 0 at that point. Instead return -EINVAL.
Also change dev_dbg call to dev_err to be consistent with other error
detection code in the same function.
This issue was found by Smatch.
Reviewed-by: Udit Kumar <[email protected]>
Signed-off-by: Andrew Goodbody <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
Tested-by: Anshul Dalal <[email protected]>
|
|
temp is assigned the pointer returned by malloc which is used without a
NULL check and then never freed. Add a NULL check and ensure temp is
freed on all return paths.
This issue was found by Smatch.
Reviewed-by: Udit Kumar <[email protected]>
Signed-off-by: Andrew Goodbody <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
Tested-by: Anshul Dalal <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-watchdog
CI: https://dev.azure.com/sr0718/u-boot/_build/results?buildId=400&view=results
- watchdog: Tighten some driver dependencies in Kconfig (Tom)
|
|
The cv1800b_clk_setfield function returns void, but was doing "return
writel(...);" and while seemingly having a void function return a void
function is not a warning, when readl is a macro this problem is shown.
Correct the code to instead simply call writel.
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Yao Zi <[email protected]>
|
|
The WDT_DAVINCI driver is not safe to compile on 64bit platforms such as
allyesconfig on a 64bit host. Tighten the dependencies here to the
platforms which could use it today.
Signed-off-by: Tom Rini <[email protected]>
|
|
A few watchdog drivers cannot build without access to some platform
specific header files. Express those requirements in Kconfig as well.
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-microblaze
AMD/Xilinx/FPGA changes for v2026.01-rc1 v2
zynqmp:
- DT updates
- Enable new commands
mbv:
- Simplify defconfigs
clk:
- Separate legacy handler and use SMC handler
misc:
- Tighten TTC Kconfig dependency
net:
- Add 10GBE support to Gem
pwm:
- cadence-ttc: Fix array sizes
fwu:
- Add platform hook support
spi:
- Remove undocumented cdns,is-dma property
video:
- Fix DPSUB RGB handling
|
|
https://source.denx.de/u-boot/custodians/u-boot-tpm
TPM changes:
Make all drive names defined with U_BOOT_DRIVER unique
TEE changes:
Rework things such that sandbox will also traverse the optee directory
when SANDBOX_TEE is enabled, but only build one of the optee-specific
files when OPTEE is enabled.
EFI changes:
Up to now we were relying on the file extension to accept and load
an image over HTTP. We expected images to be either .iso or .img.
By wiring up internal existing functions we can try to mount any
file extension and reject it only if mounting fails.
part_driver_lookup_type
|
|
Remove cdns,is-dma DT property handling. Property is not the part of DT
binding and it is also hardcoded to value 1 in all DTs that's why remove it
because none is also testing value 0.
If there is any use case when this configuration should be supported this
patch can be reverted.
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/6205c6585589b423692b6ed063506b4c51c04c77.1760006086.git.michal.simek@amd.com
|
|
All instances of the U_BOOT_DRIVER must use a unique name or they will
lead to link time failures due to name space conflicts when both are
present. In this case the driver was reusing the tpm_tis_i2c name.
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
Signed-off-by: Ilias Apalodimas <[email protected]>
|
|
The intention of how this Makefile was written was to allow for sandbox
to build and test drivers still while otherwise requiring OPTEE to be
enabled. This however didn't work quite right in practice as sandbox
could enable some drivers which would then fail to link. Rework things
such that sandbox will also traverse the optee directory when
SANDBOX_TEE is enabled, but only build one of the optee-specific files
when OPTEE is enabled.
Signed-off-by: Tom Rini <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
Signed-off-by: Ilias Apalodimas <[email protected]>
|
|
Correct the memory and IO mbus windows size increments in mvebu_pcie_bind.
Currently, pcie1 controller resource_size(&mem) and resource_size(&io)
checks result in a failure. This is because mem.end and io.end must be
incremented at the end of pcie0 windows assignment.
Signed-off-by: Tony Dinh <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
This driver cannot link without access to functions that are defined in
files that are only build on some platforms. Express those requirements
in Kconfig as well.
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
In octeontx_mmc_io_drive_setup drive and slew are tested for being less
than 0 but they are declared as uint fields so this test must always
fail. Just remove the test.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
|
|
The check for no response expected in octeontx_mmc_send_cmd needs parens
adding for proper interpretation.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
|
|
Smatch reported an issue with a test that was always true in that an
unsigned variable will always be >= to zero. This led to a closer look
at the code which showed that some static functions returned values that
were always discarded so make those functions return void. Also make
the passing of block counts in those functions always use lbaint_t.
Signed-off-by: Andrew Goodbody <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Matthias Schiffer <[email protected]> says:
Following a discussion on the LKML [1], there has been a clarification
of the correct use of the rgmii(/-rxid/-txid/-it) phy-modes [2] - namely,
that they don't describe the interface at the MAC or PHY boundary, but
whether the PCB traces add delays or not (where it is
implementation-defined whether the delays are added on the MAC or PHY
side in the latter case).
Accordingly, a fixup has been implemented in the am65-cpsw-nuss driver
to make it follow the clarified rules [3]; apply the same change to
U-Boot. Backwards compatibility is preserved: using an old DTB with
the wrong phy-mode only results in a warning message, but keeps the
Ethernet working. With a new DTB from Linux 6.17+ that sets the mode to
rgmii-id, these changes are necessary to avoid using an unsupported/
reserved configuration. See the commit message of patch 2/2 for some
additional detail.
[1] https://lore.kernel.org/lkml/[email protected]/
[2] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=c360eb0c3ccb95306704fd221442283ee82f1f58
[3] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=ca13b249f291f4920466638d1adbfb3f9c8db6e9
Link: https://lore.kernel.org/r/[email protected]
|
|
The am65-cpsw driver currently sets the SEL_RGMII_IDMODE flag in a MAC's
mode register to enable or disable the TX delay. While this was supported
for earlier generations of the CPSW controller, the datasheets of all
modern TI SoCs using the am65-cpsw MAC state that the TX delay is fixed,
and the SEL_RGMII_IDMODE bit is documented as reserved in most of them.
Furthermore, while it was found that this bit does in fact disable the TX
delay, [1] states that this setting is truly unsupported by TI and not
just undocumented.
Following the clarification of the rgmii* phy-mode values in the Linux
DT bindings in [2], the Linux am65-cpsw driver was changed in [3] to
account for the fixed TX delay by fixing up the mode passed to the PHY
driver; a similar fixup already existed in the TI icssg-prueth driver.
[4] followed up on this by explicitly clearing the SEL_RGMII_IDMODE flag
to handle the case where it is set by the bootloader or other firmware
before Linux.
With the above changes, Device Trees that set the recommended "rgmii-id"
mode are now appearing in Linux 6.17+. Avoid setting the unsupported
SEL_RGMII_IDMODE flag for such Device Trees, and instead fix up the PHY
interface mode, thus aligning the U-Boot driver with the Linux kernel.
[1] https://www.spinics.net/lists/netdev/msg1112647.html
[2] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=c360eb0c3ccb95306704fd221442283ee82f1f58
[3] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=ca13b249f291f4920466638d1adbfb3f9c8db6e9
[4] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=a22d3b0d49d411e64ed07e30c2095035ecb30ed2
Signed-off-by: Matthias Schiffer <[email protected]>
|
|
The MCHP_PIT64B_TIMER driver is not safe to compile on 64bit platforms
such as allyesconfig on a 64bit host. Tighten the dependencies here to
the platforms which use it today.
Acked-by: Eugen Hristev <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This driver has never been enabled and currently has build problems
related in part to incorrect out_le32 calls. Remove it.
Signed-off-by: Tom Rini <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-nand-flash
This series adds significant and valuable work by Mikhail Kshevetskiy to
align spi-mem with Linux 6.16. It also includes contributions to the mtd
performance patches, a work started by Miquel Raynal and improved by
Mikhail Kshevetskiy. Additionally, two patches tighten dependencies on
the Atmel driver.
The patches pass the pipeline CI:
https://source.denx.de/u-boot/custodians/u-boot-nand-flash/-/pipelines/27873
|
|
https://source.denx.de/u-boot/custodians/u-boot-fsl-qoriq
CI: https://source.denx.de/u-boot/custodians/u-boot-fsl-qoriq/-/pipelines/27882
- crypto/rng: double the entropy delay interval for retry
- Make RAMBOOT_PBL only be valid for PowerPC or ls1021AI
|
|
During entropy evaluation, if the generated samples fail any statistical test,
then, all of the bits will be discarded, and a second set of samples will be
generated and tested.
Double the ent_delay to give more chance to pass before performing retry.
Signed-off-by: Gaurav Jain <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
The function cv1800b_set_tap_delay is only called by
cv1800b_execute_tuning. The latter is where we currently have the #if
guard around MMC_SUPPORTS_TUNING, and so with the option disabled we
have an unused function warning. Move the guard to cover both functions.
Signed-off-by: Tom Rini <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
In order to enable and build with SPL_REGULATOR_PWM we need to have both
SPL_DM_REGULATOR and SPL_DM_PWM enabled. Build-wise, we can have SPL
have PWM regulator support without enabling it in U-Boot itself so drop
that dependency.
Signed-off-by: Tom Rini <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
